Pelco Home Security System C2445M D User Manual
ADDENDUM  
Addendum No. C2499M-A  
Date November 17, 2005  
Manuals Affected Spectra III™ SE Series Dome Drive Manuals: C2443M-C, C2444M-C, and C2445M-D  
Manual Update The following are manual changes for Spectra III SE software Version 1.28 and greater and instructions for accessing a  
Spectra III EVS dome system.  
Presets  
Spectra III SE system presets have been upgraded from 80 to 150. Each of the user-definable presets can be programmed to use pan, tilt, camera settings,  
and motion detection. The programmable presets are numbered 1-32, 35-82, and 100-150.  
The following presets are predefined for specific functions:  
33  
34  
88  
89  
“Flip” command  
95  
96  
97  
98  
99  
Select main programming menu  
Stop a scan  
“Pan zero” command  
IR filter IN (color)  
Random scanning  
Frame scanning  
IR filter OUT (black-white)  
90-91 Manual limit stops  
92-93 Scan limit stops  
Start auto scanning  
Title Text  
Title Text has been added to the Dome Settings menu. The title text is the  
label used to identify the camera when it is viewed on the monitor. Up to  
20 characters can be used for a title.  
DOME SETTINGS  
TITLE TEXT  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<TITLE TEXT>  
<ALERT>*  
ENABLE TITLE TEXT  
<EDIT TITLE TEXT>  
BACK  
EXIT  
To edit the title text label, do the following:  
1. Use the joystick to position the cursor beside EDIT TITLE TEXT.  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
2. Press Iris Open.  
LABEL FOR PRESET  
PRESET NUMBER ------  
3. Use the joystick to position the cursor beside a character. Press Iris Open to select the character. To clear a  
character, position the cursor beside BACKSPACE and then press Iris Open.  
1234567890  
OK  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
CANCEL  
SPACE  
4. When the title is completed, move the cursor to OK. Press Iris Open to return to the Title Text menu.  
5. Enable the title text label by doing the following:  
abcdefghij  
klmnopqrst  
uvwxyz*;:  
BACKSPACE  
a. Move the cursor beside ENABLE TITLE TEXT.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view the selections. Select ON and then press Iris Open to enable the title text.  
(Continued on next page)  
 
OPERATION/PROGRAMMING  
Spectra III™ SE Series  
®
Models DD53C22 & DD53C22-X  
C2444M-C (1/04)  
 
OPERATION/PROGRAMMING MANUAL  
MODELS DD53C22 & DD53C22-X  
22X LowLight™ COLOR TECHNOLOGY  
 
CONTENTS  
WELCOME ................................................................................................................................................................................................ 5  
GETTING STARTED .......................................................................................................................................................................... 5  
HOW TO OPERATE YOUR DOME SYSTEM .............................................................................................................................................. 6  
ACCESSING MAIN MENU (PRESET 95) .......................................................................................................................................... 7  
CM6700/CM6800 ................................................................................................................................................................... 7  
KBD200A/KBD300A (DIRECT MODE ONLY) ........................................................................................................................... 7  
CM9500 .................................................................................................................................................................................. 7  
CM9740/CM9760 ................................................................................................................................................................... 7  
KBD4000/KBD4002 (GENEX MULTIPLEXER) .......................................................................................................................... 8  
MPT9500 ................................................................................................................................................................................ 8  
PELCONET ............................................................................................................................................................................... 8  
LANGUAGE .............................................................................................................................................................................................. 11  
SYSTEM INFORMATION.......................................................................................................................................................................... 12  
DISPLAY SETUP ....................................................................................................................................................................................... 13  
<LABEL POSITION> ......................................................................................................................................................................... 14  
DOME SETTINGS ..................................................................................................................................................................................... 15  
<CAMERA> ..................................................................................................................................................................................... 15  
TYPE OF LIGHTING ................................................................................................................................................................ 15  
AUTO FOCUS ......................................................................................................................................................................... 15  
ZOOM LIMIT .......................................................................................................................................................................... 16  
ZOOM SPEED ......................................................................................................................................................................... 16  
LOW LIGHT LIMIT .................................................................................................................................................................. 16  
<ADVANCED CAMERA SETTINGS> ............................................................................................................................................... 17  
SHUTTER SPEED .................................................................................................................................................................... 17  
AGC LIMIT ............................................................................................................................................................................. 17  
AUTO IRIS .............................................................................................................................................................................. 18  
AUTO SHARPNESS ................................................................................................................................................................ 19  
AUTO WHITE BALANCE ........................................................................................................................................................ 19  
BACKLIGHT COMPENSATION (BLC) ...................................................................................................................................... 20  
VIDEO LEVEL .......................................................................................................................................................................... 20  
<MOTION SETTINGS> .................................................................................................................................................................... 21  
AUTO FLIP .............................................................................................................................................................................. 21  
PROPORTIONAL PAN ............................................................................................................................................................. 21  
PARK TIME ............................................................................................................................................................................ 22  
SCAN SPEED ......................................................................................................................................................................... 23  
PRESET FREEZE FRAME ........................................................................................................................................................ 23  
LIMIT STOPS .......................................................................................................................................................................... 24  
AZIMUTH ZERO ..................................................................................................................................................................... 25  
<POWER UP> .................................................................................................................................................................................. 26  
POWER UP ACTION ............................................................................................................................................................... 26  
<LINE SYNC> .................................................................................................................................................................................. 27  
<PRESETS> ..................................................................................................................................................................................... 28  
<PATTERNS>................................................................................................................................................................................... 30  
<ZONES> ........................................................................................................................................................................................ 31  
2
C2444M-C (1/04)  
 
<WINDOW BLANKING> ................................................................................................................................................................. 32  
REVERSE ................................................................................................................................................................................ 34  
BLANK ALL ABOVE/BLANK ALL BELOW ............................................................................................................................... 34  
<ALARMS> ..................................................................................................................................................................................... 35  
<AUX> ............................................................................................................................................................................................. 38  
<ALERT> ......................................................................................................................................................................................... 39  
REPEAT................................................................................................................................................................................... 39  
ACK ACTION .......................................................................................................................................................................... 40  
ACTIVATE AUX ....................................................................................................................................................................... 40  
CURRENT READING .............................................................................................................................................................. 40  
ALERT RESET ......................................................................................................................................................................... 40  
<CLEAR> ......................................................................................................................................................................................... 41  
<PASSWORD> ................................................................................................................................................................................ 42  
RESET, CYCLE, POWER, REBOOT ............................................................................................................................................................ 43  
RESET CAMERA .................................................................................................................................................................... 43  
CYCLE CAMERA POWER ....................................................................................................................................................... 43  
REBOOT SYSTEM .................................................................................................................................................................. 43  
SOFTWARE/LANGUAGE FILE UPLOAD ................................................................................................................................................... 44  
UPLOAD ICON ................................................................................................................................................................................. 44  
SPECIFICATIONS ...................................................................................................................................................................................... 45  
REGULATORY NOTICES ........................................................................................................................................................................... 46  
C2444M-C (1/04)  
3
 
WELCOME  
Thank you for purchasing Pelco’s premier integrated dome system, Spectra III SE. Your new  
system features a high resolution, color camera/optics package with LowLight™ technology and  
programmable dome drive software.  
This manual is designed to be a reference tool for the operation and programming of your  
system. Inside you will find information about Spectra III SE’s features and commands, as well  
as a detailed menu tree.  
Getting Started  
You will need to install your dome system before using this manual. Refer to the installation  
packet supplied with the back box for installation instructions.  
Once installed apply power to the Spectra III SE dome system. The system will start a configura-  
tion sequence. When configuration is done, the following information is displayed:  
Pelco Spectra III SE  
*Version X.XX  
D Address: 1  
P Address: 2  
Comm 2400, N, 8, 1  
CONFIGURE DONE  
This information will remain on the monitor until dome operation begins.  
Refer to the following pages to learn how to operate and program your dome system.  
* Pressurized Spectra III SE dome systems require software version 1.25 or higher to monitor  
temperature, pressure, and dew point.  
C2444M-C (1/04)  
5
 
