Peerless Industries Flat Panel Television MIS374 User Manual

Installation and Assembly:  
20" Column Tilt Mount for 10" - 24" LCD Flat Panel  
Screens Using ST 630  
Model: MIS374  
Max Load Capacity: 80 lb (36.3 kg)  
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com  
ISSUED: 03-30-07 SHEET #: 124-9052-1  
 
Installation to Solid Concrete Column  
WARNING  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the column will safely support the combined load of the equipment and all attached hardware and  
components.  
Note: Two Alligator® anchors and two #14 x 2-1/2  
hex head wood screws from ST 630 fastener pack are  
required to complete assembly.  
concrete  
surface  
1
Make sure that column plate (A) is level, use it as a  
template to mark four mounting holes. Drill four 1/4"  
(6 mm) dia. holes to a minimum depth of 2-1/2"  
(64 mm). Insert anchors (B) in holes flush with  
column as shown (right). Place column plate over  
anchors and secure with four #14 x 2-1/2" screws  
(C). Level, then tighten all fasteners.  
1
B
Drill holes and insert anchors (B).  
2
A
B
C
WARNING  
• Tighten screws so that column plate is firmly attached,  
but do not overtighten. Overtightening can damage  
screws, greatly reducing their holding power.  
Place plate (A) over anchors (B) and secure with screws (C).  
3
• Never tighten in excess of 80 in. • lb (9 N.M.).  
WARNING  
• Always attach concrete expansion anchors directly to  
load-bearing concrete.  
• Never attach concrete expansion anchors to concrete  
covered with plaster, drywall, or other finishing mate-  
rial. If mounting to concrete surfaces covered with a  
finishing surface is unavoidable, the finishing surface  
must be counterbored as shown below. Be sure  
concrete anchors do not pull away from concrete  
when tightening screws. If plaster/drywall is thicker  
than 5/8", custom fasteners must be supplied by  
installer.  
B
concrete  
column  
A
C
CORRECT  
INCORRECT  
column  
plate  
concrete  
concrete  
column  
plate  
plaster/  
drywall  
plaster/  
drywall  
ISSUED: 03-30-07 SHEET #: 124-9052-1  
3 of 4  
 
Installation of ST 630 Tilt Assembly  
Note: Tilt assembly from ST 630 is required for assembly  
Attach tilt assembly to column plate (A) using two 1/4-20 x 1/2 phillips screws (D), two split washers (F) and two flat  
washers(E).  
2
TILT  
ASSEMBLY  
A
E
F
D
Refer to Attaching Adapter Plate to Flat Panel Screen section of ST 630 instruction manual to complete assembly.  
ISSUED: 03-30-07 SHEET #: 124-9052-1  
4 of 4  
©2007, PeerlessIndustries, Inc. Allrightsreserved.  
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.  
 

Philips Answering Machine Elegance 55 User Manual
Philips Cassette Player AQ6401 User Manual
Philips Laptop T 870 User Manual
Philips Power Supply SJA1185 User Manual
Philips TV Antenna SDV2210 27 User Manual
Philips Universal Remote SBC RU 520 87U User Manual
Philips Work Light P 5761 D User Manual
Pioneer Car Video System XVHTD1 User Manual
Pitco Frialator Fryer SF14 UFM User Manual
Precor Treadmill 91 User Manual