Always there to help you
Register your product and get support at
Question?
Contact
Philips
HTL2111A
User manual
•
•
Never insert objects into the ventilation
slots or other openings on the product.
Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Disconnect the product from the power
outlet before lightning storms.
When you disconnect the power cord,
always pull the plug, never the cable.
1 Important
Read and understand all instructions before you
use your product. If damage is caused by failure
to follow instructions, the warranty does not
apply.
•
•
Risk of short circuit or fire!
Help and support
•
Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
com/support to:
•
•
•
download the user manual and the quick
start guide
watch video tutorials (available only for
selected models)
find answers to frequently answered
questions (FAQs)
Risk of injury or damage to this product!
•
Never place the product or any objects
on power cords or on other electrical
equipment.
•
•
email us a question
chat with our support representative.
•
If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
Parts of this product can be made of
glass. Handle with care to avoid injury and
damage.
Follow the instructions on the website to select
your language, and then enter your product
model number.
Alternatively, you can contact Consumer Care
in your country. Before you contact, note down
the model number and serial number of your
product.You can find this information on the
back or bottom of your product.
•
Risk of overheating!
•
Never install this product in a confined
space.Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Safety
Risk of electric shock or fire!
Risk of contamination!
•
Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Consumer Care to
have the product checked before use.
Never place the product and accessories
near naked flames or other heat sources,
including direct sunlight.
•
Do not mix batteries (old and new or
carbon and alkaine, etc.).
•
Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
•
•
Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
Batteries contain chemical substances, they
should be disposed of properly.
•
2
EN
Risk of swallowing batteries!
•
The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local
separate collection system for electrical and
electronic products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste.
•
•
If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after
you replace the battery.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
•
If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed with normal household waste.
Please inform yourself about the local rules
on separate collection of batteries because
correct disposal helps to prevent negative
consequences for the environmental and
human health.
This is CLASS II apparatus with double
insulation, and no protective earth provided.
Care for your product
Compliance
Use only microfiber cloth to clean the product.
Care of the environment
This product complies with the radio
interference requirements of the European
Community.
Hereby,WOOX Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions
of Directive 1999/5/EC.You can find the
com.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
EN
3
Trademarks
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
The Bluetooth word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by WOOX
Innovations is under license. Other trademarks
and trade names are those of their respective
owners.
4
EN
2 Your SoundBar
Remote control
This section includes an overview of the
remote control.
Congratulations on your purchase, and
welcome to Philips!To fully benefit from
the support that Philips offers, register your
a
b
Main unit
This section includes an overview of the main
unit.
g
f
c
d
a
b
a SURR indicator
e
Lights up when you selectVirtual Surround
sound.
b Source indicators
•
•
•
OPTICAL: Lights up when you switch
to optical input source.
AUX: Lights up when you switch to
analog input source.
COAXIAL / AUDIO IN
Lights up when you switch to coaxial
input source.
Lights up when you switch to audio
input source (3.5mm jack).
Bluetooth
a
(Standby-On)
•
Switch the SoundBar on or to standby.
Lights up when you switch to
Bluetooth mode and Bluetooth devices
are paired.
Blinks when you switch to Bluetooth
mode and Bluetooth devices are not
paired.
b Source buttons
•
•
•
AUX: Switch your audio source to the
AUX connection.
USB: Switch your audio source to the
USB connection.
COAX: Switch your audio source to
the coaxial connection.
EN
5
•
•
•
AUDIO-IN: Switch your audio source
to audio in connection.
Bluetooth: Switch to Bluetooth
mode.
OPTICAL: Switch your audio source
to the optical connection.
Rear connectors
c TREBLE +/-
Increase or decrease treble.
d SURR
Toggle between stereo and virtual
surround sound.
e
a
b c
d
Mute or restore volume.
f BASS +/-
Increase or decrease bass.
a AUDIO IN-AUX
Connect to an analog audio output on the
TV or an analog device.
g VOLUME +/-
Increase or decrease volume.
b DIGITAL IN-OPTICAL
Connect to an optical audio output on the
TV or a digital device.
Connectors
c DIGITAL IN-COAXIAL
Connect to a coaxial audio output on the
TV or a digital device.
This section includes an overview of the
connectors available on your SoundBar.
d AC MAINS~
Side right
Connect to the power supply.
a
b
a
(USB)
Audio input from a USB storage device.
b AUDIO IN
Audio input from an MP3 player (3.5mm
jack).
6
EN
3 Connect
Connect audio fromTV and
other devices
This section helps you connect your SoundBar
to aTV and other devices.
For information about the basic connections of
your SoundBar and accessories, see the quick
start guide.
Play audio fromTV or other devices through
your Soundbar.