HOW TO OPERATE YOUR DOME SYSTEM  
Operation  
How to Control  
Pan and Tilt  
Move joystick or press the direction keys left/right and up/down.  
Zoom Far  
To zoom far, do the following:  
1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the 32X zoom limit.  
2. Release the button or joystick for one second.  
3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you have the  
picture you want or reach the digital zoom1 limit.  
Zoom Wide  
Press the Zoom Wide button or turn the joystick counterclockwise.  
Scanning  
Stop Scan  
Preset 96  
Preset 97  
Preset 98  
Preset 99  
Random Scan  
Frame Scan  
Auto Scan  
Presets  
Patterns2  
Zones  
Refer to the documentation supplied with the control system.  
Refer to the documentation supplied with the control system.  
Refer to the Zones section and to the documentation supplied with the control system.  
Refer to the Alarms section in this manual.  
Alarms  
Auto Flip  
Turn on or off in the programming menu. Refer to the Auto Flip section in this manual.  
1 Digital zoom magnifies the image electronically and the picture may appear pixilated. The larger the digital zoom limit the  
greater the reduction in resolution.  
2 The dome cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern.  
6
C2444M-C (1/04)  
 
Accessing Main Menu (Preset 95)  
You can call up the main menu on your monitor by programming (setting or creating) preset 95  
(preset 28 if in AD32-preset mode).  
Programming preset 95 for Pelco’s controllers varies according to the type of controller you are  
using. Instructions for programming preset 95 are given below for various Pelco controllers.  
CM6700/CM6800  
1. Enter the number of the Spectra dome system and press the CAM key.  
2. Enter 95 and hold the PRESET key for two seconds.  
3. In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.  
KBD200A/KBD300A (DIRECT MODE ONLY)  
1. Enter 95.  
2. Hold the PRESET key (approximately five seconds) until the main menu appears on the  
screen.  
CM9500  
1. Enter the number of the Spectra dome system and press the CAM key. The Main menu  
appears.  
2. Highlight SETUP in the Main menu and press the SELECT key.  
3. Highlight CAM in the Setup menu and press the SELECT key.  
4. Highlight PRESET in the Camera menu and press the SELECT key.  
5. Enter 95 and press the F1 key. The main menu appears.  
CM9740/CM9760  
1. Press the ESCAPE key to open the Main menu. Select DEF. The Define Submenu appears.  
2. Enter your four-digit PIN if this is your first time entering this mode.  
3. Enter 95 and select PRST. The main menu appears on the monitor.  
4. Select the Quit icon to return to the default menu.  
(Continued on next page)  
C2444M-C (1/04)  
7
 
KBD4000/KBD4002 (GENEX® MULTIPLEXER)  
1. Press the SPOT MONITOR key.  
2. Enter 95, then hold the PRESET key (approximately five seconds) until the main menu  
appears on the screen.  
MPT9500  
Standard Coaxitron Mode  
1. Enter 95 and press the PRESET SET key.  
2. Position the asterisk in the YES row and press the F1 key. The main menu appears.  
Extended Coaxitron or RS-485 Mode  
1. Enter 95 and press the PRESET SET key.  
2. Press the F2 key. The main menu appears.  
PelcoNet™  
1. Check the Set box.  
2. Click the preset 95 button. The main menu appears.  
8
C2444M-C (1/04)  
 
QUICK START GUIDE – SYSTEM SETUP  
SPECTRA III  
LANGUAGE  
ENGLISH  
Presets  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT**  
The following presets are reserved for special functions.  
Preset  
33  
Function  
Flip command  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Quick Programming Guide  
90-91  
92-93  
95  
96  
97  
Manual limit stops  
Scan limit stops  
Select main programming menu  
Stop a scan  
Random scanning  
Frame scanning  
Start auto scanning  
EXIT  
Access main menu (preset 95). See the Accessing Main Menu  
(Preset 95) section.  
DOME SETTINGS  
DISPLAY SETUP  
SYSTEM INFORMATION  
PRESET LABEL  
ZONE LABEL  
(2 SECS)  
(2 SECS)  
(2 SECS)  
(2 SECS)  
OFF  
DOME DRIVE MODEL  
DD53C22  
AVAILABLE  
XX.X  
Use the joystick* to position the cursor beside menu selection.  
Press Iris Open, the submenu/cursor moves to the right.  
Move the joystick up or down to view selections.  
Press Iris Open to make selection.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
98  
99  
BACK BOX MEMORY  
SOFTWARE VERSION  
BIOS VERSION  
ZOOM  
AZIMUTH/ELEVATION  
DIRECTION  
XX.X  
FONT VERSION  
XX.X  
ALARM MESSAGE  
(2 SECS)  
COMM  
2400, N, 8, 1  
D ADDRESS  
P ADDRESS  
CM9500 MODE  
32 PRESETS  
PROTOCOL  
1
2
OFF  
OFF  
C
NOTE: For American Dynamics controllers with only 32 presets, switch  
SW3-1 on the dome drive to the ON position. When SW3-1 is ON, preset  
<LABEL POSTIONS>  
RESTORE FACTORY DEFAULTS  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
99 becomes 32  
98 becomes 31  
97 becomes 30  
96 becomes 29  
95 becomes 28  
93 becomes 26  
92 becomes 25  
91 becomes 24  
90 becomes 23  
89 becomes 22  
88 becomes 21  
<ALERT>**  
<CLEAR>  
X.XX  
PRESSURIZED**  
<PASSWORD>  
<ADDITIONAL>  
BACK  
BACK  
EXIT  
BACK  
EXIT  
EXIT  
ADDITIONAL  
LABEL POSITION  
FREE MEMORY  
LAST RESET  
18304  
POWER ON  
0O  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
[ALARM 1-------]  
If the limit stops are turned off, presets 23-26 can be used as regular  
presets.  
Press Iris Close to cancel selection.  
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
FPGA VERSION  
VIDEO LEVEL  
YES  
[ALERT MESSAGE-------]**  
YES  
X
NORMAL  
XXXX-XXXX  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
CAMERA  
ENGLISH X.XX  
LANGUAGE 1  
ITALIANO X.XX  
LANGUAGE 6  
XXX0/-XXXO  
NE  
XXX.XX  
BACK  
EXIT  
MOTION  
PRESETS  
PRESET NUMBER  
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
CAMERA  
PATTERNS  
ZONES  
WINDOW BLANKING  
ALARMS  
AUX  
ALERT**  
CLEAR  
PASSWORD  
ENABLE PASSWORD  
<EDIT PASSWORD>  
POWER UP  
LINE SYNC  
LINE SYNC  
LINE SYNC PHASE  
AUTO FLIP  
ON  
ON  
1
CLEAR ALL ZONES  
OFF  
OUTDOOR  
ON  
ON  
0
STYLE  
GRAY  
RESUME  
OFF  
5
0
AUX 1 MODE  
TOGGLE  
1
REPEAT  
CONSTANT  
ALWAYS ON  
NO  
TYPE OF LIGHTING  
ZONE NUMBER  
* * * ZONE NOT DEFINED * * *  
1
POWER UP ACTION AUTO  
PATTERN NUMBER  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
1
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
SCAN SPEED DEG/S  
PRESET FREEZE FRAME  
CLEAR ALL PRESETS  
DWELL TIME (SECS)  
ACK ACTION  
ACTIVATE AUX  
AUTO FOCUS  
ZOOM LIMIT  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
0
CLEAR ALL PATTERNS  
X176  
BLANK ALL ABOVE  
BLANK ALL BELOW  
OFF  
OFF  
NONE  
25  
AUTO  
CLEAR ALL WINDOW BLANKING  
MEDIUM  
2
<CURRENT READING>  
RESET ALERT  
AUX 2 MODE  
TOGGLE  
1
ZOOM SPEED  
LOW LIGHT LIMIT  
<EDIT ZONE LABEL>  
BACK  
EXIT  
BACK  
EXIT  
<ALARM SETTINGS>  
DWELL TIME (SECS)  
BACK  
EXIT  
BACK  
EXIT  
<SET WINDOWS>  
RESTORE FACTORY DEFAULTS  
<EDIT ZONE>  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
<ADVANCED SETTINGS>  
NO  
OFF  
BACK  
EXIT  
BACK  
EXIT  
BACK  
EXIT  
LIMIT STOPS  
ZONE ENABLED  
ZONE BLANKING  
ON  
BACK  
EXIT  
BACK  
EXIT  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
REFERENCE INFORMATION  
PATTERN USAGE  
REMAINING  
BACK  
EXIT  
0%  
100%  
BACK  
EXIT  
<CLEAR ZONE>  
REFERENCE INFORMATION  
AZIMUTH  
BACK  
EXIT  
-
-
-
-
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
ELEVATION  
ZOOM  
BACK  
EXIT  
CUSTOM CAMERA SETTINGS  
ADVANCED SETTINGS  
SHUTTER SPEED  
ALARM SETTINGS  
CURRENT READING**  
SET WINDOWS  
EDIT THE PASSWORD  
----------  
AUTO  
27  
ALARM NUMBER  
1
TEMPERATURE  
DEWPOINT  
PRESSURE  
REFRESH  
0°C  
0°F  
1
WINDOW NUMBER  
AGC LIMIT  
* If your controller does not have a joystick, use the up or down key.  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
klmnopqrst  
uvwxyz*;:  
OK  
CANCEL  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
LOW  
NONE  
NO  
0°C  
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
AUTO IRIS  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
AUTO SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
AUTO  
66  
8
0°F  
** This setting only applies to Pressurized Spectra III SE dome systems with software  
version 1.25 or higher. Spectra III systems that are not pressurized or pressurized  
systems that do not have dome drive software version 1.25 or higher will not display  
this menu item.  
0.0 PSIG  
0.0 BAR  
SPACE  
BACKSPACE  
ALARM CONTACT  
N/O  
ENABLE WINDOW  
REVERSE  
CLEAR WINDOW  
NO  
ON  
26  
BACK  
EXIT  
ON  
BACK  
EXIT  
482  
BACK  
EXIT  
678  
OFF  
HIGH  
Software version 1.25 or higher includes the software to monitor temperature,  
pressure, and dew point for Pressurized Spectra III SE systems.  
BACK  
EXIT  
C2444M-C (1/04)  
9
 
