In-Ceiling Speaker
CM590i
Technical Information for System Engineers
Key Features
• High power output (109 dB) for longer
throw and higher SPL requirements.
• One 133 mm (5.25 in) polypropylene
woofer and one 25 mm (1.0 in) horn-
loaded convex aluminum dome tweeter
mounted to a proprietary cast-alumi-
num HP5TM baffle & heat sink.
• 90 dB Average sensitivity offers high
output capabilities and reduced amplifi-
cation costs.
Tile bridge included
Specifications: CM590i
System Type
5.25” Coax, in-ceiling, ported (33 Watt transformer
• Rapid installation blind-mount, fixed-
wing mechanism with constant tension
design affixing to ceiling thickness tol-
erances rangeing from 6.4 mm (0.25 in)
to 42.9 mm (1.69 in).
for 25/70.7/100 Volt or voice coil/8 Ohm direct)
77 Hz - 22 kHz
69 Hz - 20 kHz
160 Watts
80 Watts
55 Watts
109 dB
90 dB
Frequency Response (- 3 dB)1
Low Frequnecy (-10 dB)1
Max. Program Power
Max. Continuous Power RMS
Max. UL Power Rating3
Max. SPL dB @ 1 M
• Magnetic grille attachment with
safety cable.
Sensitivity dB @ 1W/1M4
• Easy access 6-position selectable tap
switch for 25, 70.7 & 100 Volt applica-
tions with voice coil/8 Ohm direct sim-
plifies ordering and inventory tracking.
Impedance (nominal)
8 Ohm (nominal value)
180º (average)
102º (average)
7.7 (Averaged 100 Hz - 10 kHz); 11.17 @ 2 kHz
8.04 dB (Averaged 100 Hz - 10 kHz); 10.48 dB @ 2 kHz
6-Position rotary switch with voice coil/8 Ohm direct
Coverage Angle (-6 dB @ 500 Hz)
Coverage Angle (-6 dB @ 4 kHz)
Directivity Factor (Q)
Directivity Index (DI)
Tap Selector
• UL 1480 rev. 5 & 2403, CE (EMC Directive
89/366/EEC, EN55020, EN55013), Milspec
810 or IEC529 approval pending.
Transformer Taps
70.7 V Output
33 W 105 dB
17 W 102.5 dB
9 W 99.5 dB
6 W 98 dB
100 V Output
33 W 105 dB
17 W 102.5 dB
9 W 99.5 dB
6 W 98 dB
25 V Output
• Included accessories: Tile bridge, Euro-
block connector, installation aid, paint
mask and conduit plate.
5 W 97 dB
2.5 W 94 dB
1.3 W 91 dB
0.63 W 88 dB
• Optional accessories: Pre-Construction
Bracket and Junction Box.
3 W 95 dB
• High quality black or white paint finish.
Custom paint colors optional.
Transducers
Low Frequency Driver
High Frequency Driver
Low Frequency Voice Coil
Crossover Frequency
1 x 133 mm (5.25 in) Polypropylene cone, butyl rubber surround
25 mm (1.0 in) Convex aluminum horn-loaded tweeter
25 mm (1.0 in)
3 kHz
Description
The CM590i is a high-powered 5.25”
2-way loudspeaker in a ported in-ceiling
enclosure design. The CM590i incorporates
a low-profile grille, proprietary HP5TM
motor-board and 6-position tap switch
with voice coil/8 Ohm direct. A tile bridge
is included and the speaker features a fast-
action SpeedWingTM for easy and secure
installation.
Network Type
Low Pass
High Pass
Enclosure Material
Motor Board
Grille
N/A
12 dB per octave, 2nd order
Drawn aluminum backcan with ABS baffle
Cast aluminum
Iridite-plated steel with powder-coat finish
4 Pin, 5 mm Euroblock for individual or daisy chain connection
Black or white
197 mm / 7.75 in
219.2 mm / 8.63 in
271.9 mm / 10.71 in
24.5 mm / .96 in
Inputs
Colors
Backcan Diameter
Backcan Height
Visible Diameter
Visible Height
Weight
Applications
Engineered for high-SPL and effective
low-end response (69 Hz @ - 10 dB), the
CM590i delivers consistent high-perfor-
mance music and paging for applications
requiring longer throw or higher volume
above the existing ambient noise level. The
CM590i is ideal for in-ceiling sound rein-
forcement/PA in applications with high
ambient noise levels including casinos,
warehouses, airports, transportation & ship-
ping centers, schools, gyms, arenas and sta-
diums. For additional bass down to 43 Hz
(-10 dB) the CM801i subwoofer may be used.
3.4 kG / 7.5 lbs
10.7 kG / 23.5 lbs (2 per box, includes tile bridges)
Shipping Weight
Accessories
Included
Tile bridge, Euroblock connector, installation aid, paint mask
& conduit plate
Pre-Construction Bracket (AC-CM5-PCB),
Junction Box (AC-CM-JBOX)
Optional
Packaging
2 Per box, can ship as single
1
2
3
4
Frequency response is measured in half space and includes a low-frequency peak > + 3 dB.
Continuous power rating, EIA-426-B test.
UL testing specifies band-limited pink noise over the indicated frequency spectrum.
2.83 Volts at a distance of 1 meter.
SoundTube continually develops new product innovations and improvements. Updates to existing
products without prior notice are an example of SoundTube’s drive for constant improvement.
