®
SB19/SB1900 Series
Discreet Surveillance Enclosures
Installation/Operation Manual
C467M-D (5/95)
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827
INSTALLATION AND OPERATION MANUAL
DISCREET SURVEILLANCE ENCLOSURES:
MODEL SB19/SB1900 SERIES
CAUTION
This device is designed to operate at 24VAC power.
MODEL SB19-1/SB1901 SERIES
MODEL DD1900 SERIES
Input voltage must not exceed 28 volts or drop be-
low 22 volts or else damage to the motors will occur.
Should you need assistance with this or any Pelco
product, please call 1-800-298-9100or 1-559-
292-1981.
1.0 WARNINGS
Priortoinstallationanduseofthisproduct,thefollowing
WARNINGS should be observed.
3. OnlyusereplacementpartsrecommendedbyPelco.
4. After replacement/repair of this unit’s electrical
components, conduct a resistance measurement
betweenlineandexposedpartstoverifytheexposed
parts have not been connected to line circuitry.
1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.
2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be
installed where exposed to rain and moisture.
5. The installation method and materials should be
capable of supporting four (4) times the weight of
theenclosure,pan/tilt,cameraandlenscombination.
The product may bear the following
marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TOREDUCETHERISKOFELECTRICAL
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Please thoroughly familiarize yourself with the information in this manual
prior to installation and operation.
Pelco Manual C467M-D (5/95)
1
2.0 SCOPE
NOTE: The following are the cable require-
ments. A relay box (RB24) is available to
extend the operating distance. Consult the
factory for details.
The information contained within this manual covers
the SB19/SB1900 Series of Discreet Surveillance En-
closures.
3.0 DESCRIPTION
Non-PP Models
The SB19 is a low profile, hemisphere, discreet sur-
veillance dome for CCD type cameras designed for ease
of installation, relocation, and servicing in hard ceiling
applications or in a standard 2' x 2' or 2' x 4' suspended
ceiling grid.
12 Conductors
13 Conductors*
20 Awg
18 Awg
16 Awg
190 ft (57.91 m)
300 ft (91.44 m)
480 ft (146.3 m)
380 ft (115.82 m)
600 ft (182.88 m)
960 ft (292.61 m)
The black opaque lower dome effectively conceals the
camera while providing an inconspicuous viewing win-
dow. The dome mounts directly to the pan/tilt (or fixed
camera mount), thus keeping the viewing window and
camera aligned.
Models with PP
18 Conductors
19 Conductors*
20 Awg
18 Awg
16 Awg
190 ft (57.91 m)
300 ft (91.44 m)
480 ft (146.3 m)
380 ft (115.82 m)
600 ft (182.88 m)
960 ft (292.61 m)
To simplify installation even further, Pelco offers
system packages with factory installed standard com-
ponents from its regular product line. Options include
a 24 VAC pan/tilt with factory pre-wired feed-through
for all control functions (i.e., pan/tilt, motorized zoom
lens, camera power (24 VAC) and video), continuous
360° pan rotation, and a position feedback package for
presets.
*Using 2 conductor common.
Calculations are based on a 10% cable loss with both
motors running.
4.2 WIRING INSTRUCTIONS
The dome and camera assembly rotate at a speed of 24
degrees/second for complete 360 degree surveillance
coverage.
The SB1900 and SB1900-SL include a pan/tilt which
is pre-wired for all control functions (pan/tilt, motor-
ized zoom lens, camera power (24 VAC), and video).
All connections are made to the input terminal block in
the J-box on top of the back box, eliminating the need
for wiring harnesses made in the field. Wire the control
cable according to the wiring diagram in Figure 1.
The back box is constructed of aluminum to meet most
fire code requirements for installation in open plenum
ceilings.
4.0 INSTALLATION
Save the shipping carton and plastic packaging in case
the unit must be returned for credit or repair.
4.1 CONDUCTOR AND CABLE
REQUIREMENTS
(All Models Except SB19)
A minimum of 12 conductors plus coax is required,
which includes common requirements for motorized
zoom lens and camera AC power. (An additional coax
is required for camera sync.)
2
Pelco Manual C467M-D (5/95)
Figure 1. SB1900 Series Wiring Diagram
Pelco Manual C467M-D (5/95)
3
4.3 MOUNTING INSTRUCTIONS
2. Remove the factory assembled 12.5" round face-
plate from the back box by disengaging the ser-
rated studs.
