Philips Indoor Furnishings Wall Mounting User Manual

Quick Start Guide  
CONTENTS  
INSTALLING LCD TV ON THE WALL . .1 TUNER MODE CONTROL . . . . . . . . . . . . . 5  
UNFOLD THE BASE. . . . . . . . . . . . . . . 1 AUTO PROGRAM (SETTING UP  
TV CHANNEL INSTALLATION . . . . . . . .2 CHANNELS) . . . . . . . . . . . . . . . . . . . . 5  
PRESENTATION OF THE LCD TV . . . . . 2 CABLE BOX (WITH RF IN/OUTPUTS) . . 6  
ACCESSORIES. . . . . . . . . . . . . . . . . . . .3 CABLE BOX (WITH AUDIO/VIDEO  
BATTERY INSTALLATION . . . . . . . . . . . . 3 OUTPUTS) . . . . . . . . . . . . . . . . . . . . . 6  
REMOTE CONTROL OPERATION . . . . . .3 S-VIDEO CONNECTIONS . . . . . . . . . . . 7  
ANTENNA TV . . . . . . . . . . . . . . . . . . 4 HD CONNECTIONS . . . . . . . . . . . . . . 7  
BASIC CABLE TV CONNECTION . . . . . 4 PC (MONITOR) INPUTS . . . . . . . . . . . 8  
INSTALLING LCDTV ON THE WALL  
The stand of your LCD TV complies with the VESA standard, if you intend to install the LCD TV on the wall,  
please consult a professional technician for proper installing.  
Wall Mounting of your LCD TV :  
Put your LCD TV set on a safe and flat surface, then  
fold the base backward.  
Note: To fold the base requires a degree fo force.  
1
Use for the TV set a Vesa compliant wall mount (not included).  
(For 20 inch: 100x100 mm)  
2
3
Use for installation by a professional technician.  
(20 inch: 100x100 mm)  
Note: The manufacture accepts no liability, ensure installation is  
done by a professional technician.  
UNFOLD THE BASE  
Expanding the base requires a degree of force; please use sufficient force to unfold the base.  
When unfolding the base, place the TV on a flat, sturdy surface before expanding the base.  
2
1
3
Download from Www.Somanuals.com1. All Manuals Search And Download.  
3138 155 24532  
ACCESSORIES  
BATTERY INSTALLATION  
Remove the battery compartment lid on  
the bottom of the remote control.  
1
2
Place lithium cell in the remote control.  
Be sure the (+) and (-) ends of the  
batteries line up as marked inside the  
battery (CR2025) compartment.  
2
Reattach the battery  
compartment lid.  
3
Owner`s Manual & Quick Start Guide  
Power adapter & cable  
d
r
C
a
C
d
r
e
a
e
t
1
3
n
a
y
t
n
r
a
u
G
a
r
r
a
W
W
(/79)  
(/98)  
Tuner L-Adapter  
Warranty Card  
REMOTE CONTROL OPERATION  
Unused key  
Press to go to previously selected channel.  
Power button  
Press to turn the LCD TV on or off.  
Sleep button  
A/CH  
Press to set the LCD TV to turn itself off within a  
certain time.  
I-II button / Sound mode  
Press repeatedly to select Mono,  
Stereo, Dual I, Dual II, Nicam Mono, Nicam Stereo,  
Nicam Dual I, Nicam Dual II.  
Teletext keys  
Smart Sound button  
Picture Format button  
Press repeatedly to select among the 4 settings;  
Personal, Voice, Music, or Theatre.  
Press the FORMAT button  
repeatedly to toggle among the three screen format  
sizes; 4:3, EXPAND 4:3, COMPRESS 16:9  
Menu button  
Press to activate onscreen menu, back to previous  
level inside the onscreen menu, or press to exit the  
onscreen menu.  
Smart Picture button  
Press repeatedly to select either  
Personal, Rich, Natural, Soft, or  
Multimedia picture setting.  
Volume button  
Press to increase or decrease the sound level  
Virtual Surround button  
Adds greater depth and dimension to TV sound.  
Select from ON or OFF.  
Mute button  
Press to eliminate or restore the LCD TV sound.  
Mute will appear on the screen when the sound is  
muted.  
Cursor Buttons  
(Left, Right, Up, Down)-  
Press these buttons to highlight, select, and adjust  
items on the TV’s on screen menu.  
Number buttons  
Press the number buttons for direct access to the  
TV channels. For a 2 digit channel, enter the 2nd  
digit after enter 1st digit.  
i
+
AV  
Channel button  
Press to adjust the channel up or down.  
Information button  
AV button  
Press to see the current channel number on the TV  
screen.  
Press to select the video input source:  
PC, TV, AV, S-Video, HD  
 
