Always there to help you
Register your product and get support at
DS7530/12
Question?
Contact
Philips
User manual
Contents
1 Important
2
2 Your Docking Speaker
Introduction
3
3
3
3
What's in the box
Overview of the main unit
3 Get started
Connect power
Turn on
4
4
4
4 Play
5
5
5
6
6
Play from iPod/iPhone
Play from Bluetooth device
Play from an external audio device
Adjust volume
5 Product information
7
7
Specifications
6 Troubleshooting
8
8
About Bluetooth device
7 Notice
9
EN
1
•
•
Apparatus shall not be exposed to
dripping or splashing.
1 Important
Do not place any sources of danger on the
apparatus (e.g. liquid filled objects, lighted
candles).
•
•
Follow all instructions.
Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
•
Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.
•
•
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Warning
• Never remove the casing of this apparatus.
• Never place this apparatus on other electrical
Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
equipment.
• Keep this device away from direct sunlight, naked
flames or heat.
• Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect the apparatus from
the power.
•
•
Only use attachments/accessories specified
by the manufacturer.
Unplug this apparatus during lightning
storms or when unused for long periods
of time.
•
Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
•
Battery usage CAUTION –To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
•
•
•
•
Install all batteries correctly, + and - as
marked on the unit.
Do not mix batteries (old and new or
carbon and alkaline, etc.).
Remove batteries when the unit is not
used for a long time.
Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
2
EN
2 Your Docking
Speaker
Overview of the main unit
a
d
c
b
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
e
f
h
g
If you contact Philips, you will be asked for the
model and serial number of this apparatus.The
model number and serial number are on the
back of the apparatus.Write the numbers here:
a
Bluetooth
•
Enable or disable Bluetooth function.
Model No. __________________________
Serial No. ___________________________
b Dock for the iPod/iPhone
c ON/OFF
•
Switch on/off the docking speaker.
Introduction
d -VOLUME +
•
Adjust volume.
With this docking speaker, you can enjoy audio
from the iPod/iPhone, Bluetooth devices, and
other external audio devices.
e DC IN
•
Connect power.
f AUX IN
•
Connect an external audio device.
What's in the box
g Battery compartment
h Stand foot
Check and identify the contents of your
package:
•
•
•
•
Main unit
AC power adapter
Quick start guide
Safety sheet
EN
3
1 Open the battery compartment.
3 Get started
2 Insert 4 x 1.5V AA batteries with correct
polarity (+/-) as indicated.
3 Close the battery compartment.
Always follow the instructions in this chapter in
sequence.
PUSH
Connect power
This docking speaker can be powered by either
AC power or batteries.
Option 1:AC power
Caution
• Risk of product damage! Make sure that the power
supply voltage matches the voltage printed on the back
of the unit.
• Risk of electric shock! When you unplug the AC
adapter, always pull the plug from the socket. Never
pull the cord.
Connect the AC power adapter to:
•
the power socket at the back of the
docking speaker.
Turn on
•
the wall socket.
Switch the power button to ON position to
turn on the docking speaker.
» The LED indicator lights up.
Switch to standby mode
The docking speaker switches to economic
standby mode in the following situation:
•
The speaker is idle for 15 minutes
when powered by AC supply;
Option 2: Battery power
•
The iPod/iPhone or external audio
device is disconnected when the
speaker is operated on batteries.
Caution
» The LED indicator lights off.
• Risk of explosion! Keep batteries away from heat,
sunshine or fire. Never discard batteries in fire.
• Remove batteries if they are exhausted or will not be
used for a long time.
• Batteries contain chemical substances, so they should
be disposed of properly.
4
EN
3
For first-time use, you will be asked to
install DockStudio app on your iPod/
iPhone.
4 Play
4 Tap [Yes] (yes) to accept the installation
request.
5 Follow the on-screen instructions to
Play from iPod/iPhone
complete the installation.
You can enjoy audio from your iPod/iPhone
through this docking speaker.