Determine the type of mounting desired. The enclo-
sure can be mounted in a hard ceiling, completely re-
place a standard 2' x 2' suspended ceiling tile using the
APSB19 optional faceplate, or be inserted through a
cut-out in a standard 2' x 2' suspended ceiling tile.
3. Remove the factory assembled 14.5" square mount-
ing plate by removing the four (4) 1/4-20 bolts.
4. Place the 14.5" square mounting plate on the re-
moved ceiling tile, centering all four edges of the
plate to the tile. Draw an outline of the octagon
opening in the sub-plate onto the tile.
Handle the lower dome with care so as not to scratch or
get fingerprints on the viewing window.
4.3.1 Suspended Ceiling Mounting
5. Using a sharp knife or keysaw, cut out the octagon
outlined on the tile.
4.3.1.1 Suspended Ceiling -
Preferred Method
6. Replace the ceiling tile and place the mounting
plate on top of it, centering the plate on the tile.
Attach the back box mount rails with 1/4-20 nuts
(provided) to two opposite sides of the mounting
plate. Use these mount rails to secure the back box
in place so that it can’t move when inserting or
removing the dome drive unit, and so that all of
the weight of the unit is not on the ceiling tile, per
local code. (Refer to Figure 2.)
1. Determine the location for mounting the enclosure
and remove the appropriate ceiling tile.
IMPORTANT: When installing the enclo-
sure in a 2' x 4' ceiling grid, cut the ceiling tile
in half and install an additional “T” rail for
support.
Figure 2. Back Box Mounting Rail Installation
4
Pelco Manual C467M-D (5/95)
7. Slide the back box through the ceiling tile and
mounting plate and replace the four (4) 1/4-20 bolts
and tighten to secure the back box to the mounting
plate.
NOTE: For PC1804B and PC900U cameras,
remove the mounting bracket with the two 1/4-
20 holes in it from the camera’s power supply,
align the camera power supply so that the two
(2) threaded holes in the power supply align
over two of the round holes in the camera power
supply bracket on the pan/tilt, and attach it with
the screws provided with the camera.
8. Check the alignment of the back box to the ceiling
tile by attaching the 12.5" round faceplate trim to
the bottom of the back box, aligning the two studs
with two of the holes in the flanges of the back
box and engaging the studs. The studs should en-
gage, while leaving a very minimal gap between
the ceiling and faceplate trim. Loosen the 1/4-20
hardware in the sides of the back box and make
adjustments as required. Insure that the face of the
back box is level with the ceiling.
11. Hook up camera power, video, and lens with the
connectors supplied, if not factory pre-assembled.
Coil the excess camera cable and tie it down with
tie-wraps to the pan/tilt body.
NOTE: To insert or remove the drive unit from
the back box, the drive unit may need to be ro-
tated 90° so that the wiring cover and/or cam-
era power supply does not interfere with the
side of the back box. If difficulty inserting or
removing the drive unit is experienced, slowly
and gently rotate the drive unit 90°.
9. Attach the lens and camera head to the tilt table
(hardware not supplied), if not factory pre-assembled,
using the camera/lens position template supplied
as a guide (see Figure 3). Locate the lens and cam-
era so that when the notched area in the template
is fitted under the tilt table, the lens and camera do
not project further out from the tilt table than al-
lowed by the template. Also, the lens must not
project higher than the long end of the template.
12. Engage the connector of the coil cord into the con-
nector of the pan/tilt and attach the safety clamp;
then insert the pan/tilt into the back box, feeding
the coil cord back through the opening in the top
of the back box. Position the pan/tilt in the back
box so that the horizontal studs in the pan/tilt mount
bracket align with the slots in the back box mount
bracket. Lift the pan/tilt until it reaches its stop,
then slide it to one side while letting it drop about
1/4 inch (see Figure 4).
NOTE: If the camera and lens do not fit within
the boundaries of the template, they will not fit
inside the dome and need to be replaced with
smaller units.
10. Mount the camera power supply onto the bracket
provided, if not factory pre-assembled. (Screws to
mount the camera power supply and lens are not
provided with the pan/tilt.)
LENS
SUPPLIED
TEMPLATE
CAMERA
3.25
(8.26)
MAX
TILT TABLE
.875
(2.22)
MAX
1.625
(4.13)
MAX
6.5
(16.51)
MAX
GENERAL LENS MAXIMUM EXTENSIONS
PAST EDGES OF TILT TABLE
NOTE: VALUES IN PARENTHESE ARE CENTIMETERS;
ALL OTHERS ARE IN INCHES
Figure 3. Camera/Lens Mounting Dimensions
Pelco Manual C467M-D (5/95)
5
13. Attach the dome to the pan/tilt by aligning the two
ball studs protruding through the flange of the dome
with the two holes in the dome attachment brack-
ets and engaging the studs.