LANGUAGE  
The language for the on-screen menus is selectable. Available languages include English,  
Spanish, French, German, Italian, and Portuguese. The factory default language is English.  
SPECTRA III  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
To change the display language:  
1. Use the joystick to position the cursor beside LANGUAGE.  
2. Press Iris Open. The cursor moves to the right, beside the current, selected language.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
All on-screen menus are changed to the selected language.  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
11  
 
SYSTEM INFORMATION  
The system Information screen displays dome drive model, software version, available memory,  
SPECTRA III  
and other diagnostic information.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
System settings cannot be changed using this screen. This screen is for reference only.  
Use the following steps to display the System Information screen:  
1. Use the joystick to position the cursor beside SYSTEM INFORMATION.  
2. Press Iris Open. The SYSTEM INFORMATION window opens.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
SYSTEM INFORMATION  
DOME DRIVE MODEL  
DD53M22  
AVAILABLE  
XX.X  
BACK BOX MEMORY  
SOFTWARE VERSION  
BIOS VERSION  
XX.X  
FONT VERSION  
XX.X  
COMM  
2400, N, 8, 1  
D ADDRESS  
P ADDRESS  
CM9500 MODE  
32 PRESETS  
PROTOCOL  
1
2
OFF  
OFF  
C
PRESSURIZED*  
X.XX  
<ADDITIONAL>  
BACK  
EXIT  
ADDITIONAL  
FREE MEMORY  
LAST RESET  
18304  
POWER ON  
0o  
AZIMUTH ZERO OFFSET  
MOTOR ACTIVE  
CAMERA ACTIVE  
FPGA VERSION  
VIDEO LEVEL  
YES  
YES  
X
NORMAL  
XXXX-XXXX  
CAMERA  
LANGUAGE 1  
LANGUAGE 2  
ENGLISH X.XX  
ESPANOL X.XX  
LANGUAGE 3  
LANGUAGE 4  
LANGUAGE 5  
LANGUAGE 6  
BACK  
PORTUGUES X.XX  
DEUTSCH X.XX  
FRANCAIS X.XX  
ITALIANO X.XX  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
12  
C2444M-C (1/04)  
 
DISPLAY SETUP  
Display setup allows you to program how labels are displayed on the monitor. The following  
labels are available:  
SPECTRA III  
LANGUAGE  
ENGLISH  
PRESET LABEL - Identifies preset.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
ZONE LABEL - Identifies zone.  
ZOOM RATIO - Identifies the amount of magnification.  
AZIMUTH1/ELEVATION2 - Amount of pan from 0° and the amount of tilt from 0° horizontal.  
DIRECTION - Displays compass direction.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
ALARM MESSAGE - Displays activated alarm.  
A preset label is displayed when a preset is called. A zone label is displayed when the system  
moves into a zone. The zoom ratio label is displayed when zoom is activated. Azimuth/elevation  
and direction labels are displayed when pan/tilt is activated. An alarm message appears on the  
monitor when an alarm occurs.  
DISPLAY SETUP  
PRESET LABEL  
ZONE LABEL  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
ZOOM  
AZIMUTH/ELEVATION  
DIRECTION  
ALARM MESSAGE  
The following settings are available for each label:  
2 (SECS)  
OFF - Label is not displayed when activated.  
<LABEL POSITIONS>  
CONSTANT - The label is continually displayed when activated.  
2 SECONDS - The label is displayed for 2 seconds after activation.  
5 SECONDS - The label is displayed for 5 seconds after activation.  
10 SECONDS - The label is displayed for 10 seconds after activation.  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
1 Azimuth is the pan angle from 0° to 359°.  
2 Elevation is the tilt position from 0° (horizon) to -90°.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
13  
 
<Label Position>  
Labels can be placed anywhere on the monitor. This feature allows you to customize the  
SPECTRA III  
appearance of your monitor screen.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The following labels are not set at fixed positions:  
PRESET LABEL  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ZONE LABEL  
ALARM 1  
EXIT  
ZOOM RATIO - XXX.XX  
AZIMUTH1/ELEVATION2 - XXX°/-XX°  
DIRECTION - NE  
ALERT MESSAGE3*  
DISPLAY SETUP  
PRESET LABEL  
ZONE LABEL  
ZOOM  
AZIMUTH/ELEVATION  
DIRECTION  
ALARM MESSAGE  
2 (SECS)  
2 (SECS)  
2 (SECS)  
2 (SECS)  
OFF  
To set a label position:  
1. Use the joystick to position the cursor beside a label.  
2. Press Iris Open.  
2 (SECS)  
3. Use the joystick to move the label up, down, left, and/or right.  
4. Press Iris Open.  
<LABEL POSITIONS>  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
5. Repeat steps 1 through 4 to position other labels.  
6. Position the cursor next to Save and Exit. Press Iris Open to save settings and exit  
menu.  
1 Azimuth is the pan angle from 0° to 359°.  
LABEL POSITION  
2 Elevation is the tilt position from 0° (horizon) to -90°.  
[ZONE LABEL-------]  
[PRESET LABEL-------]  
[ALARM 1-------]  
3 The alert message is the warning displayed on the monitor if pressure, temperature, or dew  
point inside the dome reach unacceptable levels.  
[ALERT MESSAGE-------]*  
SAVE AND EXIT  
CANCEL AND EXIT  
HELP  
XXXo/-XXXo  
NE  
XXX.XX  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
14  
C2444M-C (1/04)  
 
DOME SETTINGS  
<Camera>  
TYPE OF LIGHTING  
SPECTRA III  
LANGUAGE  
ENGLISH  
Pelco has calibrated settings that optimize the white balance, and the picture, for indoor and  
outdoor lighting conditions. There are two settings:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
OUTDOOR (default)  
INDOOR  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
AUTO FOCUS  
Auto focus allows the lens to remain in focus during zoom-in, zoom-out, and motion functions.  
There are two auto focus settings:  
ON (default) - If auto focus mode is set to ON, the camera will focus automatically when  
using pan, tilt, and zoom functions.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
OFF - Focus is operated manually. To focus, press the Focus Far or Focus Near button on the  
controller.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
ZOOM LIMIT  
OUTDOOR  
ON  
X176  
ZOOM SPEED  
LOW LIGHT LIMIT  
MEDIUM  
2
<ADVANCED SETTINGS>  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
15  
 
ZOOM LIMIT  
SPECTRA III  
LANGUAGE  
ENGLISH  
Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The default  
setting is 176X.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Cameras with 264X zoom (22X optical zoom and 12X electronic zoom) can be set for 22X, 32X,  
88X, 176X, 220X, or 264X.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
ZOOM SPEED  
Zoom Speed allows the user to define how fast the dome will go from full wide zoom to the 22X  
optical zoom. The default setting is MEDIUM.  
DOME SETTINGS  
Available settings for zoom speed include the following:  
HIGH – 2.4 seconds  
MEDIUM (default) – 3.9 seconds  
LOW – 6.3 seconds  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
NOTE: When using the HIGH setting, the image may be out of focus until zooming stops.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
LOW LIGHT LIMIT  
EXIT  
Low light limit is the maximum duration, in fractions of a second, that the electronic shutter will  
remain open in low light conditions. The default setting is 2.  
Settings include the following:  
2 =1/2 second  
4 = 1/4 second  
8 = 1/8 second  
30 =1/30 second  
60 =1/60 second  
CAMERA  
15 =1/15 second  
TYPE OF LIGHTING  
AUTO FOCUS  
OUTDOOR  
ON  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
X176  
MEDIUM  
2
<ADVANCED SETTINGS>  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
16  
C2444M-C (1/04)  
 
