™
Polar CS200
User Manual
5.3 HEART RATE LIMITS SETTINGS (LIMITS SET)...........................................................................................................40
5.3.1 OwnZone.....................................................................................................................................................42
5.4 BICYCLE SETTINGS (BIKE SET)...............................................................................................................................45
5.5 WATCH SETTINGS (WATCH SET)..............................................................................................................................49
5.6 PERSONAL INFORMATION SETTINGS (USER SET) ....................................................................................................51
5.7 CYCLING COMPUTER SOUNDS AND UNITS SETTINGS (GENERAL SET) .....................................................................54
6. CONNECT - DATA COMMUNICATION.................................................................................................................................55
6.1 EDIT SETTINGS WITH A COMPUTER.........................................................................................................................55
6.2 TRANSFER YOUR TRAINING DATA TO THE TRAINING DIARY ON THE WEB ................................................................56
7. CARE AND MAINTENANCE................................................................................................................................................57
8. PRECAUTIONS.................................................................................................................................................................61
9. FREQUENTLY ASKED QUESTIONS.....................................................................................................................................63
10. TECHNICAL SPECIFICATIONS..........................................................................................................................................65
11. LIMITED POLAR INTERNATIONAL GUARANTEE .................................................................................................................67
12. POLAR DISCLAIMER ........................................................................................................................................................68
13. INDEX..............................................................................................................................................................................69
6
–
ENGLISH
1. INTRODUCTION TO THE POLAR CYCLING COMPUTER
Polar WearLink®+ transmitter
The connector transmits your
heart rate signal to the cycling
computer.
The electrode areas of the strap
detect your heart rate.
1.1 PRODUCT ELEMENTS
The Polar cycling computer package consists of the following parts:
Cycling Computer
The cycling computer displays and records
your cycling and exercise data during
exercise. Enter your personal settings into
the cycling computer and analyze exercise
information after workouts.
Polar Web Services
to support your training goals. Free registration gives you access
to a personalized training program, training diary, useful articles,
and much more. In addition, you can get the latest product tips and
support online at www.polar.fi.
Polar Bike Mount™
Secure the bike mount to your bike and
attach the cycling computer to it.
The latest version of this user manual can be downloaded at
Polar Speed Sensor™
A wireless speed sensor measures speed and
distance during cycling.
Polar Cadence Sensor™
CS200cad set includes a cadence sensor.
The wireless cadence sensor measures the
speed at which you turn the pedals of your
bicycle. The information relevant to using the
product with the cadence sensor is in a
blue text.
CS200 set does not include a cadence
sensor, but you can buy it as an accessory
product.
ENGLISH
–
7
1.2 USING YOUR CYCLING COMPUTER FOR THE FIRST TIME
Enter your settings in the Basic Settings mode (time, date, units, and personal settings).
How to enter Basic Settings
Entering accurate personal information ensures that you receive correct feedback based on your performance (calorie
consumption, OwnZone determination etc).
Activate the cycling computer by pressing the MIDDLE button.
The display fills with numbers and letters.
1. Press the MIDDLE button. BASIC SET is displayed.
2. Continue by pressing the MIDDLE button and follow the steps below:
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
3. Time Set
•
Time Mode 24h / 12h
RIGHT
MIDDLE
MIDDLE
• Set 24h or 12h format.
•
AM / PM (for 12h format)
RIGHT
• Set AM or PM.
8
–
ENGLISH
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
•
•
Hours
RIGHT
• Set the hours.*
MIDDLE
Minutes
RIGHT
• Set the minutes.*
MIDDLE
4. Date Set**
•
•
•
Day / Month
Month / Day
Year
RIGHT
MIDDLE
MIDDLE
MIDDLE
• Set the day (in 24h format) or
the month (in 12h format).*
RIGHT
• Set the month (in 24h format) or
the day (in 12h format).*
RIGHT
• Set the year.*
Note:
• *The numbers scroll faster if you press and hold the RIGHT button as you adjust the value.
• **The date will be displayed according to the time format selected (24h: day - month - year / 12h: month - day - year).
• After a change of battery or after you reset the cycling computer, you only need to set the time and date in the Basic Settings. You can
skip the rest of the settings by pressing and holding the LEFT button.
ENGLISH
–
9
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
5. Unit
kg/cm or lb/ft
RIGHT
MIDDLE
• Set the units for weight and height:
kg/cm or lb/ft.