3
ANTENNA TV  
A combination antenna receives normal broadcast channels (VHF 2–13 and UHF 14–69). Your connection is easy because there is only  
one 75 Ω (ohm) antenna jack on the side of your TV, and that’s where the antenna goes.  
If your antenna has a round cable (75 ohm) on the end, then  
you’re ready to connect it to the LCD TV. If your antenna  
has flat, twin-lead wire (300 ohm), you first need to attach  
the antenna wires to the screws on a 300- to 75-ohm  
1
adapter(not supplied).  
Outdoor or Indoor Antenna  
(Combination VHF/UHF)  
DC Adapter  
Connect the antenna (or adapter) to one end of the  
2
supplied L-Adapter as shown, and connect the other end of  
the L-Adapter to the TV jack on the side of the LCD TV.  
Power  
Cable  
Plug the DC adapter into the DC IN 16V jack on the LCD  
TV. Plug the power cable into an outlet and switch TV set on.  
3
4
Run the AUTO PROGRAM function to set up the TV for the  
broadcast or cable channels available in your area. If you do  
not run the auto program function to set up the channels ,  
your television may not operate properly.  
Twin-lead  
wire to  
300-75  
adapter  
OR  
Antenna  
with 75 �  
cable  
H
ELPFUL
H
INT  
• Remember, an antenna or cable TV signal must first be connected to  
your LCD TV.  
• Please make sure that you have selected the TV mode with AV key  
on your remote control, before installing TV channels.  
BASIC CABLE TV CONNECTION  
Your Cable TV input into your home may be a single (75 ohm) cable or use a cable box decoder. In either case the connection is very  
simple. Follow the steps below to connect your cable signal to your new television.  
Direct cable connections:  
The Cable TV signal from  
Cable Company  
(75 coaxial cable)  
Connect the Cable TV signal to one end of the supplied  
L-Adapter as shown, and connect the other end of the  
adapter to the TV jack on the LCD TV.  
1
Plug the DC adapter into the DC IN 16V jack on the LCD  
TV. Plug the power cable into an outlet and switch TV set on.  
L Adapter  
2
3
DC Adapter  
Run the AUTO PROGRAM function to set up the TV for the  
broadcast or cable channels available in your area. If you do  
not run the auto program function to set up the channels ,  
your television may not operate properly.  
Power  
Cable  
H
ELPFUL
H
INT  
• Remember, an antenna or cable TV signal must first be connected to  
your LCD TV.  
• Please make sure that you have selected the TV mode with AV key  
on your remote control, before installing TV channels.  
 
4
AUTO PROGRAM (SETTING UP CHANNELS)  
Your LCD TV can automatically set itself for local area (or cable TV) channels. This makes it easy for you to select only the TV stations in  
your area by pressing the CH+ or CH- button.  
MAIN CONTROLA  
Press the MENU button on the remote control to show the  
1
PICTURE  
AUDIO  
LANGUAGE  
onscreen menu.  
AUTO PROGRAM  
MANUAL STORE  
CHANNEL SETTING  
FACTORY RESET  
A/CH  
FEATURES  
INSTALL  
Press the CURSOR DOWN button to  
highlight the INSTALL menu.  
2
3
4
5
6
1
6
Press the CURSOR RIGHT button  
to enter the INSTALL menu.  
Press the CURSOR DOWN button to  
highlight the AUTO PROGRAM control.  
INSTALL  
LANGUAGE  
AUTO PROGRAM  
MANUAL STORE  
CHANNEL SETTING  
FACTORY RESET  
START  
?
3
5
Press the CURSOR RIGHT button to start the AUTO PROGRAM scanning  
of channels.  
2
4
Press the MENU button repeatedly to clear the menu from the screen, after  
AUTO STORE has finished.  
AUTO STORE  
PLEASE WAIT  
PROG.FOUND  
FREQUENCY  
H
ELPFUL
H
INT  
0
MHZ  
i
+
Immediately after unpacking and plugging in your new television, run the auto  
program function to set up the TV for the broadcast or cable channels available in  
your area. If you do not run the auto program function to set up the channels ,  
your television may not operate properly.  
AV  
After you’ve run Auto Program, check out the results. Press the CH(+) or the CH(-)  
button and see which channels you can select.  
Remember, an antenna or cable TV signal must first be connected to your LCD TV.  
MANUAL STORE OF TV CHANNEL  
You can also choose to tune your TV channels. Manual tuning allows you to store each programme manually.  
MAIN CONTROLS  
Press the MENU button on the remote  
control to show the onscreen menu.  
PICTURE  
AUDIO  
FEATURES  
LANGUAGE  
1
2
AUTO PROGRAM  
MANUAL STORE  
CHANNEL SETTING  
FACTORY RESET  
INSTALL  
INSTALL  
LANGUAGE  
AUTO PROGRAM  
MANUAL STORE  
CHANNEL SETTING  
FACTORY RESET  
Press the CURSOR DOWN button to  
highlight the INSTALL menu, then press  
CURSOR RIGHT to enter.  
MANUAL STORE  
PROG. NO  
FINETUNE  
STORE  
Select the MANUAL STORE, then press the CURSOR RIGHT button to  
activate auto search channel frequence or press  
number button to show your desired  
MANUAL STORE  
A/CH  
3
XXX.XX MHZ  
MANUAL STORE  
PROG. NO  
FINETUNE  
STORE  
START  
?
1
8
channel frequence.  
After the channel frequence confirmed, select  
PROGRAM NO. by pressing CURSOR DOWN.  
4
5
6
MANUAL STORE  
MANUAL STORE  
PROG. NO  
FINETUNE  
STORE  
2
Press the number button or CURSOR RIGHT/LEFT to give the channel  
number.  
2
3
5
6
7
5
6
If the channel reception is not satisfactory, press CURSOR DOWN button  
to highlight the FINETUNE. then press CURSOR RIGHT/LEFT to adjust.  
Note: If the channel reception is satisfactory, please go to step 7.  
MANUAL STORE  
MANUAL STORE  
PROG. NO  
FINETUNE  
STORE  
60  
Press CURSOR DOWN to highlight STORE function. Press CURSOR  
RIGHT to confirm stored.  
2
4
6
7
i
+
7
8
AV  
MANUAL STORE  
Press the MENU button repeatedly to clear the menu from the screen.  
MANUAL STORE  
PROG. NO  
FINETUNE  
STORE  
3
STORED  
5
 
