Audio CD Recorder
CDR950/951
Instructions for use
Mode d'emploi
•
•
•
•
•
•
•
•
••
•
•
•
Instrucciones de manejo
Bedienungsanleitung
Gebruiksaanwijzing
Istruzioni per l'uso
Brugsanvisning
Bruksanvisning
Käyttöohje
Manual de utilização
O‰ËÁ›Â˜ ¯Ú‹Ûˆ˜
Instrukcja obs¬ugi
INSTALLATION
Connections general
Analog connections
For recording the following inputs are present:
- Digital optical input.
- Digital coaxial input 1.
- Digital coaxial input 2.
- Analog input.
Analog connection is required for playback of CDs (use cable
2) and for recording from external analog sources
(use cable 1).
RECEIVER
For playback the following outputs are present:
- Digital coaxial output.
L
L
- Digital optical output.
- Analog output.
R
R
IN
OUT
TAPE
We advise you to connect these to the CD input on your
amplifier.
1
CD RECORDER
2
ANALOG
IN
OUT
The connections you make will depend upon the possibilities
your audio equipment offers. Please refer to the user manuals
for your other audio equipment first.
L
L
DIGITAL
OUT
IN1
IN2
R
OPTICAL
IN
R
OUT
Digital recordings (optical or coaxial) give the best
performance in audio and usability (e.g. auto-track).
(The digital optical connection is less sensitive to external
disturbances).
If your equipment does not offer digital connections, the high
quality Analog-Digital-Convertor of your CD recorder will
ensure very good audio performance when recordings are
made from the analog input.
Use the audio cables supplied. Connect the red plugs to the
R sockets, and the white plugs to the L sockets.
1 For recording, connect cable 1 between the ANALOG IN-
sockets on the CD recorder and the CDR LINE- or TAPE OUT-
sockets of an amplifier.
Playback via the digital coaxial output of the CD recorder
gives the best audio performance.
If your equipment does not offer digital connections, the high
quality Digital-Analog-Convertor of the CD recorder ensures a
very good sound quality via the analog output.
Note: For recording directly from a CD player, the ANALOG IN
sockets of the CD recorder should be connected to the
analog output of the CD player.
2 For playback, connect cable 2 between the ANALOG OUT-
sockets on the CD recorder and the input sockets of an
amplifier e.g. TAPE IN, CDR or AUX.
We advise you to always establish both digital and analog
connections. In this way you can always make analog
recordings when digital recording is not possible.
Note: Never use the PHONO input.
We have described the most common ways of connecting the
CD recorder. If you still have difficulties with the connections
you can always contact the Philips Consumer Service desk in
your country.
11
INSTALLATION
Digital coaxial connections
Digital optical connections
Digital coaxial connection is only required in case you wish to
record from a CD player with a digital coaxial output.
Digital optical connection is only required in case you wish to
record from a CD player with a digital optical output.
RECEIVER
RECEIVER
L
L
L
R
L
R
IN
OUT
MAINS
R
TAPE
R
IN
OUT
TAPE
CD RECORDER
CD RECORDER
ANALOG
IN
OUT
ANALOG
L
DIGITAL
OUT
IN
OUT
IN1
L
IN2
OPTICAL
L
IN
DIGITAL
OUT
R
IN1
OUT
IN2
R
OPTICAL
MAINS
IN
R
OUT
4
CD PLA
CD PLA
YER
YER
3
L
MAINS
L
R
OUT
ANALOG
R
OUT
DIGITAL
OUT
ANALOG
OUT
OPTICAL
OUT
DIGITAL
Use the digital coaxial cable supplied.
When connecting the Digital
Optical cable, make sure it
is fully inserted until
1 For recording, connect the cable 3 between the DIGITAL
IN-1 socket on the CD recorder and the DIGITAL OUT-socket
of a CD player.
there is a click.
•If required you can connect an extra digital device (e.g.a
DAT or DCC recorder) to the DIGITAL IN 2 socket of the
recorder.
1 Remove the dust caps from the digital optical connection.
(We recommend you save the cap).
Note: Your CD recorder is equipped with a digital coaxial
output (DIGITAL OUT). This output can be used for
digital playback.
2 For recording, connect a fibre-optic cable 4 between the
digital OPTICAL IN socket of the CD recorder and the
digital-optical output of a CD player.
Note: Your CD recorder is equipped with a digital OPTICAL
output. This output can be used for digital playback.
12
INSTALLATION
Power supply
Inserting batteries in the remote control
1 Plug the power cord supplied into the MAINS connector on
the CD recorder, then into a mains socket.
2 Press ON/OFF.
➜ The recorder is now in Standby mode.
1 Open the battery compartment cover.
3 Press any key to activate the recorder.
2 Insert 2 batteries (“AA”, LR-6 or UM-3; as supplied) as
shown.
Note:
- The CD recorder will automatically adjust to the local mains
voltage.
3 Replace the cover.
- When the CD recorder is in the Standby mode, it is still
consuming some power. If you wish to disconnect your
recorder completely from the mains, press ON/OFF on the
recorder front.
Note: We recommend you use 2 batteries of the same type
and condition.
Batteries contain chemical substances, so they should
be disposed of properly.
Setup recommendations
- Place the CD recorder on a solid, vibration free surface.
- Do not place the CD recorder near a source of heat or in
direct sunlight.
- Do not use the CD recorder under extremely damp
conditions.
- If the CD recorder is placed in a cabinet, make sure that a
2.5 cm space remains free on all sides of the CD
recorder/player for proper ventilation.
13
|