6. Weight
kg/lb
RIGHT
MIDDLE
• Set your weight in kilograms or pounds.
Note: If you chose the wrong units, you can still
change them by pressing the LEFT button and
returning to step 5.
7. Height
cm/ft
RIGHT
MIDDLE
MIDDLE
MIDDLE
• Set your height in cm or ft.
• Set inches (if you chose lb/ft).
8. Birthday
RIGHT
•
Day / Month
• Set the day (in 24h format) or
the month (in 12h format).
•
Month / Day
RIGHT
MIDDLE
MIDDLE
• Set the month (in 24h format) or
the day (in 12h format).
•
Year
RIGHT
• Set the year.
10
–
ENGLISH
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
9. Sex
Male / Female
RIGHT
• Set male or female.
MIDDLE
• Settings done is displayed.
• To change your settings, press the LEFT button until you return to the desired setting.
• To accept the settings, press the MIDDLE button and the cycling computer goes to the Time mode.
The cycling computer goes to the power save mode (blank screen) by pressing the LEFT button or if you do not press any
button in the Time mode for five minutes. You can turn the cycling computer on again by pressing any button.
ENGLISH
–
11
1.3 INSTALLING THE BIKE MOUNT, CYCLING COMPUTER, SPEED AND CADENCE SENSORS
1.3.1 BIKE MOUNT AND CYCLING COMPUTER
1. You can install the bike mount and the cycling computer on the left or right side of the handlebar or on the stem with
cable ties.
4. Position the cycling computer on to the bike mount. Turn
the cycling computer clockwise until you hear a click.
You can release the cycling computer by pressing it
down and simultaneously turning it counter clockwise.
2. Place the rubber part on
the handlebar or stem and
insert the bike mount on
top of it.
2.
3. Pass the cable ties over the
bike mount and adjust
3.
them around the handlebar/
stem. Secure the bike mount
firmly. Cut off any excess
cable tie ends.
12
–
ENGLISH
1.3.2 SPEED SENSOR
To install the speed sensor and spoke magnet, you need cutters and a small screwdriver.
1. Attach the speed sensor
to the opposite side of the
front fork from the mounted
cycling computer.
2. Attach the rubber part to the
sensor.
1.
2.
The speed sensor and the
cycling computer should be
no more than 30-40 cm/
1’-1’3’’ apart.
3. Pass the cable ties through
the speed sensor and rubber
part holes.
3.
In case, the cycling computer is attached to the stem or if
you are exercising in surroundings with electromagnetic
interference, the distance should be minimized (minimum
30 cm/1’). The speed sensor and cycling computer should
form approximately a 90° angle.
4. Adjust the sensor to the front
fork so that the POLAR logo
faces outwards. Adjust the
ties loosely. Do not tighten
them fully yet.
4.
Should the distance between the cycling computer and the
speed sensor be longer than recommended (for example
on mountain bikes due to the front suspension), the speed
sensor could be attached on the same side of the front fork
as the cycling computer. In this case the maximum distance
is 50 cm/1´6”.
ENGLISH
–
13
5. Attach the magnet to a
spoke at the same level as
the sensor. The magnet hole
must be facing the speed
sensor. Fasten the magnet to
the spoke and tighten it
Your safety is important to us. While riding your bike,
please keep your eyes on the road to prevent any accidents
and injury. Check that you can turn the handlebar normally
and that the cable wires for brakes or gearing do not catch
on the bike mount or the sensors. Check also that the bike
mount or sensors does not hamper pedaling or the use of
brakes or gearing.
5.
max
4 mm /
0’16”
loosely with a screwdriver.
Do not tighten it fully yet.
Before you start cycling, you should set the wheel size of your
bicycle into the cycling computer. For further information
see pages 45-48.
Fine-tune the positioning of both the magnet and the speed
sensor so that the magnet passes close to the sensor but
does not touch it. Adjust the sensor towards the wheel/
spokes as much as possible. The gap between the sensor
and the magnet should be under 4 mm/0’16’’. The gap is
correct when you can fit a cable tie just about between the
magnet and the sensor.
Rotate the front tyre so that you can see a speed reading on
the display of your cycling computer. The reading indicates
that the magnet and the speed sensor are positioned
correctly. Once the magnet and the speed sensor are
positioned correctly, tighten the screw to the magnet with a
screwdriver. Also tighten the cable ties securely and cut off
any excess cable tie ends.
14
–
ENGLISH
1.3.3 CADENCE SENSOR
To install the cadence sensor and crank magnet, you need cutters.