Compatible iPod/iPhone
The docking speaker supports the following
iPod and iPhone models:
Made for.
6 Launch the app after the installation.
•
•
•
iPod touch (2nd, 3rd, and 4th generation)
7 Play audio on your iPod/iPhone.
» You can hear audio from this docking
speaker.
iPod classic
iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th
generation)
•
•
•
•
iPhone 4S
iPhone 4
Charge the iPod/iPhone
iPhone 3GS
iPhone 3G
When the docking speaker is connected to
power, the docked iPod/iPhone begins to
charge automatically.
Listen to the iPod/iPhone
Play from Bluetooth device
Pair with Bluetooth devices
Philips DockStudio app brings a suite of new
features to your docking speaker, including
Internet radio and a multi-function alarm clock.
To enjoy more features, you are recommended
to install this free application.
Note
• Before you connect a Bluetooth device to this docking
speaker, familiarize yourself with the Bluetooth
capabilities of the device.
1 Switch the power button to ON position.
» The LED indicator lights up.
• The effective operation range between the docking
system and the paired device is approximately 10
meters (30 feet).
2 Insert the iPod/iPhone into the dock.
• Keep this docking speaker away from other electronic
devices that may cause interference.
1 Press Bluetooth to select Bluetooth
source.
» The Bluetooth button blinks.
EN
5
2 Turn on Bluetooth function on your device.
•
Deactivate Bluetooth function on
your device or move it beyond the
communication range.
•
Different devices may have different
way to activate Bluetooth.
Play from an external audio
device
With this docking speaker, you can also enjoy
audio from an external device such as an MP3
player.
Note
• Make sure that no iPod/iPhone is docked in the docking
speaker.
1
Connect an MP3 link cable (not supplied)
to:
•
•
the AUX IN socket at the back of the
docking speaker.
3 Scan Bluetooth devices that can pair with
your device.
the headphone socket on an external
device.
4 When “DS7530” is displayed on your
device, select it to start connection.
» Double beep tone confirmation is
heard and the Bluetooth button stops
blinking if connection is successful.
2 Play music on the device (see the device's
user manual).
» A different Bluetooth icon is displayed
Adjust volume
on your device.
5 Play music in your device.
» Music comes through the docking
speaker.
During play, press -VOLUME + to adjust
volume.
Tip
• If your Bluetooth device has been paired with DS7530
before, you just need to find out “DS7530” on your
Bluetooth menu, then confirm the connection.
To disconnect Bluetooth:
•
Press Bluetooth on the docking speaker
again.
6
EN
Max. load for iPod/
iPhone
Dimensions
5V 1 A
5 Product
information
- Main Unit (W x H
x D)
Weight
311 x 111 x 37.6mm
0.28 kg
Note
• Product information is subject to change without prior
notice.
- Main Unit
Specifications
Amplifier
Total Output Power
Signal to Noise Ratio
MP3 Link
2 x 5 W RMS
>60 dBA
0.6V RMS 22
kohm
Bluetooth
Standard
Bluetooth StandardVersion
2.1+EDR
Output power 4 dBm (Class 2)
Frequency
band
2.402 ~ 2.480 GHzISM Band
Range
10 m (free space)
General information
AC Power
Model:
S018KV0900200
(Philips);
Input: 100-240V ~
50/60Hz, 500mA;
Output: 9.0V 2000
mA
Operation Power
Consumption
<18 W
Eco Standby Power
Consumption
<0.5 W
EN
7
Cannot connect with the system.
6 Troubleshooting
•
The device does not support the profiles
required for the system.
•
The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
The system is not in the pairing mode.
The system is already connected with
another Bluetooth-enabled device.
Disconnect that device or all other
connected devices and then try again.
Warning
• Never remove the casing of this device.
•
•
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
The paired device connects and disconnects
constantly.
•
The Bluetooth reception is poor. Move
the device closer to the system or remove
any obstacle between the device and the
system.
•
For some devices, the Bluetooth
connection may be deactivated
automatically as a power-saving feature.