15. Attach the faceplate trim to the back box by align-
ing the two serrated studs with two of the holes in
the edges of the back box and engaging the studs.
16. Operate the pan/tilt to verify that there are no ob-
structions or dragging cables within the back box
or dome.
14. Attach the safety chain on the side of the back box
to the short 4-40 threaded screw in the 12.5" round
faceplate trim with the provided hardware.
UPPER MOUNTING PLATE
INSIDE BACK COVER
SAFETY SPRING CLIP
ATTACHED TO COIL CORD
(CAN BE POSITIONED
180° FROM SHOWN)
LOWER MOUNTING PLATE
ATTACHED TO PAN AND TILT
Figure 4. Pan/Tilt Mounting Detail
6
Pelco Manual C467M-D (5/95)
4.3.1.2 Suspended Ceiling Tile
Replacement Mounting
template.Also, the lens must not project higher than
the long end of the template.
NOTE: If the camera and lens do not fit within
the boundaries of the template, they will not fit
inside the dome and need to be replaced with
smaller units.
To mount the enclosure into a suspended ceiling grid
where the tile is replaced, perform the following steps.
1. Determine the location for mounting the enclosure
and remove the appropriate ceiling tile.
8. Mount the camera power supply onto the bracket
provided, if not factory pre-assembled. (Screws to
mount the camera power supply and lens are not
provided with the pan/tilt.)
IMPORTANT: When installing the enclo-
sure in a 2' x 4' ceiling grid, cut the ceiling tile
in half and install an additional “T” rail for
support.
NOTE: For PC1804B and PC900U cameras,
remove the mounting bracket with the two 1/4-
20 threaded holes in it from the camera’s power
supply, align the camera power supply so that
the two (2) threaded holes in the power sup-
ply align over two of the round holes in the
camera power supply bracket on the pan/tilt,
and attach it with the screws provided with
the camera.
2. Angle the 23.75" back box mounting plate (part
number APSB19, which must be ordered sepa-
rately) through the grid opening and set the plate
into the grid. Attach the back box mount rails with
1/4-20 nuts (provided) to two opposite sides of the
mounting plate (see Figure 2). Use these mount
rails to secure the back box in place so that it can’t
move when inserting or removing the dome drive
unit, and so that all of the weight of the unit is not
on the ceiling tile, per local code.
9. Hook up camera power, video, and lens with the
connectors supplied, if not factory pre-assembled.
Coil the excess camera cable and tie it down with
tie-wraps to the pan/tilt body.
3. Remove the factory assembled 12.5" round face-
plate from the back box by disengaging the ser-
rated studs.
NOTE: To insert or remove the drive unit from
the back box, the drive unit may need to be ro-
tated 90° so that the wiring cover and/or cam-
era power supply does not interfere with the
side of the back box. If difficulty inserting or
removing the drive unit is experienced, slowly
and gently rotate the drive unit 90°.
4. Remove the factory assembled 14.5" square mount-
ing plate by removing the four (4) 1-4/20 bolts.
5. Slide the back box through the mounting plate and
replace the four (4) 1/4-20 bolts and tighten to se-
cure the back box to the mounting plate.
10. Engage the connector of the coil cord into the con-
nector of the pan/tilt and attach the safety clamp;
then insert the pan/tilt into the back box, feeding
the coil cord back through the opening in the top
of the back box. Position the pan/tilt in the back
box so that the horizontal studs in the pan/tilt mount
bracket align with slots in the back box mount
bracket. Lift the pan/tilt until it reaches its stop,
then slide it to one side while letting it drop about
1/4 inch (see Figure 4).
6. Check the alignment of the back box to the mount-
ing plate by attaching the 12.5" round faceplate
trim to the bottom of the back box, aligning the
two studs with two of the holes in the flanges of
the back box and engaging the studs. The studs
should engage, while leaving a very minimal gap
between the ceiling and faceplate trim. Loosen the
1/4-20 hardware in the sides of the back box and
make adjustments as required. Insure that the face
of the back box is level with the ceiling.
11. Attach the dome to the pan/tilt by aligning the two
ball studs protruding through the flange of the dome
with the two holes in the dome attachment brack-
ets and engaging the studs.
