Read this manual carefully before using this product. Heed the
instructions to keep your warranty for this product. Prevent fire or
electric shock. This product may only be repaired by qualified
servicing personnel. Keep this manual for future reference.
-
Keep the original packaging in case of defects. Return the product in its original
packaging.
-
Consult a professional before installing this product.
- This product contains high-voltage parts; NEVER open the housing!
-
Never pull the power cord while disconnecting it from the mains socket. Remove the
power cord by pulling the connector.
-
-
Never connect or disconnect the power cord with wet hands.
If the connector or the power cord is damaged; they need to be replaced (or repaired) by
a qualified serviceman.
-
If the housing is damaged in such away so you can see internal parts, you may NEVER
connect the power cord with the mains socket and you may NEVER switch the product
on. Please contact your dealer if this situation occurs.
- This product may only be repaired by qualified servicing personnel.
-
-
Only connect this product with a 230VAC/50Hz earthed power supply.
Don't install this product near heat sources like radiators etc. Don't install on vibrating
surfaces.
- Always disconnect this product during thunderstorms. Also disconnect this product when
not in use for a long period of time.
- Water vapour might occur at first use after a long period of not using this product. Please
let the product reach room temperature before using it.
-
Never use this product outdoors or in a wet environment.
- To prevent accidents in professional environments; please heed instructions and
guidelines at all times.
-
-
Keep this product out of reach of children.
Don't use cleaning spray to clean this product. Remainders of cleaning sprays are
responsible for the build-up of dust and grease. Please contact a servicing company
when this product is malfunctioning.
-
-
-
-
-
Please clean your hands before using this product.
Don't use excessive force while controlling this product.
Place this product on a stable and a evened surface.
NEVER look directly in the projection lens.
Only power this product off when the fan stops blowing; the lamp may blow during
abrupt shutdowns? this may cause fire or electric shock.
NEVER touch the grille or bottom part of the housing because of heated airflows.
Clean the air filter at least once a month and NEVER look directly into the air filter
during operation.
-
-
-
-
Never clean this product with chemical solutions. This might damage the paint. Use a
dry cloth instead.
Install out of the way of electronic devices that might cause humming malfunctions with
this product.
- Only use identical servicing parts when servicing this product. Irreparable damages or
radiation might occur.
2
- Turn this product of before disconnecting it from the mains power supply. Remove the
power chord and other connection cables before (re)moving this product.
MAINTENANCE FILTER
-
Don't damage the power chord by stepping on it. NEVER install this product across
walking routes.
The filter should be cleaned at least once a month (more often in dusty environments), or
the projector will overheat.
- This product requires a 230VAC/50Hz power supply. Please inform if you're mains
supply meets these specifications. When you use this product abroad, please inform if
the mains supply meets the above requirements.
1. Turn the projector of with the On/Off switch
and remove the plug from the mains supply.
Never turn the projector on without a filter.
2. Remove the grille like indicated below
(arrows).
This marking means that this product operates on a highly dangerous voltage.
By touching the internal, electrical parts you risk suffering an electric shock
which might result in harmful damage to you or others in the direct area.
3. Use the smallest amount of water or thinned
dish cleanser to clean the filter. Dry the filter
sufficiently. Never install a moist filter in this
projector.
This marking means that it's very important to read and heed the instruction
manual at all times.
4. Follow the steps (1-2) in opposite order to
complete the installation.
PRODUCT DESCRIPTION
ACCESSOIRIES
This projector was designed using highly advanced technology and can be used in schools,
companies, institutes, meeting rooms, hotels, clubs, supermarkets, theatres etc.
Thank you for buying this Multimedia LCD Projector! Please check if the following
accessories are included in the package:
Because of the compact dimensions of this product you can carry it to any place you like.
Projector
1
1
1
1
1
1
You can connect this product with computer and video input signals. (Computer resolutions
up to 1024 768 and video signals like DVD, VCR, TV, SVHS etc.). Resolutions over
1024 768 are not connectable. Please reduce your computer's resolution before connecting
it with this product.
Remote control
Power cord
Fuse (5A)
Lens cloth
Manual
If a trapezoid image occurs you can adjust this with the Keystone-correction and solve the
problem.
The OSD menu can be called upon with the remote control (IR function).
The OSD language can be set to English as well as Chinese-simp, Spanish, French, German,
Italian, Russian, Portuguese.
14
3
TROUBLE SHOOTING
SPECIFICATONS
Please refer to this chapter when you encounter a problem list prior to contacting your
dealer.