This does not indicate any malfunction of
the system.
No power
•
Ensure that the AC power plug of the unit
is connected properly.
•
Ensure that there is power at the AC
outlet.
No sound
•
Adjust the volume.
No response from the unit
•
Disconnect and reconnect the AC power
plug, then turn on the unit again.
About Bluetooth device
Music playback is unavailable on the system
even after successful Bluetooth connection.
•
The device cannot be used with the
system to play music.
The audio quality is poor after connection
with a Bluetooth-enabled device.
•
The Bluetooth reception is poor. Move
the device closer to the system or remove
any obstacle between the device and the
system.
8
EN
is covered by the European Directive 2002/96/
EC.
7 Notice
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
“Made for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specifically to iPod or
iPhone respectively, and has been certified by
the developer to meet Apple performance
standards.Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPod or iPhone
may affect wireless performance.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
This product complies with the radio
interference requirements of the European
Community.
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Note
• The type plate is located inside the battery
compartment of the unit.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
EN
9
Philips Consumer Lifestyle
HK-1225- DS7530
Year 2012
........................................................
(Report No. / Numéro du Rapport)
.........................................................................................
(Year in which the CE mark is affixed / Année au cours
de laquelle le marquage CE a été apposé)
EC DECLARATION OF CONFORMITY
(DECLARATION DE CONFORMITE CE)
We / Nous, PHILIPS CONSUMER LIFESTYLE B.V.
(Name / Nom de lÕentreprise)
TUSSENDIEPEN 4, 9206 AD DRACHTEN, THE NETHERLANDS
(address / adresse)
Declare under our responsibility that the electrical product(s):
(DĿclarons sous notre propre responsabilitĿ que le(s) produit(s) Ŀlectrique(s):)
PHILIPS
DS7530/05, /12
..................................
(brand name, nom de la marque)
.............................................
(Type version or model, référence ou modèle)
Docking Speaker
.................................................................
(product description, description du produit)
_
To which this declaration relates is in conformity with the following harmonized standards:
(Auquel cette dĿclaration se rapporte, est conforme aux normes harmonisĿes suivantes)
(title, number and date of issue of the standard / titre, numéro et date de parution de la norme)
EN60065:2002 + A1:2006 +A11:2008 +A2:2010 +A12:2011
EN 301 489-1 V1.8.1
EN 300 328 V1.7.1
EN55020:2007
EN61000-3-3:2008
EN62301:2005
EN 301 489-17 V2.1.1
EN55013:2001+A1:2003+A2:2006
EN61000-3-2:2006+A1:2009+A2:2009
EN 62479:2010
_
Following the provisions of :
(ConformĿment aux exigences essentielles et autres dispositions pertinentes de:)
_
1999/5/EC (R&TTE Directive)
2006/95/EC (Low Voltage Directive)
2004/108/EC (EMC Directive)
2011/65/EU (RoHS Directive)
2009/125/EC (ErP Directive)
- EC/1275/2008, EC/278/2009
And are produced under a quality scheme at least in conformity with ISO 9001 or CENELEC
Permanent Documents
(Et sont fabriquĿs conformĿment ˆ une qualitĿ au moins conforme ˆ la norme ISO 9001 ou aux Documents Permanents CENELEC)
SGS Fimko
CB
SGS GuangZhou
R&TTE Test
The Notified Body ................................................... performed ..................................................
(LÕOrganisme NotifiĿ)
(Name and number/ nom et numéro)
(a effectuĿ)
(description of intervention /
description de lÕintervention)
FI 7287
159004/1/G
And issued the certificate, ................................................................
(et a délivré le certificat)
(certificate number / numéro du certificat)
Remarks:
(Remarques:)
Drachten. Netherlands, June 19, 2012
...........................................................
(place,date / lieu, date)
A.Speelman, CL Compliance Manager
............................................................................................
(signature, name and function / signature, nom et fonction)
Philips Consumer Lifestyle
AMB 544-9056
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
DS7530_UM_12_EN_V1.0
|