7. Attach the lens and camera head to the tilt table (hard-
ware not supplied), if not factory pre-assembled, us-
ing the camera/lens position template supplied as a
guide (see Figure 3). Locate the lens and camera so
that when the notched area in the template is fitted
under the tilt table, the lens and camera do not project
further out from the tilt table than allowed by the
Pelco Manual C467M-D (5/95)
7
12. Attach the safety chain on the side of the back box
to the short 4-40 threaded screw in the 12.5" round
faceplate trim with the provided hardware.
6. Attach the lens and camera head to the tilt table
(hardware not supplied), if not factory pre-assembled,
using the camera/lens position template supplied
as a guide (see Figure 3). Locate the lens and cam-
era so that when the notched area in the template
is fitted under the tilt table, the lens and camera do
not project further out from the tilt table than al-
lowed by the template. Also, the lens must not
project higher than the long end of the template.
13. Attach the faceplate trim to the back box by align-
ing the two serrated studs with two of the holes in
the edges of the back box and engaging the studs.
14. Operate the pan/tilt to verify that there are no ob-
structions or dragging cables within the back box
or dome.
NOTE: If the camera and lens do not fit within
the boundaries of the template, they will not fit
inside the dome and need to be replaced with
smaller units.
4.3.2 Hard Ceiling Mounting
To mount the enclosure into a hard ceiling, perform the
following steps.
7. Mount the camera power supply onto the bracket
provided, if not factory pre-assembled. (Screws to
mount the camera power supply and lens are not
provided with the pan/tilt.)
1. Determine the location and direction of the enclo-
sure. Ideally, the enclosure cutout should be paral-
lel and adjacent, or perpendicular, to any ceiling
structure. Cut an opening (refer to Figure 8 for di-
mensions).
8. Hook up camera power, video, and lens with the
connectors supplied, if not factory pre-assembled.
Coil the excess camera cable and tie it down with
tie-wraps to the pan/tilt body.
2. Remove the factory assembled 12.5" round face-
plate from the back box by disengaging the ser-
rated studs.
NOTE: To insert or remove the drive unit from
the back box, the drive unit may need to be ro-
tated 90° so that the wiring cover and/or cam-
era power supply does not interfere with the
side of the back box. If difficulty inserting or
removing the drive unit is experienced, slowly
and gently rotate the drive unit 90°.
3. Remove the factory assembled 14.5" square mount-
ing plate by removing the four (4) 1/4-20 bolts and
place it over the opening. Attach the back box
mount rails to the mounting plate with 1/4-20 nuts
(provided) to two opposite sides of the mounting
plate (see Figure 2). Use these mount rails to se-
cure the back box in place so that it can’t move
when inserting or removing the dome drive unit,
and so that all of the weight of the unit is not on
the ceiling tile, per local code.
9. Engage the connector of the coil cord into the con-
nector of the pan/tilt and attach the safety clamp;
then insert the pan/tilt into the back box, feeding
the coil cord back through the opening in the top
of the back box. Position the pan/tilt in the back
box so that the horizontal studs in the pan/tilt mount
bracket align with slots in the back box mounting
bracket. Lift the pan/tilt until it reaches its stop,
then slide it to one side while letting it drop about
1/4 inch (see Figure 4).
4. Slide the back box through the mounting plate and
replace the four (4) 1/4-20 bolts and tighten to se-
cure the back box to the mounting plate.
5. Check the alignment of the back box to the ceiling
by attaching the 12.5" round faceplate trim to the
bottom of the back box, aligning the two studs with
two of the holes in the flanges of the back box and
engaging the studs. The studs should engage, while
leaving a very minimal gap between the ceiling
and faceplate trim. Loosen the 1/4-20 hardware in
the sides of the back box and make adjustments
are required. Insure that the face of the back box is
level with the ceiling.
10. Attach the dome to the pan/tilt by aligning the two
ball studs protruding through the flange of the dome
with the two holes in the dome attachment brack-
ets and engaging the studs.
11. Attach the safety chain on the side of the back box
to the short 4-40 threaded screw in the 12.5" round
faceplate trim with the provided hardware.
8
Pelco Manual C467M-D (5/95)
12. Attach the faceplate trim to the back box by align-
ing the two serrated studs with two of the holes in
the edges of the back box and engaging the studs.
2. Pan to the desired left position, remove the drive
unit from the back box and adjust the pan limit
stop until the actuator clicks, and lock into posi-
tion. Replace the drive unit.
13. Operate the pan/tilt to verify that there are no ob-
structions or dragging cables within the back box
or dome.