Power consumption: ....................................................... <220 W
Lamp power: .................................................................... 150 W
Color temperature: ......................................................... 9300 K
Lamp life: ....................................................................8000 Hrs
Power requirements: .......................................... 230 VAC/50 Hz
Running current: ................................................................. <2 A
Brightness: ................................................................. 1200 Lm
Resolution.......................................................800*600
Lens: ....................................................................f160mm/F=2.9
Contrast: ............................................................................800:1
Number of Pixels: .............................................................. 1.0 M
Color system: ............................................. NTSC/PAL/SECAM
Keystone-correction: ........................................................... 15
Problem:
Possible solution(s):
Projector not connected to mains.
Projector not turned on.
Blown fuse.
No power
Remote doesn't operate
Projector turned on to quickly after last
turn off (needs 5 minutes).
Batteries defect.
Aim remote correctly at IR receiver.
No image
Lens cap not removed.
Projector turned off.
Faulty wiring.
Selected the wrong input signal.
Projector turns off automatically
(no more power)
Air in-and/or outlets and/or filter
are covered or blocked.
Lamp doesn't function
Power supply isn't correct.
Temperature is too high.
Defect lamp.
Max. advisable duration of usage: ..............................
24 Hrs
REPLACING THE LAMP
Projection picture size: ............................................ 50-100 inch
Dimensions: ..................................................310 255 95 mm
Weight: ............................................................................. 6 Kg
This lamp has a maximum lamp life. The color balance will change when the light intensity
decreases. The image will also blur. Replace the lamp if this is the case.
Turn the projector of and remove the power cord.
1. Place the projector on a cloth to put loose parts on.
2. Turn the screw loose and open the lid.
Specifications and design may be altered by the manufacturer
without any communication.
3. Remove the 4 screws holding the lamp unit. Pull the unit straight up.
4. Now replace the lamp and follow the steps (1-4) in opposite order to complete the
installation.
4
13
OSD menu
Menu setting method
PROJECTOR INSTALLATION
1. Using the projector press menu key,
enter the main menu window (picture one)
Please use the setup indicated below:
Bright
Contrast
Color
2. Press
key the menu enter
Tone
Sharpness
English
into image
>
volume
system
image secondary menu
>
Speaker
L
Speaker
R
function
>
>
setting
>
Screen
Subwoofer
3.Enter the secondary menu use
to elect the function (picture two
key
Speaker C
4. use
key to change the parameter
5. Finished to adjust the parameter press the
menu key again exit the window
6. Repeat operate the 2 5step
till finished all the parameter's setting.
press exit key,exit the menu window
Sharpness
English
Volume menu adjustment
Adjust the volume of the speaker or amplifier equipment
b. Choose the audio output method when setting as line
the projector speaker will stop work.
DVD
Projector
Amplifier
Volume
Output
Volume
Output
50
speaker
speaker
Appreciate seats
Door
Function menu adjustment
a. Switch image display mode (From 16:9 to 4:3 ,zoom function)
b. Setting the menu auto-exit time
Speaker
Ls
Speaker
Rs
c. Setting Blue screen or no when no signal input.
Zoom
OSD.Time
Bluescreen
4 3
5
OFF
Zoom
OSD.Time
Bluescreen
4 3
5
OFF
SETTING UP THE SCREEN AND PROJECTOR
Place the projector on a smooth and stable surface. Please don't place any objects on top,
underneath or next to this product to ensure proper and sufficient cooling. De distance
between the projector and the projector screen varies from the screen's size. Please refer to
the table below for the correct setup distances.
TV mode
AV/SV mode
Screen Size
50"
4:3
16:9
4. System menu adjustment
a. Colour -S can choose auto PAL NTSC SECAM four mode
when the projector connect the new video devices if you don't know
which system of the video output signal please setting Colour -S
as auto
2.45m
3.45m
4.73m
2.65m
3.75m
5.15m
72"
100"
12
5
Please follow the instructions below when a trapezoid occurs on the projector screen:
FOCUSING AND KEYSTONE ADJUSTMENT
Screen
FOCUSING
Turn the lens to focus the projected image.
Screen
symmetry
axis
Projector
NOTE: When you replace the projector from a cold to a warm environment water vapour
might occur. Don't turn the projector on when this occurs but wait until the vapour
has disappeared.
Installed correctly,
the image is rectangular.
Incorrect installation,
the images left-right small.
Incorrect installation,
the images right-left small.
CEILING/TABLE MOUNT SETUP
KEYSTONE
Contact a professional service man to mount this projector to a ceiling. Follow the
instructions below for the correct projector positions:
If a projected picture has keystone distortion, correct image with Keystone adjustment. The
image becomes trapezoid shape when the screen or project is not level. Please reposition
the projector to improve its angle to the screen. However, the circumference of the image
may not be focussed.
