1
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be reproduced, translated to
another language or stored in a retrieval system, or transmitted by any means,
electronic, mechanical, photocopying, recording, or otherwise, without prior written
permission. Windows is a registered trademark of Microsoft Inc.
Other brand or product names are trademarks of their respective holders.
2
3
TABLE OF CONTENTS
For your safety------------------------------------------------------ 5
Safety precautions -------------------------------------------6
Special notes on lcd monitors -----------------------------7
Before you operate the monitor --------------------------------7
Features --------------------------------------------------------7
Packing list ------------------------------------------------------7
Installation instructions -------------------------------------8
Controls and connectors ------------------------------------9
Adjusting the viewing angle------------------------------- 10
Operating instructions ------------------------------------------- 11
General instructions ----------------------------------------- 11
Front panel control -------------------------------------- 12
How to adjust a setting ----------------------------------- 13
Adjusting the picture ---------------------------------- 14-17
Plug and play ----------------------------------------------- 18
Technical support (FAQ) -------------------------------------- 19
Error message & possible solution ------------------- 20
Appendix -------------------------------------------------------------21
Specifications -------------------------------------------- 21
Factory preset timing table ------------------------------ 22
Connector pin assignment ------------------------------ 23-24
---------------25
Product registration and technical support
4
FOR YOUR SAFETY
Before operating the monitor, please read this manual thoroughly. This manual
should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1.
The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2.
3.
Shielded interface cables and AC power cord, if any, must be used in order to
comply with the emission limits.
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modification to this equipment. It is the responsibilities of
the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the cabinet.
Refer servicing to qualified personnel only.
5
ꢀ
PRECAUTIONS
ꢀ
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
ꢀ Do not place the monitor on an unstable cart, stand, or table. If the monitor falls,
it can injure a person and cause serious damage to the appliance. Use only a
cart or stand recommended by the manufacturer or sold with the monitor. If
you mount the monitor on a wall or shelf, use a mounting kit approved by the
manufacturer and follow the kit instructions.
ꢀ
Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it from
overheating, be sure these openings are not blocked or covered. Do not place
the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor
near or over a radiator or heat register. Do not place the monitor in a bookcase
or cabinet unless proper ventilation is provided.
ꢀ
ꢀ
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supplied to your home,
consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as a
safety feature. If your outlet does not accommodate the three-wire plug, have
an electrician install the correct outlet, or use an adapter to ground the
appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightening storm or when it will not be used for long
period of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in
fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor by yourself; opening or removing covers
can expose you to dangerous voltages and other hazards. Please refer all
servicing to qualified service personnel.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
To ensure satisfactory operation, use the monitor only with UL listed computers
which have appropriate configured receptacles marked between 100 - 240V AC,
Min. 5A.
The wall socket shall be installed near the equipment and shall be easily
accessible.
Important Recycle Instruction:
Lamp(s) inside this product contain mercury and must be recycled or disposed
of according to local, state or federal laws. For more information, contact the
electronic industries alliance at WWW.EIAE.ORG. For lamp specific disposal
information check WWW.LAMPRECYCLE.ORG.
6
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
ꢀ
Due to the nature of the fluorescent light, the screen may flicker during initial
use. Turn off the Power Switch and then turn it on again to make sure the flicker
disappears.
ꢀ
ꢀ
ꢀ
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes
of 0.01% or less such as a missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image when the same image has been displayed for
a long time. The monitor will slowly recover from this.
ꢀ
When the screen becomes black or flashing, or cannot illuminate any more,
contact your dealer or service center to replace parts. Don’t repair the screen by
yourself!
BEFORE YOU OPERATE THE MONITOR
FEATURES
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
21.5"(549mm) TFT Color LCD monitor
16:9 Widescreen
Crisp, Clear Display for Windows
Recommened Resolutions: 1920X 1080@60Hz
Ergonomic Design
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD monitor
2. Base
3. User's Guide
4. Power Cord
5. D-sub Cable
.
DVI Cable
6
7. Audio Cable
7
ꢀ
INSTALLATION INSTRUCTIONS
BASE
ꢀ
ꢀ
The monitor is supplied complete with a stand.If you prefer to wall mount the monitor,
please follow the instructions below to remove the stand.Be sure to include the stand
with the monitor if it is necessary to return the unit.