1. Check the down tube to find
a suitable place for the
cadence sensor. The sensor
should be attached at a
maximum of 80 cm/ 2’6”
from the mounted cycling
computer. If needed the
sensor can also be attached
to the seat tube.
3. Clean and dry a suitable
place for the sensor and
adjust the sensor to the
down tube. If the sensor
touches the crank (when
rotating), change the sensor’s
1.
3.
max 80 cm /
2’6’’
position slightly upwards. Loosely adjust the cable ties. Do
not tighten them fully yet.
4. The crank magnet should be
installed vertically on the
inner side of the crank.
Before attaching the magnet
to the crank, the area should
be cleaned and dried
4.
2. Place the rubber part on to
the cadence sensor (A) and
pass the cable ties through
the cadence sensor and
rubber part holes (B).
2 A.
thoroughly. Attach the magnet to the crank and secure with
the tape.
2 B.
ENGLISH
–
15
5.
max 4 mm /
0’16’’
5. Fine-tune the positioning of both the crank magnet
and the sensor so that the magnet passes close
to the sensor without actually touching it.
Before you start cycling, you should set the wheel size of
your bicycle into the cycling computer and turn the cadence
function on. For further information see pages 45-48.
The maximum distance between the cadence sensor and
the crank magnet should be 4 mm/0’16”. The gap is correct
when you can fit a cable tie just about between the magnet
and the sensor. It is important that the lower corner of the
sensor must face the magnet when rotating, also when the
sensor has been attached to the seat tube. The lower corner
of the sensor is shown with an arrow in the picture. Once
the crank magnet and the sensor are positioned correctly,
tighten the cable ties securely and cut off any excess cable
tie ends.
16
–
ENGLISH
1.4 WEARING YOUR TRANSMITTER
Coded heart rate transmission reduces interference from other heart rate monitors that are close by. To make sure that the
code search is successful and to ensure trouble-free heart rate monitoring, keep the cycling computer within 1 meter/
3 feet of your transmitter. Check that you are not near other people with heart rate monitors or any source of electromagnetic
disturbance. For further information on interference, see Precautions on page 61.
To measure your heart rate, you need to wear the transmitter.
1.
1. Wet the electrode areas of the strap under running water.
2. Attach the connector to the strap. Adjust the strap to fit tightly but comfortably.
3. Tie the strap around your chest, just below the chest muscles, and attach the hook to
the other end of the strap.
2.
4. Check that the wet electrode areas are firmly against your skin and that the Polar logo
of the connector is in a central and upright position.
3.
Note: Detach the connector from the strap after every use, to maximize the transmitter
battery lifetime. Sweat and moisture may keep the electrodes wet and the transmitter
activated. This will reduce the transmitter battery life.
4.
See detailed washing instructions in Care and Maintenance chapter.
See the following chapter for how to start measuring your heart rate.
ENGLISH
–
17
2. EXERCISING
2.1 EXERCISE RECORDING AND HEART RATE MEASURING
You can record seven Exercise Files. There are two ways to start exercise recording. If you turn on the AutoStart function,
the cycling computer automatically starts and stops exercise recording when you start and stop cycling.
If the AutoStart function is off, you can start exercise recording by pressing the MIDDLE button. For further information
on AutoStart and how to set the function on/off, see pages 45-46.
1. Wear the transmitter as described in the section “Wearing your Transmitter” on page 17. Attach the bike mount, speed and
cadence sensors on your bicycle according to the instructions on pages 12-16.
2. Activate your blank cycling computer by pressing the MIDDLE button and start from the Time mode. The cycling computer
will automatically read your heart rate. Wait until the computer detects your heart rate and the framed, flashing heart
symbol
appears on the display in 15 seconds.* Exercise time is not recorded yet.
3. Set your cycling computer on the bike mount.
•
•
If you have turned AutoStart on, your heart rate value and speed appear on the display when you start cycling.
If you have turned AutoStart off, you can start exercise recording by pressing the MIDDLE button when your heart rate
value and speed appear on the display.
Your exercise time also starts running.
4. • If you have turned AutoStart on, the cycling computer automatically stops exercise recording when you stop cycling.
•
If AutoStart is off, you can stop the exercise by pressing the LEFT button twice. For further information on Stopping the
exercise, see page 25.