5
CABLE BOX (WITH RF IN / OUTPUTS):  
Connect the Cable TV signal to the IN jack (or RF IN or CABLE  
IN) on the Cable Box.  
1
2
3
The CableTV signal from  
the Cable Company  
Connect an RF coaxial cable (not supplied) to the OUT jack (or  
TO TV or RF OUT) of the Cable Box.  
OUTPUT  
CH  
3
4
CABLE  
IN  
TO TV  
Connect the other end of the coaxial cable to one end of the  
supplied L-Adapter as shown, and connect the other end of the  
adapter to the TV jack on the LCD TV.  
75  
Coaxial  
Cable  
Plug the DC adapter into the DC IN 16V jack on the LCD TV.  
Plug the power cable into an outlet and switch TV set on.  
4
5
Set the Channel 3/4 (or Output channel) switch of the Cable Box  
to 3 or 4. Set the TV to the same channel. When watching TV  
programming, change channels at the Cable Box, not the LCD TV.  
H
ELPFUL
H
INT  
VGA  
PC  
• Immediately after unpacking and plugging in your new television,  
run the auto program function to set up the TV for the broadcast  
or cable channels available in your area. If you do not run the auto  
program function to set up the channels , your television may not  
operate properly.  
DC Adapter  
• Please make sure that you have selected the TV mode with AV key  
on your remote control, before installing TV channels.  
Power  
Cable  
CABLE BOX (WITH AUDIO /VIDEO OUTPUTS):  
This connection will supply stereo sound to the LCD TV.  
Connect the Cable TV signal to the IN jack (or RF IN or CABLE  
IN) on the Cable Box.  
S -VIDEO  
1
2
AUDIO  
VIDEO  
Using an RCA-type video cable (not supplied) connect one end of  
the video cable to the Video Out jack of the Cable Box. Connect  
the other end of the cable to the yellow VIDEO jack on the side  
of the TV. Video cables are usually marked with yellow and are  
available from Philips or electronics retailers. Video jacks on most  
equipment are yellow.  
VGA  
Using RCA-type, stereo audio cables (not supplied), connect one  
end of the cables to the left and right Audio Out jacks of the Cable  
Box. Connect the other end of that cable to the Audio jack on the  
side of the LCD TV. Audio cables are usually marked with red and  
white and are available from Philips or electronics retailers. The  
right audio jack is red and the left audio jack is white. Match the  
cable colors to the jack colors.  
PC  
Video Cable  
3
DC Adapter  
Audio Cable  
Power  
Cable  
Cable  
Plug the DC adapter into the DC IN 16V jack on the LCD TV.  
Plug the power cable into an outlet and switch TV set on.  
TV signal  
4
Note: Use the AV button on the remote control to tune to the AV  
channel for the cable box signal. Once tuned, change channels at  
the cable box, not the television.  
OUTPUT  
CH  
3
4
L
R
CABLE  
IN  
VIDEO  
OUT  
TO  
TV  
AUDIO  
OUT  
When you watch programs using VCR, it’s recommended to select  
SOFT Mode via Smart picture.  
Cable Box  
 