© 2006 SoundTube Entertainment. All rights reserved. PN TS-CM590 REV 03.03.06
In-Ceiling Speaker
CM590i
Preliminary Technical Information for System Engineers
Data Acquisition
constructed of glass-filled ABS material.
The external wiring input connector shall
be a 4-pin, 5 mm Euroblock for 8 Ohm or
distributed systems and shall accept from
10 – 22 gauge wire.
Useable frequency response shall
extend from 69 Hz – 22 kHz (-10 dB,
All performance data acquired at
SoundTube’s Technical Measurement
Center (TMC) are analyzed using a
variety of standard measurement tech-
niques, including Measured Length
Sequence (MLS) and Time Delay Spec-
trometry (TDS). Performance, develop-
ment and data acquisition tools include:
Gold Line TEF 20, CLIO, LMS, LEAP, and
proprietary modeling software. EASE™
data are acquired through an automated
TEF 20/Outline/EASE™ interface.
half space, no external equalization).
Measured sensitivity (2.83 Volt input,
1 meter) shall be at least 90 dB. The
speaker shall have a nominal imped-
ance of 8 Ohms and shall be available
for 25/70.7/100 Volt modes with voice
coil/8 Ohm direct. The frequency-
dividing network shall have a cross-
over frequency of 3 kHz with a slope
of 12 dB per octave (second order)
for the high-pass filter. Rated power
capacity shall be at least 80 Watts con-
tinuous power (RMS), and conforms to
EIA-426-B testing. Maximum continu-
ous output at 1 meter shall be 109 dB.
The maximum backcan dimensions
shall be no more than 197 mm (7.75 in) in
height by 219.2 mm ( 8.63 in) in diameter.
The maximum visible dimensions shall be
no more than 24.5 mm (0.96 in) in height
by 271.9 mm (10.71 in) in diameter. The
backcan shall be construction of alumi-
num and affixed to an ABS baffle.
EASE™ Data – 3-D polar plots.
The system shall include a 16-guage
galvanized steel support backing plate
(tile bridge) to reinforce the ceiling mate-
rial and tile support rails. The maximum
tile bridge dimensions shall be no more
than 600.1 mm (23.61 in) in length by 323.9
mm (12.75 in) in width and 11 mm (0.41 in)
in thickness with a 228.6 mm (9.0 in) diam-
eter cutout for speaker mounting.
SoundTubeSPEC™ – Proprietary
SoundTube speaker placement software.
The low-frequency transducer shall
have a polypropylene cone with butyl rub-
ber surround. The high-frequency trans-
ducer shall be constructed of aluminum
material and incorporate a high-SPL horn.
Architectural Specifications
The loudspeaker shall consist of a
133 mm (5.25 in) low-frequency trans-
ducer and a 25 mm (1 in) high-frequency
transducer with a frequency-dividing
network installed in a ported enclosure.
The low-frequency voice coil diameter
shall be 25 mm (1 in).
Installation for the CM590i shall be by
2-screw, blind-mount, constant-tension
winged assembly and shall attach to
ceiling thickness tolerances ranging
from 6.4 mm (0.25 in) to 42.9 mm (1.69
in). The fixed-wing assembly shall be
The grille shall be constructed of an ABS
bezel and iridite-plated, powder-coated
steel for lasting performance. The affixed
grille and bezel shall be mounted to the
speaker enclosure (backcan) via neo-
Performance specifications of a typi-
cal production unit shall be as follows:
Polar Plots
250 Hz
500 Hz
1,000 Hz
125 Hz
4,000 Hz
8,000 Hz
10,000 Hz
2,000 Hz
™
™
Technical data, EASE plots, SoundTubeSPEC software & product downloads available at www.soundtube.com
In-Ceiling Speaker
CM590i
Preliminary Technical Information for System Engineers
Mechanical Drawings
dymium magnets and include a safety
strap. Also included are a paint mask
for in-field painting and an installation
aid that serves as a hand-hold for instal-
lation.
Side
Top
The CM590i has an optional Pre-Con-
struction Bracket (AC-CM5-PCB) that
shall be compatible with an optional
Junction Box (AC-CM-JBOX). An 18-
gauge wire whip and Euroblock connec-
tor shall be included with the Junction
Box. The maximum dimensions of the
Pre-Construction Bracket with Junc-
tion Box shall be no more than 635
mm (25 in) in length by 381 mm (15.0
in) in width and 128 mm (5.0 in) thick-
ness with a 228.6 mm (9.0 in) cutout for
speaker mounting.
197 mm
(7.75 in)
219.2
mm
(8.63 in)
271.9 mm (10.71 in)
24.5 mm
(0.96 in)
Included Accessories
The system shall be the SoundTube
CM590i with mounting hardware for both
low and high impedance applications.
SoundTube Entertainment
6430 North Business Park Loop
Park City, Utah 84098
Phone 435.647.9555
600.1 mm
(23.62 in)
228.6 mm
(9.00 in)
Fax
435.647.9666
Toll Free 800.647.TUBE
Max.
Min.
42.9 mm (1.69 in)
6.4 mm (0.25 in)
All SoundTube products come
with a 5-year limited warranty.
Fixed Wing Mounting System
323.5 mm (12.75 in)
Tile Bridge
Paint Mask
Optional Accesories
Pre-Construction Bracket (AC-CM5-PCB)
Junction Box (AC-CM-JBOX)
SoundTube Entertainment manufactures a complete line of speakers for:
Open-Ceiling • In-Ceiling • Surface-Mount • Outdoor • Sound-Focusing
All SoundTube products are designed and engineered in the USA.
|