3. Pan to the right and left to verify the exact posi-
tioning.
4.4 CONNECTOR ASSEMBLY
4. The tilt limit is factory set at 0 to -90° travel (hori-
zontal to vertical). The tilt can be adjusted to any
point between horizontal and vertical; however,
under normal conditions the tilt limits should not
require adjustment.
To install and test the SB1900 Series enclosures you
may need to fabricate the interconnecting cable as out-
lined below. (Pretested wire harnesses, WH1900-06 and
WH1900-25, are optional cables for the SB1900 Se-
ries dome enclosures).
5. To alter the factory set tilt limit*, bend the actua-
tor stops on the microswitches (see Figure 6).
Move the tilt table to the desired position and ad-
just the actuators until the switch clicks; lock into
position.
1. Strip back the cable jacket approximately 2 inches
and separate the individual conductors.
2. Attach spade lugs to each wire and mate BNC to
coax and camera sync.
6. Tilt up and down to verify exact positioning.
3. Pop out a knock-out in one of the ends of the J-box
(on top of back box). Thread cable into J-box
through knock-out and attach each wire to the ter-
minal block, as marked beside terminal block, and
engage BNC connectors or video and camer sync.
* It should be emphasized that only very minor adjust-
ments should be made by bending the actuator attached
to the microswitch; and then, only for the reason of
bringing it within factory specifications.
4.5 ADJUSTMENTS
To adjust the pan/tilt limits, perform the following steps.
Refer to Figure 5 for limit stop locations.
LIMIT STOP LEFT
LIMIT STOP RIGHT
LIMIT STOP FIXED
LIMIT ACTUATOR
CAUTION: Do not attempt to adjust limit
stops when the pan/tilt is in operation. Damage
to the equipment can result. Also, do not oper-
ate equipment without limit stops. Note that SL
models are supplied without pan limit stops,
therefore, no adjustments are necessary.
Factory pan limits are set to 0-355° and tilt limits are to
0-90° (horizontal to vertical). Under normal conditions,
the tilt limits should not have to be reset.
To adjust limit stops, perform the following steps:
1. Pan to the right using the joystick control until the
desired pan limit is reached. Remove the drive unit
from the back box and adjust the pan limit stop
until the actuator clicks. Lock the limit into posi-
tion. Replace the drive unit.
NOTE: FIGURE IS A REPRESENTATION OF AN ACTUAL UNIT
WITH SOME PARTS NOT SHOWN TO PROVIDE
CLARITY OF LIMIT STOP LOCATIONS
Figure 5. Limit Stop Locations
Pelco Manual C467M-D (5/95)
9
5.0 CARE AND MAINTENANCE
If dust or other debris accumulates on the inside of the
lower dome, remove with clean air pressure only. Com-
pressed air cans are available from commercial photo-
graphic equipment and supply dealers.
Regularly scheduled maintenance will prolong the op-
erational life and appearance of the equipment.
IMPORTANT: The lower dome of the en-
closure is an optical surface. When cleaning the
inner surface of the dome and viewing window,
treat as carefully as you would a fine camera
lens. Do not use water, liquid or spray cleaners
of any kind on coated inner surface of dome.
Clean the outer surface of the dome and the inner sur-
face of the viewing window with a non-abrasive clean-
ing cloth and anti-static cleaner that is safe for use on
acrylic plastic. Do not use kerosene or similar sub-
stances that can scratch the surface.
LIMIT ACTUATOR
UP
DOWN
LOCKING SCREW
UP
FRONT
DOWN
Figure 6. Tilt Limit Stop Modification
10
Pelco Manual C467M-D (5/95)
6.0 EXPLODED ASSEMBLY DIAGRAM
Refer to Figure 7 for an exploded assembly diagram of the SB19 enclosure.