6
S-VIDEO CONNECTIONS  
The S-Video connection on the rear of the LCD TV can provide you  
with better picture detail and clarity for the playback of accessory  
sources such as DBS (digital broadcast satellite), DVD (digital video  
discs), video games, and VHS VCR (video cassette recorder) tapes  
than the normal antenna picture connections.  
S
-
VIDEO  
AUDIO  
VIDEO  
 
�  
Connect an S-Video cable to the S-VIDEO jack of the other  
equipment (DVD Player, Camcorder, etc.) and to the S-VIDEO jack  
on the rear of the LCD TV.  
1
�  
�  
Connect RCA-style audio cables (usually red and white) to the  
AUDIO OUT (left and right) jacks on the other equipment.  
Connect the other end of the cables to the AUDIO jack on the  
side of the LCD TV.  
�  
�  
2
 
Plug the DC Adapter into the DC IN 16V jack on the LCD TV.  
Plug the power cable into an outlet. Turn on the LCD TV and other  
equipment.  
 
�  
 
�  
�  
3
�  
���  
�  
�  
���  
�  
�  
�  
�����  
�  
 
Press the AV buttons to set the LCD TV to its S-VIDEO mode.  
4
5
Press PLAY on the other equipment to view its material on the  
LCD TV.  
i
+
 
Note:  
The Philips LCD TV remote control can not be used to operate other video/audio  
equipment.  
The Audio jack of AV IN is shared between Video (CVBS) and S-Video signals. If Audio  
and Video is connected to S-Video input, you can still hear sound if you select Video via  
AV select, even there appears no image on screen.  
HD CONNECTIONS  
HD video input provide the highest possible color and  
picture resolution in the playback of digital signal source material,  
such as with DVD players. If you are using a HD (High Definition)  
receiver that can transmit high definition programming, the TV can  
accept those signals through the HD input located on the bottom of  
the TV.  
Connect the HD (Y, Pb, Pr) Video OUT jacks from the DVD player  
(or similar device) to the HD VIDEO Input jacks on the bottom of  
the LCD TV.  
COMPONENT  
VIDEO CABLES  
(Green, Blue, Red)  
1
Audio Cable  
Power Cable  
Connect the red and white AUDIO CABLES to the Audio (left  
ad right) output jacks on the rear of the accessory device to the  
AUDIO IN jack. Connect the other end of the cable to the Audio  
jack on the rear of LCD TV.  
2
 
Plug the DC Adapter into the DC IN 16 V jack on the LCD TV.  
Plug the power cable into an outlet. Turn on the LCD TV and other  
equipment.  
3
COMP  
S-VIDEO VIDEO AUDIO  
R
L
Pb  
Y
OUT  
OUT  
OUT  
Press the AV button on the remote control to select HD. HD will  
appear in the upper left corner on the TV screen.  
Pr  
4
Insert a DVD disc into the DVD player and press the PLAY button  
5
on the DVD Player.  
i
+
 
ACCESSORY DEVICE  
EQUIPPED WITH COMPONENT  
VIDEO OUTPUTS.  
Note:  
The Philips LCD TV remote control can not be used to operate  
other video/audio equipment.  
 
7
PC (MONITOR) INPUTS:  
This LCD TV can be used as a PC. Your computer will have to be  
equipped with a VGA type video output and interface cable (not  
supplied). (One end with VGA type connector, the other end with  
D-SUB type connector.)  
Connect VGA end of the interface cable (not supplied) to the  
computer, while connecting the other ends to the D-SUB INPUT  
jack on the LCD TV.  
1
 
Although audio connections are not required, the LCD TV can  
reproduce the computers audio out by an AUDIO ADAPTER to  
the Audio output jack on the computer (if available) while  
connecting the other ends of the Audio cables to the PC AUDIO  
Jacks on the bottom of the TV.  
2
�  
�  
Plug the DC Adapter into the DC IN 16V jack on the LCD TV. Plug  
�  
3
4
the power cable into an outlet. Turn on the LCD TV and PC.  
�  
Press the AV button until PC MODE appears on the screen.  
i
+
 
 
H
ELPFUL
H
INT  
• For PC function, it just accepts analog input via D-Sub type connector.  
 
8

Philips CRT Television 10 42PF9641D 10 User Manual
Philips Stereo System FW V795 User Manual
Philips Stereo System MZ3 User Manual
Pioneer DVD Recorder DVD V7400 User Manual
Polycom Saw 2000 4000 User Manual
Poulan Trimmer S17DE User Manual
Preh Computer Monitor MCI 15 User Manual
Promise Technology Network Card C6101SSWP000000 2 User Manual
ProScan TV Receiver RLED2445A B User Manual
PYLE Audio Car Video System PLVW1782R User Manual