®
C1906, C1925, C19125,
C1906/PP and C1925/PP
Pre-wired Interconnecting
Inverting Cables
Installation/Operation Manual
C930M-E (12/95)
Amended 1/96
PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827
INSTALLATION AND OPERATION MANUAL
MODELS C1906, C1925, C19125, C1906/PP,
AND C1925/PP
PRE-WIRED INTERCONNECTING
INVERTING CABLES
1.0 WARNINGS
3.0 DESCRIPTION
1. Installation and Servicing should only be done
by Qualified Service Personnel.
The C1906, C1906/PP, C1925, C1925/PP and C19125
are pre-wired cables designed for interconnecting
Pelco’s Coaxitron® receiver/driver with various Pelco
domes or any inverted PT180-24P/PT280-24P pan/tilt
application as listed below.
2. The installation shall be done in accordance
with all local and national electrical and me-
chanical codes utilizing only approved mate-
rials.
C1906, C1925, C19125
Domes:
ED2820, ED2820-3, ED2820-SL,
ED2920, ED2920-SL,
3. Unless the cable is specifically marked “WA”
(for use in wet locations), the cable is designed
for indoor use only and it must not be installed
where exposed to rain and moisture.
SB2800, SB2800-2, SB2800-SL,
SB2800-SL-2, SB2801
SS3000, SS3002
2.0 SCOPE
Pan/Tilts:
PT180-24P, PT180-24SL,
PT280-24P, PT280-24SL
The information within this manual covers the installa-
tion and operation of the C1906, C1925, C19125,
C1906/PP, and C1925/PP pre-wired interconnecting
inverting cables.
C1906/PP, C1925/PP
Domes:
ED2820-PP, ED2820SL/PP,
ED2820-3SL/PP, SB2800/PP,
SB2800-SL/PP
Please thoroughly familiarize yourself with the infor-
mation in this manual prior to installation and opera-
tion.
Pan/Tilts:
PT180-24P/PP,
PT280-24P/PP, PT280-24SL/PP
3.1 MODEL NUMBERS
C1906
6 ft (1.83 m), pre-wired intercon-
necting inverting cable. (UL)
C1925
25 ft (7.62 m), pre-wired intercon-
necting inverting cable. (UL)
C19125
C1906/PP
C1925/PP
125 ft (38.1 m), pre-wired inter-
connecting inverting cable. (UL)
6 ft (1.83 m), same as C1906 but
for PP models. (UL)
25 ft (7.62 m), same as C1925 but
for PP models. (UL)
Pelco Manual C930M-E (12/95)
1
4.0 SPECIFICATIONS
ELECTRICAL
6.0 OPERATION
By using the controller, you should be able to control
the pan and tilt functions of the pan/tilt and the focus,
iris, and zoom functions of the motor operated lens.
Connectors:
Receiver side
Pan/tilt side
CPC, 37 sockets
CPC, 14 pins
CPC, 28 pins (PP models)
6.1 SYSTEM TEST
Using the controller, operate the following functions
and verify correct operation of each function:
Cable:
12 conductor with shield, 20 Awg
RG59/U
1. Pan Left
GENERAL
2. Pan Right
3. Tilt Up
Cable length:
C1906
C1925
C19125
C1906/PP
C1925/PP
4. Tilt Down
5. Zoom Wide
6. Zoom Telephoto
7. Iris Open
8. Iris Closed
9. Focus Near
10. Focus Far
6 ft (1.83 m) long
25 ft (7.62 m) long
125 ft (38.1 m) long
6 ft (1.83 m) long
25 ft (7.62 m) long
Maximum Wire
Temperature:
140° F (60° C)
If all the above functions operate correctly, the instal-
lation process is complete. If all the above functions do
not operate correctly, refer to Section 7.0, Troubleshoot-
ing Guidelines.
5.0 INSTALLATION
1. Run the cable from the Coaxitron® receiver/driver
to the pan/tilt. Be careful not to abrade or cut the
jacket on the cable since this could result in a short.
For PP models — check all of the above again
using a set preset location.
2. Connect the 37-pin CPC connector to the
Coaxitron® receiver/driver.
3. Connect the 14-socket CPC connector (28-pin PP
models) to the pan/tilt unit.
4. Operate the control unit and determine correct op-
eration of the unit. If the unit fails to operate cor-
rectly, refer to the troubleshooting guidelines out-
lined in Section 7.0.
2
Pelco Manual C930M-E (12/95)
7.0 TROUBLESHOOTING GUIDELINES
NOTE: These cables are designed for use
in inverted applications. If you wish to modify
the cable for upright operation, pins 3 and 7
(pan) and pins 5 and 6 (tilt) need to be re-
versed on the 14- or 28-pin connector (pan/
tilt side). The problem can be corrected in the
field with a CPC pin/socket extracting tool
by simply exchanging the pins for these func-
tions. If you do not have the necessary tool,
contact Pelco for a R/A number to exchange
the cable.
1. If none of the functions in Section 6.1 operate cor-
rectly, check the connection of the CPC connec-
tors to the Coaxitron® receiver/driver and pan/tilt.
2. If the connections are loose, tighten the lock ring
on the CPC connectors and start the system test
procedure in Section 6.1.
3. If the connections are tight, check the Coaxitron®
receiver/driver to determine if it is operating cor-
rectly. If the Coaxitron® receiver/driver is operat-
ing correctly, there may be a problem with the cable
and Pelco’s Technical Assistance Program (TAP)
should be contacted for further technical trouble-
shooting aid. To contact the TAPline, call 1-800-
289-9100.
8.0 SCHEMATICS
Refer to Figures 1-3 for wiring diagrams of the pre-
wired cables.
Figure 1. C1906, C1925, and C19125 Wiring Diagram
Pelco Manual C930M-E (12/95)
3
Figure 2. C1906/PP and C1925/PP Wiring Diagram
4
Pelco Manual C930M-E (12/95)
Figure 3. C1906/PP and C1925/PP Wiring Diagram for Use with Upright Pan/Tilts Only
Pelco Manual C930M-E (12/95)
5
9.0 WARRANTY AND RETURN
INFORMATION
WARRANTY
RETURNS
Pelco will repair or replace, without charge, any merchandise proved
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate
of shipment.
In order to expedite parts returned to the factory for repair or credit, please
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).
Exceptions to this warranty are as noted below:
All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and
keyboard).
Three years on Camclosure® and fixed camera models, except the
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.
•
If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and
DF5/DF8 Series fixed dome products.
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, includ-
ing when used in continuous motion applications.
Two years on Esprit® and WW5700 Series window wiper (excluding
wiper blades).
•
•
•
Eighteen months on DX Series digital video recorders, NVR300
Series network video recorders, and Endura™ Series distributed
network-based video products.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
•
•
One year (except video heads) on video cassette recorders (VCRs).
Video heads will be covered for a period of six months.
If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:
Six months on all pan and tilts, scanners or preset lenses used in
continuousmotionapplications(thatis,presetscan,tourandautoscan
modes).
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.
Ifawarrantyrepairisrequired,theDealermustcontactPelcoat(800) 289-
9100 or (559) 292-1981 to obtain a Repair Authorization number (RA),
and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice
number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written
explanation with the product when returned.
®
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.
Pelco
300 West Pontiac Way, Clovis, CA 93612-5699
(559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827
(Product specifications subject to change
without notice.)
Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
C930M-D
Endura and ExSite are trademarks of Pelco.
© Copyright 1995, Pelco. All rights reserved.
6
Pelco Manual C930M-E (12/95)
|