PP ONLY
NON SL ONLY
*
**
EXPASB1900
EXPASB1900PP
Figure 7. SB19 Exploded Assembly Diagram
Pelco Manual C467M-D (5/95)
11
7.0 EXPLODED ASSEMBLY MECHANICAL PARTS LIST
Item
Qty
Description
Pelco Part Number
1
2
3
4
5
6
1
1
1
1
1
2
UL, Pad, camera, black .062" thick
PCB assembly, pan/tilt
Bushing, 3/8" tilt shaft
Shaft, tilt table
Sprocket .25" bore with pin and SS
Ball stud receiver
EH200010004
PCB3000100ASSY
PT180010001
PT18004002COMP
PT18004003COMP
PT180410001
7
Not used
8
9
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
4
2
2
6
2
1
1
1
1
2
1
1
2
1
Tilt Chain assembly
Pan Chain assembly
Tilt shaft, motor side
PT18041006ASSY
PT18041007ASSY
PT18041011WA
PT18041012WA
PT18044002COMP
PT18044055COMP
PT18044006COMP
PT18044009COMP
PT1804410COMP
PT18044011COMP
PT18044014COMP
PT250010004
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Frame body, weld assembly
Dome attachment bracket
Spindle, pan
Mount, lower pan and tilt
Bracket, PC1804-B power supply
Pan motor heat sink mount
Pan motor heat sink
Connector spacer, spindle mount
Bushing
Bushing, 1/4", tilt shaft
Sprocket, pan spindle
Tilt table
PT250010005
PT25004104COMP
PT25004106COMP
PT25004108COMP
PT25004121COMP
PT25004125COMP
PT350010000
Tilt limit actuator
Collar, tilt table switch shaft
Spricket, 1/4" with SS and pilot
Bearing, flange
UL, motor, 4 rpm, 24VAC
Plate, bearing
Collar, tilt table motor side
NP spacer, 1/4" OD x .125, #6 clear
Switch
Switch actuator with insulator
NP cable, S/S x inch
Connector ring, 14-wire #4 stud
Coil cord
Black box assembly, 10.9" octagon
Trim ring assembly
Mount, upper pan/tilt
J-box end
J-box cover
PT350010010
PT35001060COMP
PT89104001COMP
SPA8500
SWI1SM1
SWIJS138B
E70810001
E70810002
PT180410002
SB10841010ASSY
SB18044100COMP
SB18044105COMP
SB18044105COMP
SB18044006COMP
SSB18044007COMP
SB18044009COMP
SB184220COMP
Boack box mount plate
BNC panel mount bracket
8" dome camera/lens position template
Not used
4
2
1
Back box mount rail
SB194002COMP
TRB-2MV-10
SB194200COMP
Terminal block, 10-position PC mount
Black opaque dome with smoked viewing window
and mounting studs
1
Black opaque dome with clear viewing window
and mounting studs
SB194300COMP
12
Pelco Manual C467M-D (5/95)
7.0 EXPLODED ASSEMBLY MECHANICAL PARTS LIST (continued)
Item
Qty
Description
Pelco Part Number
48
49
Not used
Not used
50
Not used
51
52
1
Slip ring, 24 circuit for presets
Not used
250010000
53
Not used
54
Not used
55
56
57
58
59
60
61
1
1
1
2
2
1
1
Bracket, tilt pot
Bracket, LPP lens connector
Gear, 1.875 plastic
Gear, 1.5 plastic
Pot, precision 10K
Gear, spindle feedback, non-SL
Pan feedback pot
Not used
PT18044012COMP
PT18044013COMP
PT250010002
PT250010006
POTP010.0K
PT25004114COMP
PT25004116COMP
62 thru 70
71
2
1
3
Ring snap
15510000
2704051COMP
5804006COMP
72
73
74
Bracket, pan limit
Limit stop, pan univ
Not used
75
76
1
Grommet, neoprene
Not used
GRO2172N
77
Not used
78
79
80
1
1
1
Pan limit stop ring
Bracket, pan limit mount
Pan limit actuator pin
PT18044018COMP
PT18044019COMP
PT18044020COMP
Pelco Manual C467M-D (5/95)
13
8.0 MODELS
DD1900
SB1900-PP
SB1901-PP
Same as the SB1900, except this
package features the factory installed
preset (PP) option.
Dome drive unit for SB1900. (UL)
Dome drive unit for SB1900-PP.
DD1900-PP
DD1900-SL
Same as SB1900-PP except supplied
with clear viewing slot in the dome
for virtually zero light loss.
Dome drive unit for SB1900-SL.
(UL)
SB1900SL-PP Same as the SB1900-SL with the
addition of the preset (PP) option.
DD1900SL-PP Dome drive unit for SB1900SL-PP.
SB19
Drop ceiling discreet surveillance
enclosure with black opaque lower
dome with less than 1 f-stop light at-
tenuation and all aluminum back box
which mounts above the ceiling.
(Camera mount supplied.) (UL)
SB1901SL-PP Same as SB1900SL-PP except sup-
plied with clear viewing slot in the
dome for virtually zero light loss.
9.0 RECOMMENDED CONTROLS
The following controls are recommended for use with
the SB1900 Series enclosures.
