Planet Technology Switch POE 151 User Manual

IEEE 802.3af  
Power over Ethernet Injector  
POE-151  
User’s Manual  
- 1 -  
 
TABLE OF CONTENTS  
1. INTRODUCTION.......................................................................................................................................... 4  
1.1 CHECKLIST ................................................................................................................................................ 4  
1.2 ABOUT THE POWER OVER ETHERNET INJECTOR .......................................................................................... 4  
1.3 FEATURES ................................................................................................................................................. 4  
1.4 SPECIFICATION .......................................................................................................................................... 5  
1.5 PRODUCT OUTLOOK................................................................................................................................... 5  
2. HARDWARE INSTALLATION..................................................................................................................... 6  
2.1 BEFORE INSTALLATION............................................................................................................................... 6  
2.2 POE-151, THE INJECTOR INSTALLATION...................................................................................................... 7  
2.3 POE-151 AND POE-151S, THE IEEE 802.3AF INJECTOR AND SPLITTER INSTALLATION................................ 7  
2.4 CONNECT WITH IEEE 802.3AF DEVICES...................................................................................................... 8  
3.TROUBLESHOOTING................................................................................................................................... 9  
APPENDIX A NETWORKING CONNECTION ............................................................................................... 10  
A.1 SWITCHS RJ-45 PIN ASSIGNMENTS......................................................................................................... 10  
A.2 RJ-45 CABLE PIN ASSIGNMENT................................................................................................................. 10  
- 3 -  
 
1. INTRODUCTION  
1.1 Checklist  
Thank you for purchasing our POE-151 IEEE 802.3af Power over Ethernet Injector, your Power over Ethernet  
Injector package shall contains following contents:  
Check the contents of your package for following parts:  
ò
ò
ò
ò
Power over Ethernet Injector x1  
User's manual CD x1  
Power Adapter x1  
Power cord x 1  
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton  
including the original packing material, and use them against to repack the product in case there is a need to return it to  
us for repair.  
1.2 About the Power over Ethernet Injector  
The POE-151 is an IEEE 802.3af Power over Ethernet Injector that provide DC 48V over Ethernet cables. The POE-151  
IEEE 802.3af Power over Ethernet Injector inserts DC Voltage into Cat.5 cable, allowing the cable between the Injector  
(POE-151) and Splitter (POE-151S-5V/9V/12V) to transfer data and power simultaneously. The maximum distance be-  
tween the Injector (POE-151) and Splitter (POE-151S-5V/9V/12V ) is 100 meters. With POE-151 installed, it is combines  
the Ethernet digital data with power over the twisted pair cables as an IEEE 802.3af Power over Ethernet Injector. And the  
IEEE 802.3af Power over Ethernet splitter shall separate the digital data and the power into two outputs.  
With IEEE 802.3af Power over Ethernet devices installed, the system administrator only have to use a single RJ-45  
Ethernet cable to carries both power and data to each devices. Besides, to connect through POE-151 and  
POE-151S-5V/9V/12V, you could also have following benefit that, cost saving, easy for networking planning and higher  
reliability. What’s more, upon any IEEE 802.3af devices installed, the POE-151 or POE-151S-5V/9V/12V all can make the  
connection while migrating or splitting the power and the Ethernet digital packets, such as connecting the POE-151 to an  
IEEE 802.3af complied devices, AP or IP phone.  
1.3 Features  
Comply with IEEE 802.3af Power over Ethernet, IEEE 802.3/802.3u 10/100Base-TX  
Provide DC 48V power over RJ-45 Ethernet cable to device with Ethernet port  
LED indicators power input indication  
Distance up to 100 meters  
Auto-detect of POE IEEE 802.3af equipment, protect devices from being damaged by incorrect installation  
Work with EIA568, category 5,4-pair cables for 10Base-T or 100Base-TX  
EMI standards comply with FCC, CE class B  
- 4 -  
 
1.4 Specification  
Model  
POE-151  
Ethernet Connector  
2 x RJ-45( 1 for data + DC in, 1 for Data out)  
Ethernet Data rate  
Input voltage  
10/100Mbps( vary on Ethernet device attached)  
DC 48V, 0.4A  
Number of device can be powered  
Ethernet cable  
1
TIA/EIA-568, Category 5/5e cable  
1 x power, 1 x POE ready / in-use  
73 x 55 x 24 mm  
LED indicator  
Dimension (W x D x H)  
EMI  
FCC Class B, CE mark  
Standard Compliance  
IEEE 802.3 Ethernet,  
IEEE 802.3u Fast Ethernet,  
IEEE 802.3af Power over Ethernet.  
1.5 Product Outlook  
LED definition:  
LED  
Color  
Yellow  
Green  
Function  
Power  
Lights to indicate that the POE-151 has power.  
PoE ready / in-use  
Lights to indicate the port is providing 48VDC in-line power.  
- 5 -  
 
2. HARDWARE INSTALLATION  
This product provides two different running speeds – 10Mbps, 100Mbps in the same device and automatically distin-  
guishes the speed of incoming connection.  
This section describes the hardware features of POE-151. Before connecting any network device to the POE-151, read  
this chapter carefully.  
2.1 Before Installation  
Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3af devices need  
to power on, the POE-151 can provide you a way to supply power for this Ethernet device conveniently and easily. The  
POE-151 equips with an AC-DC adapter with DC 48V input and injects this DC power into the pin of the twisted pair cable  
(pair 1, 2 and pair 3, 6 for Fast Ethernet).  
If there is very difficult to find a power socket for AC-DC Adapter of your non-IEEE 802.3af networked device, the POE-151  
and POE-151S can provide you a way to supply DC power for this Ethernet device conveniently and easily.  
The10/100Mbps speed duplex mode from Ethernet port of POE-151 depends on which Ethernet device attached.  
@Notice:  
The POE-151 and POE-151S can be installed in pair. However, the use of third-party device is allowed if the device  
complied with IEEE 802.3af standard.  
- 6 -  
 