<Advanced Camera Settings>  
SPECTRA III  
SHUTTER SPEED  
LANGUAGE  
ENGLISH  
Shutter speed is the duration of the electronic shutter. Program shutter speed to operate  
automatically (Auto) or manually (Numeric Value).  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
AUTO (default) - The electronic shutter speed is set automatically by the amount of light  
sensed by the camera.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
NUMERIC VALUE - Spectra III SE dome system has several numerical shutter speed  
settings. The higher the number, the faster the electronic shutter.  
The slowest shutter speed setting is 2 = 1/2 second  
The fastest setting is 30,000 = 1/30,000 second  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
Increasing the shutter speed lowers the light sensitivity and reduces  
the streaking of fast moving objects.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<ALERT>*  
<CLEAR>  
NOTE: Set the shutter speed to 100 if you are using an NTSC camera in a 50 Hz  
environment. This will eliminate any flicker that may occur in the picture.  
<PASSWORD>  
BACK  
EXIT  
AGC LIMIT  
The AGC (automatic gain control) Limit adjusts the brightness of the picture. Settings range from  
0 to 40. The brightness increases as the number gets higher.  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
ZOOM LIMIT  
OUTDOOR  
ON  
X176  
ZOOM SPEED  
LOW LIGHT LIMIT  
MEDIUM  
2
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AUTO  
27  
AGC LIMIT  
AUTO IRIS  
AUTO  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
66  
8
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
ON  
482  
678  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
OFF  
HIGH  
BACK  
EXIT  
Quick Programming Guide  
* This setting only applies to Pressurized  
Spectra III SE dome systems with  
software version 1.25 or higher.  
(See page 9)  
C2444M-C (1/04)  
17  
 
AUTO IRIS  
SPECTRA III  
LANGUAGE  
ENGLISH  
Auto iris is the lens function that automatically opens and closes the iris in response to changing  
light conditions.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Program the auto iris to operate automatically or at a user-defined level.  
OFF - Auto iris is disabled, and control is always manual.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
AUTO (default) - The iris is adjusted automatically to produce a constant video output as  
determined by the Auto Iris Level setting.  
EXIT  
NOTE: If auto iris is in the auto mode, it will remain that way until the iris is  
manually opened or closed. The dome will return to auto mode when it is panned or  
tilted more than 15 degrees.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
Auto Iris Level  
Auto Iris Level is the numeric value the auto iris uses to maintain the brightness  
level of the camera. Increase the value to brighten the scene. Decrease the level to  
darken the scene. This setting can be adjusted if the video level in the auto iris  
mode is too bright or too dark.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
NOTE: If backlight compensation is ON, decrease the Auto Iris Level setting.  
Auto Iris Peak  
CAMERA  
Increasing the peak value will cause the auto iris circuit to react more to highlights  
or “peaks” in the picture. Decreasing this value will cause it to use the average  
video level to adjust the iris.  
TYPE OF LIGHTING  
AUTO FOCUS  
ZOOM LIMIT  
ZOOM SPEED  
LOW LIGHT LIMIT  
OUTDOOR  
ON  
X176  
MEDIUM  
2
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AUTO  
27  
AGC LIMIT  
AUTO IRIS  
AUTO  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
66  
8
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
ON  
482  
678  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
OFF  
HIGH  
BACK  
EXIT  
* This setting only applies to Pressurized  
Spectra III SE dome systems with  
software version 1.25 or higher.  
18  
C2444M-C (1/04)  
 
AUTO SHARPNESS  
SPECTRA III  
LANGUAGE  
ENGLISH  
Auto sharpness enhances picture detail by increasing the aperture gain of the camera and  
sharpening the edges in the picture.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
There are two settings:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ON (default) - The camera automatically maintains a normal sharpness mode.  
OFF - The sharpness of the picture is set manually by programming the SHARPNESS LEVEL.  
Sharpness level settings range from 0-31.  
EXIT  
AUTO WHITE BALANCE  
This feature automatically processes the viewed image to retain color balance over a color  
temperature range. The default setting for auto white balance is ON.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
R GAIN - Adjusts the picture output in the red range. As you change the value, you will  
see the color change on your monitor.  
B GAIN - Adjusts the picture output in the blue range. As you change the value, you will  
see the color change on your monitor.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
ZOOM LIMIT  
OUTDOOR  
ON  
X176  
ZOOM SPEED  
LOW LIGHT LIMIT  
MEDIUM  
2
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AUTO  
27  
AGC LIMIT  
AUTO IRIS  
AUTO  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
66  
8
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
ON  
482  
678  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
OFF  
HIGH  
BACK  
EXIT  
Quick Programming Guide  
* This setting only applies to Pressurized  
Spectra III SE dome systems with  
software version 1.25 or higher.  
(See page 9)  
C2444M-C (1/04)  
19  
 
BACKLIGHT COMPENSATION (BLC)  
SPECTRA III  
LANGUAGE  
ENGLISH  
If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette.  
Backlight compensation enhances objects in the center of the picture. The dome uses the center  
of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash  
out to white. The camera will adjust the iris so that the object in the sensitive area is properly  
exposed.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
There are two backlight compensation settings:  
ON - Backlight compensation is activated.  
EXIT  
OFF (default) - Backlight compensation is not activated.  
DOME SETTINGS  
NOTE: If backlight compensation is ON, decrease the Auto Iris setting. Refer to the Auto Iris  
section.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
VIDEO LEVEL  
Set the video output to one of the following:  
NORMAL - 1.0 volt peak-to-peak  
HIGH (default setting) - 1.2 volt peak-to-peak to compensate for losses in video cable.  
EXIT  
CAMERA  
TYPE OF LIGHTING  
AUTO FOCUS  
ZOOM LIMIT  
OUTDOOR  
ON  
X176  
ZOOM SPEED  
LOW LIGHT LIMIT  
MEDIUM  
2
<ADVANCED SETTINGS>  
BACK  
EXIT  
ADVANCED SETTINGS  
SHUTTER SPEED  
AUTO  
27  
AGC LIMIT  
AUTO IRIS  
AUTO  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
66  
8
AUTO SHARPNESS  
SHARPNESS LEVEL  
ON  
26  
AUTO WHITE BALANCE  
R GAIN  
ON  
482  
678  
B GAIN  
BACKLIGHT COMP  
VIDEO LEVEL  
OFF  
HIGH  
BACK  
EXIT  
* This setting only applies to Pressurized  
Spectra III SE dome systems with  
software version 1.25 or higher.  
20  
C2444M-C (1/04)  
 
<Motion Settings>  
AUTO FLIP  
SPECTRA III  
LANGUAGE  
ENGLISH  
When the camera tilts downward and goes just beyond the vertical position, the dome rotates  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you  
continue to hold the joystick in the down position. Once you let go of the joystick after the dome  
rotates, joystick control returns to normal operation. The auto-flip feature is useful for following  
a person who passes directly beneath the dome.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
There are two auto flip modes:  
ON (default) - Auto flip mode is enabled.  
OFF - Auto flip mode is disabled.  
PROPORTIONAL PAN  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the  
amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given  
amount of joystick deflection than at wide zoom settings. This keeps the image from moving too  
fast on the monitor when there is a large amount of zoom.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
There are two proportional pan modes:  
ON (default) - Enables the proportional pan mode.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
OFF - Disables proportional pan mode. The pan speed will not depend on the amount of zoom.  
BACK  
EXIT  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
25  
AUTO  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
21  
 
PARK TIME  
SPECTRA III  
LANGUAGE  
ENGLISH  
This feature allows the dome to begin a specified operation (scan, preset, or pattern) after a  
programmed time of inactivity.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Park time can be programmed from 1 minute to 720 minutes (12 hours), or set to zero, which  
disables this feature. The default setting is zero.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
Park Action  
EXIT  
This feature will define the activity when the dome parks. The following settings are  
available:  
NONE (default) - No action.  
AUTO SCAN - Dome starts auto scan operation.  
RANDOM SCAN - Dome starts random scan operation.  
FRAME SCAN - Dome starts frame scan operation.  
PRESET 1 - Dome goes to preset 1.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
PRESET 8 - Dome goes to preset 8.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
PATTERN 1 - Dome runs pattern 1.  
PATTERN 2 - Dome runs pattern 2.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
PATTERN 3 - Dome runs pattern 3.  
PATTERN 4 - Dome runs pattern 4.  
BACK  
EXIT  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
25  
AUTO  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
22  
C2444M-C (1/04)  
 