18
–
ENGLISH
• If your heart rate is not displayed and 00 appears on the display, the heart rate detection has stopped. Bring the cycling
computer near the Polar logo on the transmitter to restart the heart rate detection. No button press is needed.
• If OwnZone® is selected, the OwnZone determination procedure begins when exercise recording starts.
For further information, see the section OwnZone on page 42.
• To skip the OwnZone determination and use the previously determined OwnZone, press the MIDDLE button when OwnZone
symbol
appears on the display. If you have not determined your OwnZone before, your age-based heart rate
limits will be used.
Note: *
A frame around the heart rate symbol indicates a coded heart rate transmission.
•
If the cycling computer does not display your heart rate, make sure that the transmitter electrodes are moist and that the strap is
snug enough.
ENGLISH
–
19
2.2 FUNCTIONS DURING EXERCISE
Note: Your exercise information is saved only if the stopwatch, i.e. your exercise duration, has been running for more than one minute or at
least one lap has been stored.
Changing the display information: Press the RIGHT button to view the following options during exercise:
Ridden distance alternates with trip distance when you have taken at least one lap time.
1.
Trip distance is reset to zero each time you take a lap time by pressing the MIDDLE
button.
Riding speed (km/h or m/h)
Cadence, i.e., your pedaling speed
Heart rate. If there is no heart rate reading or you have not set your user information,
the speed is displayed instead.
Speed and heart rate are also displayed graphically. The more bars are displayed, the higher
your heart rate or speed and vice versa. One speed bar represents 5 km/h or 3 mph, and when all ten bars are displayed your
speed is 50 km/h or 30 mph or higher.
Note: You can also press and hold the RIGHT button to set the computer to browse the views automatically. Scrolling can be turned off by
pressing and holding the RIGHT button.
20
–
ENGLISH
2.
3.
4.
Average speed rise or drop indicator.
Cadence
Heart rate
The kilocalories you have burned so far.
The cumulation of kilocalories starts as your heart rate is displayed. If there is no heart rate
reading or you have not set your user information, the speed is displayed instead of calorie
information.
Stopwatch, i.e., exercise duration.
Cadence
Heart rate
The estimated time of arrival, or if the riding distance function is off, the speed is displayed
instead. If you set the distance you are going to ride, the cycling computer estimates your arrival
time to the destination according to your riding speed. For further information, see page 37.
Time of day
Cadence
Heart rate
ENGLISH
–
21
5.
Heart rate limits: On the left, you can see your lower heart rate limit and on the right your upper
heart rate limit. The heart rate symbol moves left or right according to your heart rate. If the
heart symbol is not visible, it means your heart rate is either below the flashing lower heart rate
limit or above the flashing upper heart rate limit. In this case an alarm goes on, provided the
sounds are turned on. If there is no heart rate reading, the limits are not displayed. For further
information, see page 40.
Time you have exercised in target zone, i.e., within the heart rate limits.
Cadence
Heart rate
6.
Average heart rate and average heart rate rise or drop indicator during last minute.
Current rate of kilocalories burned (kcal/h) alternates with your cycling intensity (kcal/km or
kcal/m). If there is no heart rate reading or you have not set your user information, the speed is
displayed instead of calorie information.
Cadence
Heart rate
22
–
ENGLISH
Target Zone Alarm: With the Target Zone Alarm you can make sure you exercise at the right intensity. When the target zone
heart rate limits are activated, the cycling computer sounds an alarm if you are above or below your heart rate limits. You
can set the limits for your target zone in the Settings/Limits SET menu. For further information, see page 40. If you are out of
your target zone, the heart rate value starts flashing and the cycling computer beeps with each heartbeat.
The symbol in the upper right corner of the display
indicates that the Target Zone Alarm sound is activated. Note that
the button sounds can also be set on/off in the Settings mode. To turning the sounds on or off, see page 54.
Note: When heart rate limits are not activated, no Target Zone Alarm in the exercise recording will sound, nor will target zone information be
placed in the Summary File or File.
Storing Lap and Split Time: Press the MIDDLE button to store lap and split time.
Lap time indicates elapsed time for one lap. Split time is elapsed time from the beginning of the exercise until storing a lap
time (for example from the beginning of the exercise until the 4th lap was stored).
Lap time
Split time
Number of the lap
Average heart rate calculated
from the beginning of the lap.
Note:
• If you have activated the Automatic Lap function in the Settings mode, your cycling computer automatically records laps when you reach
the set distance, e.g., every kilometer or mile. For further information, see page 37.