SB19-1
SB1900
Same as SB19 except supplied with
clear viewing slot in the dome for
virtually zero light loss. (UL)
9.1 MODELS SB1900 AND SB1900-SL
This system package includes the
SB19 black opaque dome enclosure
plus a 24 VAC pan/tilt factory as-
sembled inside the back box. It pro-
vides factory pre-wired feedthrough
for all control functions (i.e., pan/tilt,
motorized zoom lens, camera power
(24 VAC) and video).All connections
are made at the terminal blocks on
top of the back box, eliminating wir-
ing harnesses made in the field. This
feature significantly reduces installa-
tion time while increasing the reliabil-
ity and serviceability of the system.
(UL)
Hardwire Short-Distance Controls
for 24 VAC Operation
MPT24DT
MPTA24DT
MLZ6DT
Desk top joystick control module for
24 VAC pan/tilts.
Same as MPT24DT except with auto/
random scan operation.
Desk top zoom lens control module
with auto/manual iris control.
Desk top enclosure control module
for 24 VAC camera on/off.
MEH24DT
Coaxitron System 2000
MPT9000CZ
Desk top Coaxitron transmitter/control
with pan/tilt joystick, zoom lens, and
four accessory function controls.
SB1901
Same as SB1900 except supplied
with clear viewing slot in the dome
for virtually zero light loss. (UL)
CX9024RXI
Desk top Coaxitron receiver for 24
VAC pan/tilts, zoom lens, 24 VAC
camera power and optional four ac-
cessory functions. Indoor use.
SB1900-SL
SB1901-SL
Same as the SB1900, except this
package features 360° continuous
pan rotation. (UL)
A9000
Auto/random scan plug-in module
for all Coaxitron receivers.
Same as SB1900-SL except supplied
with clear viewing slot in the dome
for virtually zero light loss. (UL)
CX900TLC
System test and receiver manual con-
trol board for Coaxitron receivers
(plug-in module).
14
Pelco Manual C467M-D (5/95)
9.2 MODELS SB1900, SB1900-SL,
SB1900-PP AND SB1900SL-PP
IOP19B1C
B/W NTSC 6X camera and lens pkg.
with preset positioning.
CM7500 Series Coaxitron Matrix Switcher/Control
System rack mount card cage with
CPU and power supply. Capable of
up to 64 inputs and up to 4 monitor
outputs. (See C584 product specifi-
cation sheet for details).
IOP19B1G
IOP19C1B
IOP19C1C
B/W NTSC 10X camera/lens pkg.
Color NTSC 6X camera and lens pkg.
Color NTSC 6X camera and lens
pkg. with preset positioning.
CM8500 Series Matrix Switcher/Control System ca-
pable of up to 32 inputs and 16
monitor outputs. (See C501 product
specification sheet for details).
IOP19C1G
Color NTSC 10X camera and lens pkg.
WH1900-06
6 foot wire harness with bare wire on
one end (for connection to the termi-
nal blocks in the junction box on top
of the back box) and a 37 position con-
nector on the other end (for connec-
tion to Coaxitron receiver).
CM9500 Series Coaxitron Matrix Switcher/Control
System rack mount card cage with
CPU and power supply. Capable of
up to 96 inputs and 16 monitor out-
puts. (See C500 product specification
sheet for details).
WH1900-25
Same as WH1900-06, except 25 feet
long.
CX9024RXI-PP Coaxitron indoor receiver for 24 VAC
pan/tilts, zoom lens, 24 VAC camera
power and optional four accessory
functions, with preset option (PP) for
pan/tilt and lenses (use with models
SB1900-PP and SB1900SL-PP).
(Must be used with CM7500/CM9500
series controls only.)
11.0 SPECIFICATIONS
MECHANICAL
Construction:
Pan/tilt
Back box
Aluminum
Aluminum
Lower dome Acrylic hemisphere with a clear,
distortion-free viewing window
with no light attenuation factor
(SB1901 Series) or smoked, distortion-
free viewing window with less than
1 f-stop light attenuation (SB1900 Se-
ries); rotates with the pan/tilt/camera/
lens
CX900TLC
System test and receiver manual con-
trol board for Coaxitron receivers
(plug-in module).
MPT9500
Desktop controller (coaxitron com-
patible) with full PTZ, joy stick, 8
auxiliary functions.