SCAN SPEED  
SPECTRA III  
LANGUAGE  
ENGLISH  
Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed  
is adjustable from 1 to 40 degrees per second through the programming menu. The default  
setting is 25 degrees per second.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
PRESET FREEZE FRAME  
This feature freezes the scene on the monitor when going to a preset. This allows for smooth  
transition from one preset scene to another. Preset freeze frame also reduces bandwidth when  
used with digital network systems such as PelcoNet™ and guarantees that blanked areas will not  
be revealed when going to a preset.  
EXIT  
There are three preset freeze frame settings:  
DOME SETTINGS  
ON - The image on the screen freezes when a preset is called. When the dome reaches the  
preset, the image is unfrozen and the preset scene is displayed.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
OFF - The image is never frozen.  
AUTO (default) - Freeze frame is turned on automatically if window blanking is ON. If  
window blanking is OFF, freeze frame is off.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
25  
AUTO  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
23  
 
LIMIT STOPS  
SPECTRA III  
LANGUAGE  
ENGLISH  
Limit stops are programmable stops that limit the pan range of the dome. There must be two  
limits, a left and a right, to define an area.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
There are two types of limit stops:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
MANUAL - A manual (joystick) pan operation stops when a limit stop is reached.  
SCAN - The dome reverses direction during random, frame, or auto scanning when a limit  
stop is reached.  
EXIT  
To set manual or scan stops:  
1. Use the joystick to position the cursor beside SET MANUAL STOPS or SET SCAN  
STOPS.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
2. Press Iris Open.  
3. Follow the directions displayed on the monitor.  
NOTE: In order for the manual or scan stops to work, the LIMIT STOPS setting must be ON.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
To clear manual or scan stops:  
1. Use the joystick to position the cursor beside CLEAR MANUAL STOPS or CLEAR SCAN  
STOPS.  
BACK  
EXIT  
2. Press Iris Open.  
3. Follow the directions displayed on the monitor.  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
25  
AUTO  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
24  
C2444M-C (1/04)  
 
AZIMUTH ZERO  
SPECTRA III  
LANGUAGE  
ENGLISH  
Azimuth is the pan angle from 0° to 359°. Azimuth zero is the pan position you specify to be the  
0° point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass  
readings are based on the set Azimuth Zero point.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
To program azimuth zero:  
1. Use the joystick to position the cursor beside SET AZIMUTH ZERO.  
2. Press Iris Open.  
EXIT  
3. Follow the directions displayed on the monitor.  
To clear azimuth zero:  
DOME SETTINGS  
1. Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO.  
2. Press Iris Open.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
3. Follow the directions displayed on the monitor.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
MOTION  
AUTO FLIP  
ON  
ON  
PROPORTIONAL PAN  
PARK TIME (MINUTES)  
PARK ACTION  
0
NONE  
25  
AUTO  
SCAN SPEED (DEG/S)  
PRESET FREEZE FRAME  
LIMIT STOPS  
ON  
<SET MANUAL STOPS>  
<CLEAR MANUAL STOPS>  
<SET SCAN STOPS>  
<CLEAR SCAN STOPS>  
<SET AZIMUTH ZERO>  
<CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
REFERENCE INFORMATION  
MANUAL LIMITS SET  
SCAN LIMITS SET  
NO  
NO  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
25  
 
<Power Up>  
SPECTRA III  
POWER UP ACTION  
LANGUAGE  
ENGLISH  
This setting defines a specific activity (scan, preset, pattern) to be performed in the event the  
power to the dome is cycled.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The following settings are available:  
RESET CAMERA  
NONE - No action.  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
AUTO (default) - The dome resumes its prior activity or direction before the power outage.  
AUTO SCAN - Dome starts auto scan operation.  
RANDOM SCAN - Dome starts random scan operation.  
FRAME SCAN - Dome starts frame scan operation.  
PRESET 1 - Dome goes to preset 1.  
EXIT  
DOME SETTINGS  
PRESET 8 - Dome goes to preset 8.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
PATTERN 1 - Dome runs pattern 1.  
PATTERN 2 - Dome runs pattern 2.  
PATTERN 3 - Dome runs pattern 3.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
PATTERN 4 - Dome runs pattern 4.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
POWER UP  
POWER UP ACTION  
AUTO  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
26  
C2444M-C (1/04)  
 
<Line Sync>  
Line sync refers to a programmable function that allows you to synchronize all cameras within a  
SPECTRA III  
matrix system.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
NOTE: Spectra III SE automatically senses V-sync input. No line sync setup is required for Pelco  
control systems that provide a V-sync signal.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
For matrix systems that do not output V-sync, there are two settings for line synchronization:  
ON (default) - Adjusts the phase of the line sync to synchronize input power. LINE SYNC  
PHASE settings range from 0-359 degrees.  
OFF - The dome synchronizes to an internal clock.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
LINE SYNC  
LINE SYNC  
LINE SYNC PHASE  
ON  
0
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
27  
 
<Presets>  
The Spectra III SE dome system has 80 programmable preset positions. Each preset can be  
SPECTRA III  
programmed to use pan, tilt, and all programmable camera settings.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The presets are numbered 1-32 and 35-82. Presets 33 and 34 are fixed commands that cannot be  
programmed. Preset 33 is the “flip” command, which will pan the dome drive 180 degrees.  
Preset 34 is the “pan zero” command, which will direct the dome drive to the factory-determined  
zero reference point.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
Use the following steps to program a preset.  
1. Select the preset number:  
a. Use the joystick to position the cursor beside PRESET NUMBER. Press Iris Open.  
The cursor moves to the right.  
DOME SETTINGS  
b. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
2. Edit the preset label:  
a. Use the joystick to position the cursor beside EDIT PRESET LABEL.  
b. Press Iris Open. The following appears on the monitor:  
LABEL FOR PRESET  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
PRESET NUMBER ------  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
OK  
CANCEL  
BACK  
EXIT  
SPACE  
BACKSPACE  
klmnopqrst  
uvwxyz*;:  
PRESETS  
c. Use the joystick to position the cursor beside a character. Press Iris Open to enter  
selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris  
Open.  
PRESET NUMBER  
1
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
d. When label is completed, move the cursor to OK. Press Iris Open to return to the  
Preset menu.  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
REFERENCE INFORMATION  
AZIMUTH  
-
-
-
-
ELEVATION  
ZOOM RATIO  
CUSTOM CAMERA SETTINGS  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
28  
C2444M-C (1/04)  
 
3. Edit the preset scene:  
SPECTRA III  
a. Use the joystick to position the cursor beside EDIT PRESET SCENE.  
b. Press Iris Open.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
c. Follow the directions displayed on the monitor.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
4. Edit preset camera settings:  
a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS.  
EXIT  
b. Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor. Refer  
to the Camera and Advanced Camera Settings sections of this manual to change  
preset camera settings.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
NOTE: You can copy camera settings from one preset to another preset. To copy camera  
settings do the following:  
1. Use the joystick to position the cursor beside COPY CAMERA SETTINGS.  
2. Press Iris Open. The cursor moves to the right.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
PRESETS  
PRESET NUMBER  
1
* * * PRESET NOT DEFINED * * *  
<EDIT PRESET LABEL>  
<EDIT PRESET SCENE>  
<EDIT CAMERA SETTINGS>  
<CLEAR PRESET>  
<CLEAR CAMERA SETTINGS>  
BACK  
EXIT  
REFERENCE INFORMATION  
AZIMUTH  
-
-
-
-
ELEVATION  
ZOOM RATIO  
CUSTOM CAMERA SETTINGS  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
29  
 
