1
)
English
SIDE PANEL (See
Clock Radio
AJ100
1
1
2
8 TUNING +/- tunes to radio stations
–
SUPPLIED ACCESSORIES
9
Pigtail – improves FM reception
0 DC 7.5V socket for AC/DC 7.5V adapter
! SET AL / PRESET 1 sets AL time
– 1 X certified AC 7.5V adapter
(Input: 230-240V ~ 50Hz 30mA, Output: 7.5V
–
–
250mA)
User manual
– stores, recalls and shows station 1
@ SET AL / PRESET 2
–
sets AL time
– stores, recalls and shows station 2
1
TOP AND FRONT PANEL (See
)
# MIN + / PRESET 3
–
adjusts the minutes for clock and alarm times
1
REPEAT ALARM / BRIGHTNESS CONTROL
– switches off the alarm for a 9 minute period
– changes the brightness of the display illumination
– stops SLEEP function
– stores, recalls and shows station 3
$ SET TIME / PRESET 4 – sets the clock time
5
6
3
4
– stores, recalls and shows station 4
% HR + / PRESET 5 – adjusts the hours for the clock and alarm times
– stores, recalls and shows station 5
2 DISPLAY
–
shows clock/alarm times and status of the set
^ VOLUME
–
adjusts the sound level
3 ALARM RESET / SLEEP
– stops active alarm for 24 hours
– activates the radio for sleep function
–
displays/adjusts/switches off sleep timer
switches on/off buzzer mode
– displays time
7
4
ALARM
–
5 RADIO ON/OFF
Helpful hints: To avoid damage to the set, use only the adapter supplied!
– switches the radio on/off; displays radio frequency
– switches off sleep timer
The type plate is located on the bottom of the set.
!
@
#
8
9
6
7
ALARM
–
switches on/off radio mode
– displays time
RESET – press if the set / display does not react to operation of any button
This product complies with the radio interference requirements of the
European Community.
$
%
CAUTION
- High voltage! Do not open.You run the risk of getting an electric
shock. The machine does not contain any user-serviceable parts.
0
- Modification of the product could result in hazardous radiation of
EMC or other unsafe operation.
^
SELF-POWERED BACK-UP
RADIO
Clock radio
2
1
Press RADIO ON/OFF once to switch on the radio.
™Display shows the radio frequency of the last selected waveband briefly
before returning to the clock time. Your preset station is also shown if you
2
The self-powered back-up conveniently allows your preset stations, alarm and clock
time settings to be stored for up to 3 minutes when there is a power interruption e.g.
AC power failure. The complete clock radio and backlight illumination will be switched
off.
Meet Philips at the Internet
are listening to a preset. (See
)
2
3
Adjust the sound using VOLUME.
To select preset stations, press the respective PRESET button (1-5) once or
repeatedly.
If power supply returns after 3 minutes and the display shows:
English
•
clock time blinking - indicates you need to re-adjust the clock time.
BASIC FEATURES
4
Press RADIO ON/OFF to switch off.
Reset
TUNING TO RADIO STATONS
Automatic tuning
3
4
Should your set receive external interference e.g. static electricity from carpets, thun-
derstorms, etc. RESET allows you to clear all previous settings and start up again.
•
Press TUNING +/- one second or more to tune to your station.
•
Use a ballpoint pen to press the RESET hole found on the bottom of the set.
™The radio automatically tunes to a station of sufficient reception.
Manual tuning
Press TUNING +/- briefly or repeatedly until you reach the desired frequency.
Illumination brightness
Press REPEAT ALARM / BRIGHTNESS CONTROL once or more.
•
•
The brightness of the display can be adjusted:
Bright ➟ Low ➟ Off ➟ Bright
To improve reception:
For FM, extend and position the pigtail fully to obtain optimum reception.
.
STORING AND USING PRESET STATIONS
SETTING THE CLOCK
You can store up to a total of 5 FM radio stations in the memory.
The time is displayed using the 24-hour clock.
1. Check the radio is switched off.
2. Press SET TIME to enter the clock setting mode.
3. Hold down or press HR + or MIN + repeatedly to set and adjust the hours and
minutes respectively. Release HR + or MIN + when you have reached the cor-
rect setting.
1
2
Tune to your desired station (see TUNING TO RADIO STATIONS).
To store a preset, hold down briefly on a PRESET button 1-5 until you hear a double
beep.
™Display shows the preset number of your station.
3
Repeat steps 1 and 2 to store your other stations.
•
4
You can overwrite a preset station by storing another frequency in its place.
Press a PRESET button 1-5 to listen to a preset station.
4. Press SET TIME to confirm.
Printed in China
PDCC-JW-0703
|