Maximum
Camera/Lens
Size:
10.0 OPTIONS
6.5" L x 4.5" W x 3.25" H, including
BNC (16.51 cm x 11.43 cm x 8.25 cm);
maximum camera head width is
2.50" (6.35 cm) (see Figure 3)
RB24
Relay box for 24 VAC pan/tilts and
scanners. Extends operating distance
(control to relay box) up to a maxi-
mum of 14,500 feet utilizing 16Awg.
Max. Camera
Power Supply
Size:
APSB19
23.75" square faceplate for suspended
ceiling applications.
2.5" x 5.0" x 2.5"
(6.35 cm x 12.7 cm x 6.35 cm)
APSB19-1
IOP19B1B
Same asAPSB19 except black finish.
B/W NTSC 6X camera and lens pkg.
Pan:
0-355° movement in horizontal
plane (Models SB1900, SB1900-PP)
360° continuous rotation (Models
SB1900-SL, SB1900SL-PP)
Pelco Manual C467M-D (5/95)
15
Pan Speed:
Tilt:
24°/sec ± 1°
Lens Connector: Hirchmann 6100 type (mate supplied)
for non-PP models
-90° movement from horizontal plane
12°/sec ± .5°
AMP CPC type (mate supplied) for
PP models
Tilt Speed:
Motors:
Synchronous type, continuous duty,
instantaneous reversing
Maximum Load: 10 lbs (4.6 kg)
Gearing:
Chain drive
Limit Switches:
Pan
5 amp, 10 million cycle rating (ex-
ternal adjustment) on non-SL
5 amp, 10 million cycle rating (factory
set)
Bearings:
Pan
Heavy duty ball bearing and Oilite
bronze bushing
Tilt
Tilt
Oilite bronze bushing
Conductor
Requirements:
Non-PP
Braking:
Friction
ELECTRICAL
Input Voltage:
models
Pan/tilt (5 plus ground), Lens (4),
Camera AC (2), Video (coax), Cam-
era Sync (coax)
24 VAC required for pan/tilt
Power
Requirements:
Pan
PP models
Pan/tilt (9 plus ground), Lens (6),
Camera AC (2), Video (coax), Cam-
era Sync (coax)
.31 amp (7.5 vA)
.31 amp (7.5 vA)
Tilt
GENERAL
Connectors:
Terminal strips inside J-box on the top of
the back box (all functions except video:
camerapower, lens, pan/tiltandpresets).
Environment:
Indoor
Temperature
Range:
Video
14°F to 122°F (-10°C to +50°C)
Connector:
BNC
Dimensions:
See Figure 8
Camera Power: Spade lugs, 24 VAC
9.25
(23.50)
1.65
(4.19)
1.80
(4.58)
A
7.93
(20.14)
3.10
(7.87)
11.00
(27.94)
B
C
C
B
A
WHERE:
8.50
(21.59)
A
B
C
10.90 (27.69)
7.70 (19.56)
12.50
(31.75)
3.20
(8.13)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.
Figure 8. SB19 Dimension Drawing
16
Pelco Manual C467M-D (5/95)
12.0 WARRANTY AND RETURN
INFORMATION
WARRANTY
RETURNS
Pelco will repair or replace, without charge, any merchandise proved
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate
of shipment.
In order to expedite parts returned to the factory for repair or credit, please
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).
Exceptions to this warranty are as noted below:
All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and
keyboard).
Three years on Camclosure® and fixed camera models, except the
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.
Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.
•
If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and
DF5/DF8 Series fixed dome products.
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, includ-
ing when used in continuous motion applications.
Two years on Esprit® and WW5700 Series window wiper (excluding
wiper blades).
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
•
•
•
If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
Eighteen months on DX Series digital video recorders, NVR300
Series network video recorders, and Endura™ Series distributed
network-based video products.
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
•
•
One year (except video heads) on video cassette recorders (VCRs).
Video heads will be covered for a period of six months.
If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:
Six months on all pan and tilts, scanners or preset lenses used in
continuousmotionapplications(thatis,presetscan,tourandautoscan
modes).
Pelco c/o Expeditors
473 Eccles Avenue
Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800)
289-9100 or (559) 292-1981 to obtain a Repair Authorization number
(RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice
number
3. Details of the defect or problem If there is a dispute regarding the
warranty of a product which does not fall under the warranty conditions
stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
Pelco Manual C467M-D (5/95)
17
Pelco
3500 Pelco Way • Clovis, CA 93612-5699
(559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827
International customers call 1-559-292-1981 or FAX 1-559-348-1120
(Product specifications subject to change without notice.)
18
Pelco Manual C467M-D (5/95)
|