2.2 POE-151, the Injector installation  
1. Connect a standard network cable from Switch/workstation to “Ethernet” port of POE-151.  
2. Connect the long cable that will be used to connect to the remote device to the port “Ethernet + DC”. The screen in  
Figure 1 appears.  
3. Connect the AC adapter to “DC 48V” of POE-151. The power LED will be steady on.  
Figure 1: the Injector installation  
2.3 POE-151 and POE-151S, the IEEE 802.3af Injector and Splitter installation  
1. Connect a standard network cable from “Ethernet+DC” of POE-151 to “Ethernet+DC” of POE-151S. The POE LED of  
POE-151 / POE-151S will light on continuance. The screen in Figure 2 appears.  
From POE-151 or  
IEEE 802.3af Power  
Supply equipment  
Figure 2: Connection to POE-150S  
2. Connect the UTP cable in the package from “Ethernet” of POE-151S to the RJ-45 port of remote device.  
3. Connect proper DC plug from “DC OUT” of POE-151S to remote device.  
4. Power on the remote device and the LED indicator on POE-151S will remains on, the screen in Figure 3 appears.  
- 7 -  
 
Figure 3: Connection architecture over POE-151/151S  
@Notice:  
1. According to IEEE 802.3af standard, the POE-151 will not inject power to the cable if not connecting to  
IEEE 802.3af devices.  
2. Please ensure the output voltage is correct before applying power to remote device.  
2.4 Connect with IEEE 802.3af devices  
Due to the capability of IEEE 802.3af standard, the POE-151 can directly connect with any IEEE 802.3af end-nodes like  
wireless access point, VoIP phones and Internet camera where support IEEE 802.3af In-line Power over Ethernet port.  
The screen in Figure 4 appears.  
Figure 4: Connection to IEEE 802.3af device  
Once POE-151 detects the existence of an IEEE 802.3af device, the LED indicator will be steady, ON to shows it is-  
providing power.  
@Notice:  
If the connected device is not fully complying with IEEE 802.3af standard or in-line power device, the LED in-  
dicator of POE-151 will not be steady on.  
- 8 -  
 
3.TROUBLESHOOTING  
This chapter contains information to help you solve problems. If the Switch is not functioning properly, make sure the  
Ethernet Switch was set up according to instructions in this manual.  
The PoE LED is not lit  
Solution:  
Check the cable connection between POE-151 and IEEE 802.3af device.  
Can the POE-151 work with Gigabit Ethernet device?  
Solution:  
The POE-151 use 4-wire for data transmission (pair 1, 2, pair 3, 6) and 4-wire for power supply (pair 4, 5, pair 7, 8),  
thus Gigabit Ethernet device connect to POE-151 will not send data over the power wire and the transmit speed shall  
change to 100Mbps.  
Why I connect my PoE device to POE-151 and it cannot power on?  
Solution:  
1. Please check the cable type of the connection from POE-151 to the other end. The cable should  
be an 8-wire UTP, Category 5 or above, EIA568 cable within 100 meters. A cable with only  
4-wire, short loop or over 100 meters, all will affect the power supply.  
2. Please check and assure the device that fully complied with IEEE 802.3af standard.  
- 9 -  
 
APPENDIX A NETWORKING CONNECTION  
A.1 Switch‘s RJ-45 Pin Assignments  
RJ-45 Connector pin assignment  
MDI  
MDI-X  
Contact  
Media Dependant In-  
terface  
Media Dependant In-  
terface -Cross  
1
2
TX + (transmit)  
TX - (transmit)  
Rx + (receive)  
Rx + (receive)  
Rx - (receive)  
TX + (transmit)  
3
4, 5  
6
DC current*  
Rx - (receive)  
TX - (transmit)  
7, 8  
Ground  
Remark:  
Gigabit Ethernet is not allowed to use POE-151 since pair 4,5 and pair 7, 8 are all being used for data transmission in  
Gigabit Ethernet data transmission. Only 10Base-T and 100Base-TX can apply with POE-151 products.  
A.2 RJ-45 cable pin assignment  
6
321  
6
321  
6
3
2 1  
The standard RJ-45 receptacle/connector  
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and  
color of straight cable and crossover cable connection:  
Figure A-1: Straight-Through and Crossover Cable  
Please make sure your connected cables are with same pin assignment and color as above picture before deploying the  
cables into your network.  
2080-A31120-000  
- 10 -  
 

Philips Baby Monitor 29PT8304NICAM User Manual
Philips Clock Radio AJ3142 User Manual
Philips Clock Radio AJ3226 User Manual
Philips Indoor Furnishings PL T57W User Manual
Philips Iron GC3331 User Manual
Pioneer Radio audio video multi channel receiver User Manual
Pioneer Stereo Receiver 516 S K User Manual
Powermate Portable Generator PM0464500 User Manual
Profoon Telecommunicatie Cordless Telephone PDX 1400 User Manual
Psion Teklogix Printer MLP 3040 Series User Manual