CAUTION
Put the monitor on a stable surface.The monitor may cause injury
or damage if it falls or is dropped.
Do not give a strong impact to the monitor.It may cause damage.
Ƶꢀ
ꢀ
Ƶꢀ
ƵꢀUnplug the monitor before removal or installation to avoid electric
shock or damage.
ꢀ
<Installation>
Put a piece of soft cloth on the able beforehand to
prevent the monitor from being scratched. Lay the
monitor flat on a table with front face down.
Insert stand iinto the monitor as shown in figure.
ķ
ĸ
Ĺ
Install the stand-base to the stand.
<Remove>
Put a piece of soft cloth on the table beforehand to
ķ
prevent the monitor from being scratched.Lay the
monitor flat on a table with front face down.
Press and hold the hooks inside,and pull the stand-
ĸ
Ĺ
base.
Insert thin stick into hole,Pull the stand while push
the stick.
8
ꢀ
CONTROLS AND CONNECTORS
SIGNAL CABLE
Connecting the Signal Cable: Plug one end of the signal cable to the LCD monitor
and the other end to a computer or a video source.
Connecting the Power Cord: Plug the AC-power cord one end to LCD monitor’s
AC input socket , the other end to Wall outlet.
Connecting the Audio Cable: Connect the audio cable between the monitor's
audio input and the PC's audio output.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
Figure 2 Connecting Cables
1. Power Cable
2. HDMI Cable
3
4
5
DVI Cable
D-SUB Cable
Audio Cable
ꢀ
9
ꢀ
ADJUSTING THE VIEWING ANGLE
ꢀ
ꢀ
ꢀ
For optimal viewing it is recommended to look at the full face of the monitor,
then adjust the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
You are able to adjust the monitor’s angle from -5ꢁ to 19ꢁ.
19°
-5°
Figure 3
NOTES
ꢀ
ꢀ
Do not touch the LCD screen when you change the angle. It may cause damage
or break the LCD screen.
Careful attention is required not to catch your fingers or hands when you
change the angle.
10
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are
located at front panel of the monitor (See Figure 4). By changing these settings, the
picture can be adjusted to your personal preferences.
ꢀ
ꢀ
ꢀ
The power cord should be connected.
Connect the video cable from the monitor to the video card.
Press the power button to turn on the monitor position. The power indicator
will light up.
Figure 4 External Control Button
EXTERNAL CONTROLS
1. Source/AutoAdjust/EXIT
button
ECO (-)
2.
3. Volume Hotkey(+)
4. Menu / Enter
5. Power Indicator
6. Power button
11
ꢀ
FRONT PANEL CONTROL
ꢀ
Power Button:
Press this button to switch ON/OFF monitor’s power.
ꢀ Power Indicator :
Blue --- Power On mode.
Orange --- Power saving mode.
ꢀ MENU/ENTER:
Activates OSD menu or function adjust confirm .
ꢀ
ECO/(-)
Activates the ECO control when the OSD is OFF or navigate through adjustment icons
when OSD is ON or adjust a function when function is activated.
ꢀ Volume/+:
Activates the volume control when the OSD is OFF or navigate through adjustment
icons when OSD is ON or adjust a function when function is activated.
ꢀ Source/Auto Adjust/Exit:
When the OSD is OFF, pressing Auto/Source button will toggle between sources.
Press continuously to select the input source indicated in the message bar.Press
Menu/Enter button to change to the selected source.
Auto configure hot key:(VGA input only) When the OSD is OFF,press and hold down
the button for 2 seconds to auto configure.
when OSD menu is ON, this button will act as a Exit Key (Exit OSD menu)
OSD Lock Function: To lock the OSD, press and hold the MENU button while the
monitor is off and then press power button to turn the monitor on. To un-lock the
OSD - press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on.
NOTES
ꢀ
Do not install the monitor in a location near heat sources such as radiators or air
ducts, or in a place subject to direct sunlight, or excessive dust or mechanical
vibration or shock.
ꢀ
ꢀ
ꢀ
Save the original shipping carton and packing materials, as they will come in
handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally packed at
the factory.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution. Never use strong solvents such as thinner, benzene, or
abrasive cleaners, since these will damage the cabinet. As a safety precaution,
always unplug the monitor before cleaning it.