• You can store up to 50 lap times. When the lap memory is full, LapTime FULL text will be displayed. You can take lap times during your
exercise, but they are no longer recorded.
ENGLISH
–
23
Timers: The timers of your cycling computer work during your exercise recording. The cycling computer beeps and shows
when the timer time matches. If only timer 1 is on, the same timer beeps always after the set time has elapsed during your
exercise. If timer 2 is also on, the timers alternate during your exercise. For further information, see page 39.
Pausing Exercise:
1. Press the LEFT button. Exercise recording, stopwatch, and other calculations are paused.
2. To continue, press the MIDDLE button.
Exercising in the dark: If you activate the backlight by pressing and holding the MIDDLE button during an exercise
recording, the backlight will reactivate automatically during the same exercise every time you press any button.
Note: If the maximum file recording time (99 hours 59 min 59 s) is exceeded, the cycling computer beeps, pauses recording and displays
HALT. Stop recording by pressing the LEFT button. For further information on how to release memory for new files by deleting files, see page 31.
24
–
ENGLISH
2.3 STOPPING THE EXERCISE AND VIEWING SUMMARY FILE
1. Press the LEFT button to pause the exercise recording. Paused is displayed.
2. Press the LEFT button. Summary FILE is displayed and following information starts automatically scrolling:
Recorded Exercise File Information
Duration of recorded exercise.
Average heart rate.
Heart rate limits used during your exercise (if limits are set).
Time spent in target heart rate zone.
Kilocalories burnt during exercise.
Average speed.
Limits
In Zone
Kcal
AvgSpeed
Avg Cad.
Average cadence.
ENGLISH
–
25
Recorded Exercise File Information
Distance
RideTime
Ridden distance.
Time used for cycling.
E.g., if you stop cycling but do not stop the exercise recording the cycled time counting will automatically
stop, but the exercised time will continue to elapse.
If the AutoStart function is activated, the exercise and cycled time is the same, because the cycling computer
automatically starts and stops the recording as you start and stop cycling.
26
–
ENGLISH
3. VIEWING RECORDED INFORMATION - FILE
The Exercise File allows you to review cycling and exercise information collected while recording
an exercise session. The cycling computer starts recording information in a File as soon as
you start recording by pressing the MIDDLE button or using AutoStart function. Your exercise
information is saved only if the stopwatch has been on for more than one minute or at least one
lap has been stored.
3.1 VIEWING EXERCISE FILE
Press MIDDLE
• Date / Time
of the latest File
Press RIGHT
• Date / Time of the
previous Files
(scroll them by
pressing the RIGHT
button)
1. In the Time mode, press the RIGHT button. FILES is displayed.
2. Press the MIDDLE button. Date and Time alternate on the display.
3. The date and time when the exercise started
alternate on the display.
The most recently recorded file number is
displayed.
Use the RIGHT button to browse through the
files. The bigger the file number, the more
recent the file is.
Press RIGHT
• Delete Files
Note: Delete FILES is the last option in the Files loop. For further information on deleting Files, see page 31.
4. To view the information recorded in a file, press the MIDDLE button to select the file.
5. Use the RIGHT button to browse through the recorded information.
ENGLISH
–
27
Recorded Exercise File Information
Exe.Time
Duration of recorded exercise.
Avg HR / Max HR
The average heart rate and maximum heart rate alternate in heartbeats per minute (bpm).
Note: If you set heart rate limits in percentages of your maximum heart rate these values
are displayed also as percentages of your maximum heart rate (%).
Limits
The heart rate limits (in bpm or %) used during the exercise (if limits are set).
In/Above/Below
Zone
The exercise time that you have spent within (In Zone), above and below your target zone
limits (if limits are set) alternate on the display.
Kcal
Expended kilocalories during the exercise.
Ridden distance.
Distance
AvgSpeed
Max
Average and maximum speed.
Avg Cad.
Max
Average and maximum cadence.
Note:
• The alternating information switches automatically on the display. For quick scrolling, press the MIDDLE button.
• Press and hold the MIDDLE button to turn the backlight on in the File mode.
28
–
ENGLISH
Recorded Exercise File Information
RideTime
Time used for cycling.
LAPS
Number of laps while exercising.
Note: Lap information is displayed if you have stored at least one
lap during your exercise.
6. To view the best lap, press the MIDDLE button.
The best lap information is displayed:
The fastest lap time.
The number of the best lap.