Projector
Projector
Screen
Screen
Projector
Front projection ceiling mount
Rear projection ceiling mount
Projector
Screen
Screen
Keystone
Screen
Screen
Projector
Projector
Front projection table mount
Rear projection table mount
If not able to use the Keystone correction function to correct the trapezoid distortion, please
reduce of the projector to centre the screen vertically.
WARNING
This projector might damage beyond repair when it's incorrectly mounted on a ceiling or
when its incorrectly installed on a surface or installed on a incorrect surface. It may also
inflict damage to persons within close vicinity.
This projector can only be used in an environment with a temperature not exceeding the
range of 0~35 . The projector may malfunction if temperatures vary outside the normal
operating range.
The sharpness of the screen might be interrupted when the projector is being used in a
dusty, wet, moist or smoke filled environment. The projector might malfunction in a moist
or wet environment. Take care of sufficient ventilation around the projector. Otherwise this
projector might overheat and cause life threatening situations!
6
11
PROJECTOR (FRONT VIEW)
MAKING CONNECTIONS
The sockets for making connections on the back panel of the projector are shown below:
TOP-Key
Fan grille
Keystone
Lens
button: Push this button to turn the projector on when it's in stand-by mode and
push it again to return to stand-by mode.
Video input: Connect with a composite output signal from a video device.
Audio input: Connect with an audio signal from a video or audio device.
VGA input: Connect with a computer output signal.
MENU button: Push this button to open the menu.
/
/
/
buttons: Use these buttons to navigate through the menu.
PC/AV button: Use this button to select the video source you want to use. You can
select between signals like PC, VCR or DVD. The beamer will switch between
video sources every time you push this.
S-Video input: Connect with an S-video output signal from a video device.
RF input: Connect the antenna of the wired television.
LED indicator: Put the projector into stand-by mode ,the LED is flashing; when the
projector is working, the LED is light red.
Fan grille: Cool air inlet.
AC Power Switch:Turn the projector on
or off. When using Remote Control
Unit, turn the switch to ON. And turn it
to OFF when the projector is not used.
Focusing the image by turning the lens.
PROJECTOR CONTROL
Here is a 5 Amps fuse installed for the
projector.
Remove the lens cap after connecting the mains cable.
1. Insert 2 batteries in the battery compartment.
AC Power Jack: Connect AC Power
Cable (supplied) to the projector.
2. Turn the On/Off switch to "ON"; the LED will
flash slowly.
3. Push the "ON" button on your remote or the
one on the projector. The LED will light up red.
4. Hold one of these buttons for 2 seconds. The lamp will warm-up now. After 2 minutes
the image appears on the projector screen.
IR receiver
5. Focus the image with the lens and setup the size and position of the image. You can
correct the Keystone if necessary.
6. Setup the required image quality with the OSD menu.
7. Push the "ON" button again and the lamp will switch off.
8. The LED will flash rapidly and the fans will keep operating for around 5 minutes to cool
the projector. Do not turn the projector on again during this period!
10
7
CONNECT MAIN EQUIPMENT
REMOTE CONTROL
POWER button: Push this button to turn the projector on when it's in stand-by
mode and push it again to return to stand-by mode.
MENU button: Push this button to open the menu.
/
/
/
buttons: Use these buttons to navigate through the menu.
AV/PV button: Use this button to select the video source you want to use. You can
select between signals like PC, VCR or DVD. The projector will switch between
video sources every time you push this.
Connecting video equipment
Without S-video output terminal.
Connecting audio equipment
With RCA output terminal.
POWER
For turning the power on.
MUTE
For temporarily turning off
the sound.
RETURN
Cancel the direct channel
selection.
Number Amount
Selects the amount of TV
channel number display.
DISPLAY
Information display.
Number Buttons
Selects TV channel directly.
PICTURE MODE button
For selecting image effect: bright, soft,
normal, user.
AV/TV
For selecting input source.
Adjustment buttons
Selects a channel.
Selects (vertically) or adjusts
an operation or item.
Volume control.
Selects (horizontally) or
adjusts an operation or item.
Connecting an cable with
matched receiving antenna.
Connecting PC or DVD
equipment VGA output terminal.
MENU
For displaying adjustment
and setting screens.
DISPLAY MODE
16:9 or 4:3.
PICTURE OVERTURN
For selecting the image display
modes.
No using.
Connecting video equipment
With S-video output terminal.
PRECAUTIONS
You need to dry the remote control with a dry cloth immediately when it gets wet.
When the battery hasn't been used for a long time we advise you to remove it from
the remote. Be sure that children can't reach the removed button cell. Swallowing a
button cell will cause a child a lot
of harm and is very dangerous!
8
9
|