It may cause permanent damage
.
ꢀ
ꢀ
do not scratch the screen with hard things,
Don’t leak liquid into monitor which will result in the damage of component
12
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press + or - to navigate through the functions. Once the desired function is
highlighted, press the MENU-button to activate it. If the function selected has a
sub-menu, press + or - again to navigate through the sub-menu functions.
Once the desired function is highlighted, press MENU-button to activate it.
3. Press + or - to change the settings of the selected function.
4. To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-3.
Figure 5 The OSD Message
13
ꢀ
ADJUSTING THE PICTURE
Main
Main Menu
Item
Sub
Menu
Menu
Icon
Description
Enhances Contrast Ratio
Note: When this function is turned "On" you cannot
adjust the current settings for Contrast, Brightness,
ECO mode or Gamma.
(VGA input
only)
(VGA input
only)
(VGA input
only)
(VGA input
only)
ꢀ
14
Main
Menu
Icon
Main Menu
Item
Sub
Menu
Description
15
Main
Menu
Icon
Main Menu
Item
Sub
Menu
Description
16
Main
Menu
Icon
Main Menu
Item
Sub
Menu
Description
17
PLUG AND PLAY
Plug & Play DDC 2B Feature
This monitor is equipped with VESA DDC 2B capabilities according to the VESA
DDC STANDARD. It allows the monitor to inform the host system of its identity and,
depending on the level of DDC used, communicate additional information about
its display capabilities.
The DDC 2B is a bidirectional data channel based on the I2C protocol. The host can
request EDID information over the DDC 2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE
MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics
and The Swedish Confederation Employees (NUTEK).
Standards Association (VESA)
consumption
This feature is designed to conserve electrical energy by reducing power
when
there is no video-input signal present. When there is no video input signal
this monitor, following a time-out period, will automatically switch to an OFF mode.
This reduces the monitor's internal power supply consumption. After the video
input signal is restored, full power is restored and the display is automatically
redrawn. The appearance is similar to a "Screen Saver" feature except the display is
completely off. The display is restored by pressing a key on the keyboard, or
clicking the mouse.
18
TECHNICAL SUPPORT (FAQ)
Problem & Question
Possible Solution
*Check if the Power Switch is in the ON
position
Power LED is not on
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
*Check if the Video Card is Plug & Play
compatible
No Plug & Play
Picture is fuzzy
*Check if the D-15 plug pin of Video Cable
is bent
*Adjust the Contrast and Brightness
Controls.
*Move electrical devices that may cause
electrical interference.
Picture bounces or a wave
pattern is present in the picture
*Computer Power Switch should be in the
ON position.
*Computer Video Card should be snugly
seated in its slot.
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS LOCK
LED. The LED should either turn ON or
OFF after hitting the CAPS LOCK key.
The power LED is ON but there’s
no video or no picture.
Missing one of the primary colors *Inspect the monitor’s video cable and
(RED, GREEN, or BLUE)
Screen image is not centered or
sized properly.
Picture has color defects
(white does not look white)
make sure that none of the pins are bent.
*Adjust pixel frequency (CLOCK) and FOCUS
or press hot-key (AUTO).
*Adjust RGB color or select color
temperature.
*Use win 95/98 shut-down mode Adjust
CLOCK and FOCUS or perform hot- key
(AUTO-key).
Horizontal or vertical disturbances
on the screen
CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal
sweep. If the frequency is not correct, the screen shows vertical stripes and the
picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment
the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down mode
pattern.
19
ꢀ
ERROR MESSAGE & POSSIBLE SOLUTION
NO SIGNAL :
1.
2.
Check that the signal-cable is properly connected , If the connector is loose,
tighten the connector’s screws.
Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table.