<Patterns>  
A pattern is a memorized, repeating, series of pan, tilt, zoom and preset functions that can be  
SPECTRA III  
recalled with a command from a controller or automatically by a programmed function (alarm,  
park or power-up).  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
The Spectra III SE can handle up to four user-defined patterns. Pattern length is based upon  
memory usage rather than a fixed amount of time. The complexity of a pattern will determine  
the amount of storage available to program other patterns.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
To program a pattern:  
1. Use the joystick to position the cursor beside PATTERN NUMBER. Press Iris Open. The  
cursor moves to the right.  
2. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
3. Use the joystick to position the cursor beside PROGRAM PATTERN.  
4. Press Iris Open. The Patterns programming window appears on the monitor.  
5. Follow the directions displayed on the monitor.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
After a pattern is programmed, the remaining storage percentage is displayed on the screen.  
This is the amount of memory available to program the remaining patterns.  
<ALERT>*  
<CLEAR>  
To clear a pattern:  
<PASSWORD>  
1. Use the joystick to position the cursor beside CLEAR PATTERN.  
2. Press Iris Open.  
BACK  
EXIT  
3. Follow the directions displayed on the monitor.  
NOTE: When programming one or more presets within a pattern use the normal controller  
PATTERNS  
commands to Call a Preset.  
PATTERN NUMBER  
<PROGRAM PATTERN>  
<CLEAR PATTERN>  
1
NOTE: Not all controllers can start all four patterns. However, any of the four patterns can be  
automatically started with park, power-up, and alarm functions.  
BACK  
EXIT  
REFERENCE INFORMATION  
PATTERN USAGE  
REMAINING  
0%  
100%  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
30  
C2444M-C (1/04)  
 
<Zones>  
A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The Spectra  
SPECTRA III  
dome system is capable of eight zones, each with a 20-character label.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
To program a zone:  
1. Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open the  
cursor moves to the right.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
2. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
3. Use the joystick to position the cursor beside EDIT ZONE.  
EXIT  
4. Press Iris Open. The Zone programming window appears on the monitor.  
5. Follow the directions displayed on the monitor. After the left and right limit stops are  
set, the Zones menu reappears with the ZONE ENABLED option set to YES.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
To edit a zone label:  
1. Use the joystick to position the cursor beside EDIT ZONE LABEL.  
2. Press Iris Open. The following appears on the monitor:  
3. Use the joystick to position the cursor beside a character. Press Iris Open to enter  
selection. To clear a character, position the cursor beside BACKSPACE, and then press  
Iris Open.  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
LABEL FOR PRESET  
BACK  
EXIT  
PRESET NUMBER ------  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
abcdefghij  
OK  
CANCEL  
SPACE  
BACKSPACE  
klmnopqrst  
uvwxyz*;:  
ZONES  
ZONE NUMBER  
1
* * * ZONE NOT DEFINED * * *  
4. When the label is completed, move the cursor the OK. Press Iris Open to return to the  
Zones menu.  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
ZONE ENABLED  
ZONE BLANKING  
NO  
OFF  
To disable a zone (a zone is enabled automatically when it is programmed) or to blank a zone:  
1. Move the cursor beside ZONE ENABLED or ZONE BLANKING.  
<CLEAR ZONE>  
BACK  
EXIT  
2. Press Iris Open. The cursor moves to the right.  
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
To clear a zone:  
1. Use the joystick to position the cursor beside CLEAR ZONE.  
2. Press Iris Open. Follow the instructions on the screen.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
31  
 
<Window Blanking>  
Window blanking allows a user to program up to eight, four-sided, user-defined areas that  
cannot be viewed by the operator of the dome system. A blanked area will move with pan and  
tilt functions and automatically adjust in size as the lens zooms telephoto and wide.  
SPECTRA III  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Spectra III SE has two style modes for window blanking, GRAY and SMEAR. If style is set to  
gray, the blanked area is covered with a solid gray window. If smear is selected images behind  
the window will be noticeable but not distinguishable.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
To set a window blanking area:  
1. Use the joystick to position the cursor beside WINDOW BLANKING. Press Iris Open.  
The WINDOW BLANKING menu appears on the screen.  
DOME SETTINGS  
2. Move the joystick to position the cursor beside SET WINDOWS. Press Iris Open to enter.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
3. Position the cursor beside WINDOW NUMBER. Press Iris Open. The cursor moves to  
the right.  
4. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
5. Use the joystick to position the cursor beside EDIT WINDOW LOCATION. Press Iris  
Open, and then follow the instructions that appear on the screen.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
NOTE: Use the inside corner of the window selection  
tool as a guide when selecting the upper left, upper right,  
bottom right, and bottom left corners of the window.  
WINDOW BLANKING  
STYLE  
NOTE: Set windows are not visible when editing a new window location.  
GRAY  
BLANK ALL ABOVE  
BLANK ALL BELOW  
OFF  
OFF  
When all four corners are set, the SET WINDOWS menu reappears, the blanked area  
is displayed, and the ENABLE WINDOW option is set to YES.  
<SET WINDOWS>  
BACK  
EXIT  
SET WINDOWS  
WINDOW NUMBER  
1
<EDIT WINDOW LOCATION>  
<EDIT WINDOW ZOOM>  
ENABLE WINDOW  
REVERSE  
NO  
CLEAR WINDOW  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
32  
C2444M-C (1/04)  
 
6. The blanked area can be programmed to turn on or off at a specified zoom point. To set the  
zoom point:  
a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press  
Iris Open.  
b. Zoom in to the point where you want window blanking to turn on. Press Iris Open to  
set the zoom point.  
TIP: Since the area is already blanked out, it may be difficult to determine when you want  
window blanking to turn on. Reverse the window before setting the zoom point. When  
finished reverse the window again to blank out the area.  
IMPORTANT: Increase the  
size of the window if any part  
of the blanked area is  
revealed during pan, tilt, and  
zoom operations.  
Window Blanking Disabled  
Window Blanking Enabled  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
33  
 
REVERSE  
A blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the  
blanking area remain visible. Reversing the window a second time will return it to its original condition.  
CLEAR WINDOW  
All areas that have been set for window blanking are cleared.  
BLANK ALL ABOVE/BLANK ALL BELOW  
Blank All Above and Blank All Below add additional flexibility to setting up privacy areas. These settings are ideal for applications  
where a complete pan location needs to be blanked.  
Blank All Above  
Blank All Below  
Blanks everything above a user-defined tilt angle. A blanked  
band will appear at the top of the screen. The following  
settings are available:  
Blanks everything below a user-defined tilt angle. A blanked  
circle will appear below the specified angle. The following  
settings are available:  
OFF (default) - No blanking  
OFF (default) - No blanking  
0 - Blanks area from horizon to 2° below horizon  
-10 - Blanks area from horizon to 10° below horizon  
-20 - Blanks area from horizon to 20° below horizon  
-30 - Blanks area from horizon to 30° below horizon  
-40 - Blanks area from horizon to 40° below horizon  
-50 - Blanks area from horizon to 50° below horizon  
-60 - Blanks area from horizon to 60° below horizon  
-70 - Blanks area from horizon to 70° below horizon  
-80 - Blanks area from horizon to 80° below horizon  
0 - Blanks area from 2° to 92° below horizon  
-10 - Blanks area from 10° to 92° below horizon  
-20 - Blanks area from 20° to 92° below horizon  
-30 - Blanks area from 30° to 92° below horizon  
-40 - Blanks area from 40° to 92° below horizon  
-50 - Blanks area from 50° to 92° below horizon  
-60 - Blanks area from 60° to 92° below horizon  
-70 - Blanks area from 70° to 92° below horizon  
-80 - Blanks area from 80° to 92° below horizon  
HORIZON  
CAMERA  
30  
34  
C2444M-C (1/04)  
 
<Alarms>  
The Spectra III SE dome has seven alarm inputs, which can be programmed as high, medium or  
SPECTRA III  
low priority. When an alarm is received, an input signal to the dome triggers the user-defined  
action (go to preset, run pattern, etc.) programmed for the alarm.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
There are three global alarm settings:  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
RESUME - This mode lets the dome resume its previous activity (scan, pattern, or previous  
position) after all alarms are cleared.  
EXIT  
SEQUENCE - This is the time the dome will perform an alarm activity when more than one  
alarm of the same priority occurs at the same time.  
RESET DELAY - This is the amount of time the dome considers the alarm to be active after  
it has physically cleared.  
DOME SETTINGS  
Use the following steps to program alarm settings.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
1. Use the joystick to position the cursor beside ALARM SETTINGS. Press Iris Open.  
2. Select the alarm number:  
a. Use the joystick to position the cursor beside ALARM NUMBER.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view selections. Press Iris Open to enter selection.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
(Continued on next page)  
ALARMS  
RESUME  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
OFF  
5
0
<ALARM SETTINGS>  
BACK  
EXIT  
ALARM SETTINGS  
ALARM NUMBER  
1
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
LOW  
NONE  
NO  
ALARM CONTACT  
N/O  
BACK  
EXIT  
Quick Programming Guide  
* This setting only applies to Pressurized  
Spectra III SE dome systems with  
software version 1.25 or higher.  
(See page 9)  
C2444M-C (1/04)  
35  
 