Use the best quality connection available on
yourTV and other devices.
Option 1: Connect audio through a
digital optical cable
Note
• For identification and supply ratings, refer to the type
plate at the back or bottom of the product.
Best quality audio
• Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
TV
Placement
Place your Soundbar as shown below.
1 Using an optical cable, connect the
OPTICAL connector on your SoundBar to
the OPTICAL OUT connector on theTV
or other device.
•
The digital optical connector might be
labeled SPDIF or SPDIF OUT.
Option 2: Connect audio through a
digital coaxial cable
Good quality audio
1 Using a coaxial cable, connect the
COAXIAL connector on your SoundBar
to the COAXIAL/DIGITAL OUT
connector on theTV or other device.
EN
7
•
The digital coaxial connector might be
labeled DIGITAL AUDIO OUT.
Option 3: Connect audio through
analog audio cables
Basic quality audio
1 Using an analog cable, connect the AUX
connectors on your SoundBar to the
AUDIO OUT connectors on theTV or
other device.
DVD
8
EN
Equalizer
4 Use your
SoundBar
Change the high frequency (treble) and low
frequency (bass) settings of the SoundBar.
1 Press TREBLE +/- or BASS +/- to change
the frequency.
This section helps you use the SoundBar to play
audio from connected devices.
Before you start
» All Source indicators on the main unit
blink twice when treble or bass is set
to the maximum or minimum value.
•
Make the necessary connections described
in the Quick Start Guide or download
support.
MP3 player
•
Switch the SoundBar to the correct source
for other devices.
Connect your MP3 player to play your audio
files or music.
What you need
•
•
An MP3 player.
A 3.5mm stereo audio cable.
Adjust the volume
1 Using the 3.5mm stereo audio cable,
connect the MP3 player to the AUDIO IN
connector on your SoundBar.
1 Press VOLUME +/- to increase or
decrease a volume level.
•
•
To mute sound, press (MUTE).
To restore the sound, press (MUTE)
again or press VOLUME +/-.
2 Press AUDIO-IN.
3 Press the buttons on the MP3 player to
» All Source indicators on the main unit
blink twice when a volume is set to the
maximum or minimum value.
select and play audio files or music.
USB storage devices
Choose your sound
Enjoy audio on a USB storage device, such as an
MP3 player and USB flash memory, etc.
What you need
This section helps you choose the ideal sound
for your video or music.
•
A USB storage device that is formatted
for FAT file systems, and complies with the
Mass Storage Class.
Surround sound mode
•
An MP3 or WMA file on a USB storage
device
Experience an immersive audio experience with
surround sound modes.
1 Connect a USB storage device to the
1 Press SURR to turn surround mode on
SoundBar.
or off.
2 Press USB on the remote control.
•
On: Create a surround listening
experience.
» The play starts after a few seconds.
•
Off:Two-channel stereo sound. Ideal
for listening to music.
EN
9
user manual of the Bluetooth device on
how to enable Bluetooth).
Note
•
When prompted for a password, enter
"0000".
• This product may not be compatible with certain types
of USB storage device.
• If you use a USB extension cable, USB HUB, or USB
multi-reader, the USB storage device may not be
recognized.
» During connection, the Bluetooth
indicator blinks at a lower rate.
• Digital camera PTP protocols are not supported.
• Do not remove the USB storage device while it is
being read.
• DRM-protected music files (MP3,WMA) are not
supported.
3 Wait until the Bluetooth lights up.
» If the connection fails, the Bluetooth
indicator blinks continually at a lower
rate.
• Support a USB port: 5V , 500mA.
4
Select and play audio files or music on
your Bluetooth device.
•
During play, if a call is coming, music
play is paused. Play resumes when the
call ends.
Auto standby
5 To exit Bluetooth, select other source.
When playing media from a connected device,
the SoundBar automatically switches to standby
if:
•
When your switch back to Bluetooth
mode, Bluetooth connection remains
active.
•
•
no button is pressed for 30 minutes, and
no audio play from a connected device.
Note
• The music streaming may be interrupted by obstacles
between the device and SoundBar, such as wall, metallic
casing that covers the device, or other devices nearby
that operate in the same frequency.
• If you want to connect your SoundBar with another
Bluetooth device, disable the currently connected
Bluetooth device.
Play audio through Bluetooth
Through Bluetooth, connect the SoundBar with
your Bluetooth device (such as an iPad, iPhone,
iPod touch,Android phone, or laptop), and then
you can listen to the audio files stored on the
device through your SoundBar speakers.
What you need
•
A Bluetooth device which supports
Bluetooth profile A2DP, and with Bluetooth
version as 2.1 + EDR.