20
APPENDIX
SPECIFICATIONS
Driving system TFT 21.5"Color LCD
Viewable
546mm diagonal
Image Size
LCD Panel
Input
Pixel pitch 0.248˄H˅× 0.248˄v˅
R, G, B Analog Interface
DVI
HDMI
Video
Separate Sync. H/V TTL
H-Frequency Analog:24-80kHz,Digital:30kHz–83kHz
V-Frequency Analog&Digital:56-76Hz
170MHz
Dot Clock
Max. Resolution
Plug & Play
1920x1080@60Hz
VESA DDC2B TM
≤43W(TYP)
ON Mode
Power Consumption
OFF Mode ≤1W
D-Sub mini 15 pin, DVI-D 24 pin, HDMI
Input Connector
Analog:0.7Vp-p(Standard)75Ω, Positive
Digital:DVI(Digital Visual Interface
Standard Rev.1.0) compliance
Digital:HDMI(1.3)
Input Video Signal
Power Source
100~240VAC,50/60Hz
Operating Temp: 5° to 40°C
Environmental
Considerations
Storage
Temp.: -20° to 60°C
Operating umidity:15% to 90%
H
Dimension
Weight (N. W.)
Power Consumption ( Maximum )
512.7(W)X366.0(H)X181.5(D)
+
4.3kg 0.2kg
-
52Watts
UL cUL, CE , FCC B
/
Regulatory Compliance
21
ꢀ
FACTORY PRESET TIMING TABLE
HORIZONTAL
FREQUENCY(kHZ)
VERTICAL
FREQUENCY(Hz)
STANDARD
RESOLUTION
640 x 480
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
1280 x 1024
1440 x 900
1440 x 900
1680 x1050
1920 X1080
31.469
35
37.861
37.5
59.94
66.667
72.809
75
70.087
56.25
60.317
72.188
75
74.551
60.004
70.069
72.074
75.029
60.02
VGA
Mac VGA
Dos-mode
31.469
35.156
37.879
48.077
46.875
49.726
48.363
56.476
57.5
60.023
67.981
79.976
55.935
70.635
65.29
SVGA
Mac SVGA
XGA
SXGA
75.025
59.887
74.984
59.954
59.887
WXGA+
WSXGA+
HDTV
66.295
ꢀ
22
CONNECTOR PIN ASSIGNMENT
1
6
5
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
+5V
Detect Cable
Ground
DDC-Serial Data
H-Sync
V-Sync
1.
2.
3.
4.
5.
6.
7.
8.
Red
Green
Blue
Ground
Ground
R-Ground
G-Ground
B-Ground
9.
10.
11.
12.
13.
14.
15.
DDC-Serial Clock
24 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
2.
3.
TMDS Data 2-
TMDS Data 2+
TMDS Data 2/4
Shield
13.
14.
15.
TMDS Data 3+
+5V Power
Ground(for+5V)
4.
5.
6.
7.
TMDS Data 4-
TMDS Data 4+
DDC Clock
16.
17.
18.
19.
Hot Plug Detect
TMDS Data 0-
TMDS Data 0+
TMDS Data 0/5
Shield
TMDS Data 5-
TMDS Data 5+
TMDS Clock Shield
DDC Data
8.
9.
10.
11.
N.C.
20.
21.
22.
23.
TMDS Data 1-
TMDS Data 1+
TMDS Data 1/3
Shield
TMDS Clock +
TMDS Clock -
12.
TMDS Data 3-
24.
23
Pin
No.
Pin
No.
Signal Name
Pin No.
Signal Name
Signal Name
1
TMDS Data 2+
9
TMDS Data 0
17
DDC/CEC
Ground
2
3
TMDS Data 2
Shield
TMDS Data 2
10
11
TMDS Clock +
18
19
+5V Power
TMDS Clock
Shield
Hot Plug
Detect
TMDS Clock
4
5
TMDS Data 1+
12
13
TMDS Data
1Shield
CEC
TMDS Data 1
6
14
Reserved (N.C.
on device
7
8
TMDS Data 0+
15
16
SCL
TMDS Data 0
Shield
SDA
24
ꢀ
Product Registration and Technical Support
Register Your Planar Products Today
Thank you choosing Planar. To assure you receive all the benefits of your Planar
product and services, register your Planar product today.
Visit our website to register your productat
Cables, Replacement Lamps, Accessories
To find cables, replacement lamps and accessories for your Planar projector, LCD
monitor, touch screen or other Planar products visit our online store at
Technical Support
manuals, touch screen drivers, warranty information and access to Planar's
Technical Library for online troubleshooting.
To speak with Planar Customer Support please have you model and serial number
available and dial:
Planar Support
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US. Hours: 24
hours a day, 7 days a week.
Toll or long distance charges may apply.
25
|