3. Select the alarm priority:  
SPECTRA III  
a. Use the joystick to position the cursor beside ALARM PRIORITY.  
b. Press Iris Open. The cursor moves to the right.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
c. Move the joystick up or down to view the available selections. Available settings  
include HIGH, MEDIUM, and LOW (default). If multiple alarms with different priorities  
are active at the same time, the dome will only go to the alarms with the highest  
priority.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
d. Press Iris Open to enter selection.  
NOTE: HIGH - Alarm action takes highest priority and will override manual pan, tilt,  
and zoom control.  
DOME SETTINGS  
MEDIUM/LOW - Alarm action will not occur if an alarm occurs during manual  
pan, tilt, and zoom control.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
4. Set the alarm action:  
a. Use the joystick to position the cursor beside ALARM ACTION.  
b. Press Iris Open. The cursor moves to the right.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
c. Move the joystick up or down to view the available selections. The following are the  
settings for alarm action:  
BACK  
EXIT  
NONE - No action when alarm is triggered.  
PRESET - Dome goes to the preset that is the same as the alarm number. Preset  
1 will go to Alarm 1.  
PATTERN 1 - Dome runs pattern 1 when alarm is triggered.  
PATTERN 2 - Dome runs pattern 2 when alarm is triggered.  
PATTERN 3 - Dome runs pattern 3 when alarm is triggered.  
PATTERN 4 - Dome runs pattern 4 when alarm is triggered.  
AUTO SCAN - Dome starts auto scan operation when alarm is triggered.  
RANDOM SCAN - Dome starts random scan operation when alarm is triggered.  
FRAME SCAN - Dome starts frame scan operation when alarm is triggered.  
d. Press Iris Open to enter selection.  
ALARMS  
RESUME  
OFF  
5
0
SEQUENCE (SECS)  
RESET DELAY (SECS)  
<ALARM SETTINGS>  
BACK  
EXIT  
ALARM SETTINGS  
ALARM NUMBER  
1
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
LOW  
NONE  
NO  
ALARM CONTACT  
N/O  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
36  
C2444M-C (1/04)  
 
5. Set the auxiliary to activate:  
SPECTRA III  
a. Use the joystick to position the cursor beside ACTIVATE AUX.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view the following available selections.  
NO (default) - Not activated.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
1 - An alarm action will close AUX 1.  
2 - An alarm action will close AUX 2.  
d. Press Iris Open to enter selection.  
NOTE: The AUX 1/AUX2 will stop when all the alarms assigned to it have cleared. If  
the AUX1/AUX is set up as momentary, then it will be activated each time a new  
alarm is activated.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
6. Set the alarm contact:  
a. Use the joystick to position the cursor beside ALARM CONTACT.  
b. Press Iris Open. The cursor moves to the right.  
c. Move the joystick up or down to view the following available selections.  
N/O (default) - Normally open  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
N/C - Normally closed  
d. Press Iris Open to enter selection.  
ALARMS  
RESUME  
SEQUENCE (SECS)  
RESET DELAY (SECS)  
OFF  
5
0
<ALARM SETTINGS>  
BACK  
EXIT  
ALARM SETTINGS  
ALARM NUMBER  
1
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
LOW  
NONE  
NO  
ALARM CONTACT  
N/O  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
37  
 
<Aux>  
SPECTRA III  
An auxiliary output is a programmable signal from the dome back box that can trigger another  
device to operate. An auxiliary output is programmable to trigger from an alarm or from a  
controller.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
An AUX 1 command from the controller will activate the relay in the dome and operate the  
device that is connected to the relay. The output of AUX 1 can be connected to the alarm input of  
a system switch to activate automatic monitor switching and recording.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
An AUX 2 command from the controller will place a ground at the output of AUX 2 to operate the  
device that is connected to it.  
The following are the available AUX MODE settings:  
DOME SETTINGS  
TOGGLE (default) - Changes the state of the auxiliary output every time an AUX command  
is received from the controller.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
LATCHING - Must receive an AUX ON/AUX OFF command from the controller to turn the  
auxiliary output on/off.  
MOMENTARY - An AUX ON command from the controller turns the auxiliary output on for  
the programmed DWELL TIME. The auxiliary output will automatically turn  
off when the dwell time is finished.  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
AUX  
AUX 1 MODE  
DWELL TIME (SECS)  
AUX 2 MODE  
TOGGLE  
1
TOGGLE  
1
DWELL TIME (SECS)  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
38  
C2444M-C (1/04)  
 
<Alert>  
SPECTRA III  
NOTE: The Alert section only applies to Pressurized Spectra III SE dome systems with software  
version 1.25 or higher. Spectra III SE systems that are not pressurized or pressurized systems  
that do not have dome drive software version 1.25 or higher will not display this menu item.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT  
Software version 1.25 or higher includes the software to monitor temperature, pressure, and  
dew point for Pressurized Spectra III SE systems.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
Sensors strategically placed inside the pressurized dome system continually monitor pressure,  
temperature, and dew point. If internal conditions reach unacceptable levels, an alert message  
appears on the screen describing the alert condition. Example: If pressure drops below 1 psig,  
“LOW PRESSURE” is displayed on the monitor.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
The following system conditions will trigger an alert message:  
System Condition  
Alert Message  
Temperature is above 140°F (60°C)  
Temperature is below -40°F (-40°C).  
Pressure is above 11 PSIG.  
Pressure is below 1 PSIG  
HIGH TEMPERATURE  
LOW TEMPERATURE  
HIGH PRESSURE  
LOW PRESSURE  
<ALERT>  
<CLEAR>  
<PASSWORD>  
The difference between the temperature and the dew point is  
less than or equal to 3°C.  
DEW POINT (HIGH  
HUMIDITY)  
BACK  
EXIT  
The alert message will be repeatedly displayed until the system controller acknowledges the  
alert condition by selecting ACK ALERT in the main menu. Once acknowledged, the alert  
message changes to the programmed acknowledge action (ACK ACTION). If the alert condition  
remains active after a period of time, the alert message reappears on the monitor, restarting the  
alert message cycle. This cycle will continue to repeat until the alert condition is resolved.  
ALERT  
REPEAT  
ACK ACTION  
CONSTANT  
ALWAYS ON  
NO  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
REPEAT  
This setting programs how often an alert message is repeatedly displayed until the system  
controller acknowledges the alert condition. The following are the settings for REPEAT:  
BACK  
EXIT  
CONSTANT - The alert message is continuously displayed on the monitor until acknowl-  
edged.  
15 MIN - The alert message is displayed every 15 minutes for a 15-second duration until  
acknowledged.  
30 MIN - The alert message is displayed every 30 minutes for a 15-second duration until  
acknowledged.  
60 MIN - The alert message is displayed every 60 minutes for a 15-second duration until  
acknowledged.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
39  
 
ACK ACTION  
SPECTRA III  
Acknowledge action programs the alert label behavior after the alert condition has been  
acknowledged. The following settings are available for ACK ACTION:  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT  
ALWAYS ON - The alert label is displayed until alert conditions are cleared.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
OFF 8 HRS - The alert label is turned off for 8 hours. Label returns after 8 hours if the alert  
condition persists.  
OFF 24 HRS - The alert label is turned off for 24 hours. Label returns after 24 hours if the  
alert condition persists.  
DOME SETTINGS  
OFF 48 HRS - The alert label is turned off for 48 hours. Label returns after 48 hours if the  
alert condition persists.  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
ACTIVATE AUX  
This setting activates an auxiliary when an alert condition exists. ACTIVATE AUX settings include  
the following:  
NO (default) - Not activated.  
1 - An alert condition will close AUX 1.  
2 - An alert condition will close AUX 2.  
<ALERT>  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
CURRENT READING  
The Current Reading menu displays the existing status of temperature, pressure, and dew point  
inside the dome system. An arrow displayed to the left of a menu item denotes that an alert  
condition exists. An up arrow indicates the reading is over the threshold. A down arrow  
indicates the reading is below the threshold.  
ALERT  
REPEAT  
ACK ACTION  
CONSTANT  
ALWAYS ON  
NO  
ACTIVATE AUX  
<CURRENT READING>  
RESET ALERT  
The high temperature alert occurs if the temperature is above 140°F (60°C).  
The low temperature alert occurs if the temperature is below -40°F (-40°C).  
The high pressure alert occurs if the pressure is above 11 PSIG.  
The low pressure alert occurs if the pressure is below 1 PSIG.  
BACK  
EXIT  
The dew point (high humidity) alert occurs if the difference between the temperature and  
the dew point is less than or equal to 3°C.  
NOTE: The normal operating temperature inside the unit will be greater than the temperature  
outside the back box due to the heat emitted by the system’s electronics.  
CURRENT READING  
TEMPERATURE  
DEWPOINT  
PRESSURE  
REFRESH  
0°C  
0°F  
0°C  
0°F  
ALERT RESET  
0.0 PSIG  
0.0 BAR  
Alert reset clears the alert condition and removes the alert label from the monitor. The system  
automatically checks internal conditions 60 seconds after reset. If conditions are still unaccept-  
able, the alert label reappears on the screen indicating further corrective action is required.  
BACK  
EXIT  
40  
C2444M-C (1/04)  
 