The operational range between the
SoundBar and a Bluetooth device is
approximately 10 meters (30 feet).
Apply factory settings
You can reset your SoundBar to the default
setting mode.
•
1 In mute mode, quickly press AUX twice.
» The factory settings is restored.
1 Press Bluetooth on the remote control
to switch the SoundBar to Bluetooth
mode.
» The Bluetooth indicator blinks at a fast
rate.
2 On the Bluetooth device, switch on
Bluetooth, search for and select PHILIPS
HTL2111A to start connection (see the
10 EN
5 Wall mount
Note
• Improper wall mounting may result in accident, injury or
damage. If you have any query, contact Consumer Care
in your country.
• Before wall mounting, make sure the wall can support
the weight of your SoundBar.
Screw length/diameter
Depending on the type of wall mounting your
SoundBar, make sure that you use screws of a
suitable length and diameter.
3 - 3.5mm
> 25mm
For information about how to wall mount your
SoundBar, see the quick start guide.
EN 11
Bluetooth
6 Product
specifications
•
•
Bluetooth profiles:A2DP
Bluetooth version: 2.1 + EDR
Main unit
•
•
•
•
•
•
Power supply: 220-240V~, 50 Hz
Note
Power consumption: 40 W
Standby power consumption: ≤ 0.5 W
Speaker impedance: 8 ohm (full range)
Speaker drivers: 4 x 54.5 mm (2")
Dimensions (WxHxD):
• Specifications and design are subject to change without
notice.
845 x 74.5 x 94 mm
Weight: 2.0 kg
Amplifier
•
•
•
•
•
•
Total output power: 40W RMS (+/- 0.5 dB,
10%THD)
Frequency response: 20 Hz-20 kHz /
±3 dB
Signal-to-noise ratio: > 65 dB (CCIR) /
(A-weighted)
Input sensitivity:
Operating temperature and humidity:
0°C to 45°C, 5% to 90% Humidity for all
climates
Storage temperature and humidity: -40 °C
to 70 °C, 5% to 95%
•
Remote control batteries
•
•
AUX: 2Vrms
AUDIO IN: 1Vrms
•
1 x CR2025
Audio
•
S/PDIF Digital audio input:
•
•
Coaxial: IEC 60958-3
Optical:TOSLINK
•
Sampling frequency:
•
MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz, 22
kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz
WMA: 44.1 kHz, 48 kHz
•
•
•
Constant bit rate:
•
•
MP3: 8 kbps-320 kbps
WMA: 64 kbps-192 kbps
Version:
WMA:V7,V8,V9
•
USB
•
•
Compatibility: Hi-Speed USB (2.0)
Class support: USB Mass Storage Class
(MSC)
•
•
File system: FAT16 and FAT32
Supports MP3 and WMA file formats
12 EN
Quality of audio play from a connected
Bluetooth device is poor.
7 Troubleshooting
•
The Bluetooth reception is poor. Move the
device closer to the SoundBar, or remove
any obstacle between the device and the
SoundBar.
Warning
The connected Bluetooth device connects and
disconnects constantly.
• Risk of electric shock. Never remove the casing of the
product.
•
The Bluetooth reception is poor. Move the
device closer to the SoundBar, or remove
any obstacle between the device and the
SoundBar.
To keep the warranty valid, never try to repair
the product yourself.
If you have problems using this product, check
the following points before you request service.
If you still have a problem, get support at www.
philips.com/support.
•
•
Turn off Wi-Fi function on the Bluetooth
device to avoid interference.
For some Bluetooth, the Bluetooth
connection can be deactivated
automatically to save power.This does not
indicate any malfunction of the SoundBar.
Sound
No sound from SoundBar speakers.
•
Connect the audio cable from your
SoundBar to yourTV or other devices.
Reset your SoundBar to its factory settings.
On the remote control, select the correct
audio input.
•
•
•
Make sure that the SoundBar is not muted.
Distorted sound or echo.
•
If you play audio from theTV through the
SoundBar, make sure that theTV is muted.
Bluetooth
A device cannot connect with the SoundBar.
•
The device does not support the
compatible profiles required for the
SoundBar.
•
You have not enabled the Bluetooth
function of the device. See the user manual
of the device on how to enable the
function.
•
•
The device is not correctly connected.
Connect the device correctly. (see 'Play
The SoundBar is already connected with
another Bluetooth device. Disconnect the
connected device, then try again.
EN 13
Specifications are subject to change without notice
2013 ©WOOX Innovations Limited.All rights reserved.
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used byWOOX Innovations Limited under license from Koninklijke Philips N.V.
HTL2111A_12_UM_V1.0
|