<Clear>  
Use this setting to clear user-defined settings or return the dome to factory default settings.  
SPECTRA III  
LANGUAGE  
ENGLISH  
The following are the available CLEAR settings:  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
ALL ZONES - Clears all zones. To clear a single zone, refer to the Zones section.  
ALL PRESETS - Clears all presets. To clear a single preset, refer to the Presets section.  
ALL PATTERNS - Clears all patterns. To clear a single patterns, refer to the Patterns section.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
ALL WINDOW BLANKING - Clears all blanked windows. To clear a single blanked window,  
refer to the Window Blanking section.  
EXIT  
RESTORE FACTORY DEFAULTS - Restores all camera settings to factory default settings.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
CLEAR  
CLEAR ALL ZONES  
CLEAR ALL PRESETS  
CLEAR ALL PATTERNS  
CLEAR ALL WINDOW BLANKING  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
41  
 
<Password>  
Spectra III SE features password protection to prevent unauthorized changes to the dome  
SPECTRA III  
settings. An operator can open the System Information and Display Setup Screens, but cannot  
access any of the Dome Settings menus.  
LANGUAGE  
ENGLISH  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
Controller/keyboard commands cannot override password-protected settings. If a keyboard is  
used to set a preset, pattern, or zone, the Enter Password screen appears on the monitor.  
The password must be entered before programming can continue.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
At least one character must be entered to create a valid password.  
DOME SETTINGS  
<CAMERA>  
<MOTION>  
<POWER UP>  
<LINE SYNC>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<WINDOW BLANKING>  
<ALARMS>  
<AUX>  
<ALERT>*  
<CLEAR>  
<PASSWORD>  
BACK  
EXIT  
PASSWORD  
ENABLE PASSWORD  
<EDIT PASSWORD>  
OFF  
BACK  
EXIT  
EDIT THE PASSWORD  
----------  
1234567890  
OK  
CANCEL  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZ.,-/  
SPACE  
abcdefghij  
klmnopqrst  
uvwxyz*;:  
BACKSPACE  
* This setting only applies to Pressurized  
Spectra III SE dome systems with  
software version 1.25 or higher.  
42  
C2444M-C (1/04)  
 
RESET, CYCLE POWER, REBOOT  
RESET CAMERA  
SPECTRA III  
LANGUAGE  
ENGLISH  
Use this function to reset all camera settings to factory default parameters.  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME SETTINGS>  
ACK ALERT*  
CYCLE CAMERA POWER  
If the camera is not operating or if you lose camera control, cycle camera power. Cycling camera  
power resets the camera but does not change any saved camera settings.  
RESET CAMERA  
CYCLE CAMERA POWER  
REBOOT SYSTEM  
EXIT  
REBOOT SYSTEM  
Reboot the system if it is not operating or if there is no control. Rebooting the system will cycle  
dome and camera power without changing programmed dome settings.  
* This setting only applies to  
Pressurized Spectra III SE dome  
systems with software version  
1.25 or higher.  
Quick Programming Guide  
(See page 9)  
C2444M-C (1/04)  
43  
 
SOFTWARE/LANGUAGE FILE UPLOAD  
The RJ-45 data port of the dome drive allows access for on-site setup, testing, and uploading of  
revised operating software and language files. A Pelco field service tool is required to perform  
these operations. Field service tools include Pelco’s remote monitor kit (IPS-RMK), remote data  
port box (IPS-RDPE-2), and remote monitor cable (IPS-CABLE).  
For instructions on how to upload revised operating software and language files refer to the  
Installation/Operation manual supplied with the field service tool.  
NOTE: Only perform software uploads when necessary. Software uploads do not need to be  
performed if the dome system is operating properly.  
UPLOAD ICON  
During a software/language file upload, an icon will appear on the monitor to indicate data is  
being transferred to the Spectra dome system (refer to the figure below). The default setting for  
data transmission is 115.2 KB per second. Noisy and long-run connections will slow the  
transmission rate.  
Upload Icon  
44  
C2444M-C (1/04)  
 
SPECIFICATIONS  
DD53C22  
Signal Format  
NTSC  
Scanning System  
Image Sensor  
2:1 Interlace  
1/4-inch CCD  
Effective pixels  
Horizontal Resolution  
Lens  
768 (H) X 494 (V)  
>470 TV lines  
F1.6 (f=4~88 mm optical, 22X optical zoom, 12X electronic zoom)  
3.9 seconds  
Zoom Speed  
Horizontal Angle of view  
Focus  
Maximum Sensitivity at 35 IRE  
Sync System  
White Balance  
Shutter Speed  
47° at 4 mm wide zoom; 2.2° at 88 mm telephoto zoom  
Automatic with manual override  
0.02 lux at 1/2 sec. shutter speed  
Internal/AC line lock, phase adjustable via remote control, V-sync  
Automatic with manual override  
Automatic (electronic iris)/manual  
1/2 ~ 1/30,000  
Iris Control  
Gain Control  
Automatic iris control with manual override  
Automatic/off  
Video Output  
1 Vp-p, 75 ohms  
Video Signal to Noise  
>50 dB  
DD53C22-X  
Signal Format  
PAL  
Scanning System  
Image Sensor  
2:1 Interlace  
1/4-inch CCD  
Effective pixels  
Horizontal Resolution  
Lens  
752 (H) X 582 (V)  
>460 TV lines  
F1.6 (f=4~88 mm optical, 22X optical zoom, 12X electronic zoom)  
3.9 seconds  
Zoom Speed  
Horizontal Angle of view  
Focus  
Maximum Sensitivity at 35 IRE  
Sync System  
White Balance  
Shutter Speed  
47° at 4 mm wide zoom; 2.2° at 88 mm telephoto zoom  
Automatic with manual override  
0.02 lux at 1/1.5 sec. shutter speed  
Internal/AC line lock, phase adjustable via remote control, V-sync  
Automatic with manual override  
Automatic (electronic iris)/manual  
1/1.5 ~ 1/30,000  
Iris Control  
Gain Control  
Automatic iris control with manual override  
Automatic/off  
Video Output  
1 Vp-p, 75 ohms  
Video Signal to Noise  
>50 dB  
C2444M-C (1/04)  
45  
 
REGULATORY NOTICES  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not  
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined  
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following  
measures:  
•
•
•
•
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.”  
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.  
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to  
operate this equipment under Federal Communications Commission’s rules.  
REVISION HISTORY  
Manual #  
C2444M  
C2444M-A  
C2444M-B  
C2444M-C  
Date  
2/02  
11/02  
2/03  
1/04  
Comments  
Original version.  
Revised Quick Start Guide.  
Manual revised to include features of software version 1.2.  
Added alert feature. Updated menus and instructions.  
® Pelco, the Pelco logo, and Genex are registered trademarks of Pelco.  
™ Spectra III, PelcoNet, and LowLight are trademarks of Pelco.  
© Copyright 2004, Pelco.  
All rights reserved.  
46  
C2444M-C (1/04)  
 
World Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
www.pelco.com  
ISO9001  
Orangeburg, New York | Las Vegas, Nevada | Eindhoven, The Netherlands | Wokingham, United Kingdom | Montreal, Canada | Singapore  
 

Peavey Portable Speaker 1580 User Manual
Pentax Digital Camera OptioWP User Manual
Philips Indoor Furnishings 34617 48 16 User Manual
Philips MP3 Player 7FF2CWO User Manual
Philips Work Light 57904 87 16 User Manual
Philips Work Light SR T5 User Manual
Pioneer Stereo Amplifier S A9700V User Manual
Poulan Trimmer 952711961 User Manual
ProForm Home Gym PFANBE14250 User Manual
Proson Home Theater System rv2600 dts User Manual