7. Browse the laps with the RIGHT button. By pressing the MIDDLE
button you can browse the following lap information:
Split time.
Lap time.
The maximum heart rate and the average heart rate during the lap
alternate on the display.
Note: The last lap is automatically recorded when the exercise
has been stopped by pressing the LEFT button, but it is never the
best lap.
ENGLISH
–
29
Recorded Exercise File Information
Speed
The speed when you recorded the lap.
Average speed during the lap.
Cadence
The cadence when you recorded the lap.
Average cadence during the lap.
Distance
The Lap and
Split distances alternate on the display.
• To return to the Time mode, press and hold the LEFT button.
30
–
ENGLISH
3.2 DELETING FILES ONE BY ONE
You can release memory by deleting files. Once you have deleted a file, you cannot retrieve it.
1. In the Time mode, press the RIGHT button. FILES is displayed.
2. Press the MIDDLE button.
3. Use the RIGHT button until Delete FILES is displayed. Press the MIDDLE button.
4. Use the RIGHT button to browse the files.
5. Press the MIDDLE button to select the file to be deleted.
The cycling computer asks: Are You sure.
6. To delete the file, press the MIDDLE button.
Alternatively, to cancel the deletion, press the LEFT button.
You can continue browsing the files by pressing the RIGHT button.
• To continue deleting your files, go to step 4.
• To return to the Time mode, press and hold the LEFT button.
ENGLISH
–
31
4. TOTAL VALUES
Total values include cumulative and maximum values of information recorded during your
training sessions. The values are updated automatically when exercise recording is stopped.
Viewing the Total Values
1. In the Time mode, press the RIGHT button until TOTALS is displayed.
2. Press the MIDDLE button. Tot.Time and the total time are displayed.
3. Use the RIGHT button to browse through the following information:
Press MIDDLE
Total Values
The date when cumulation started.
• Tot.Time / Date
Press RIGHT
• Tot.Kcal/Date
Press RIGHT
Total cumulative exercise duration.
• Odometer / Date
Odometer1
Odometer2
(if in use)
Press RIGHT
• Distance1 / Date
Distance2
The date when cumulation started.
Total cumulative burned calories.
(if in use)
Press RIGHT
• MaxSpeed / Date
Press RIGHT
• Max.Cad / Date
Press RIGHT
• RideTime / Date
32
–
ENGLISH
Total Values
The date when cumulation started.
Odometer alternates with the date when cumulation started and the
cumulation for both bike 1 and bike 2.
Note: The odometer measures the cumulative ridden distance and it can
only be reset by using the UpLink. For further information, see page 55.
ENGLISH
–
33
Total Values
The date when cumulation started.
The ridden distance cumulation for bike 1 and bike 2 (Distance1
is updated when bike 1 is used and Distance2 is updated when
bike 2 is used).
The date when updated.
Maximum speed of the season.
34
–
ENGLISH
Total Values
The date when updated.
Maximum cadence of season.
The date when cumulation started.
Total cumulative ridden duration.
• To return to the Time mode, press and hold the LEFT button.
ENGLISH
–
35
Resetting Total Values or Returning the Previous Maximum Speed or Cadence Value
Use Total values as a seasonal counter of your exercise values by resetting them once a season. Instead of resetting, you can
return the previous maximum speed and cadence value. Once reset or returned, a value cannot be retrieved.
Start with any display in the previous table (Tot.Time, Tot.Kcal, Distance1/2, MaxSpeed, Max.Cad, RideTime).
1. Press the MIDDLE button to start resetting the desired value. Reset? is displayed.
2. Press the MIDDLE button. Are You Sure is displayed.
3. If sure, press the MIDDLE button.
Alternatively, to cancel the reset, press the LEFT button.
Returning the previous maximum speed and cadence values:
1. Start with the MaxSpeed or Max.Cad display.
2. Press the MIDDLE button. Reset? is displayed.
3. Press the RIGHT button. Return Old is displayed.
4. To return the previous value, press the MIDDLE button.
• To return to the Time mode, press and hold the LEFT button.
Note: The odometer can be reset only by using the UpLink. For further information, see page 55.
36
–
ENGLISH
5. SETTINGS
You can view or change the settings in the Settings menu.
Tip: Settings can also be configured using the Polar UpLink Tool™. They can then be transferred to your
cycling computer from your PC. For further information, see page 55.
To set values:
• Adjust or select a value with the RIGHT button.
• Accept your selection and proceed in the menu with the MIDDLE button.
• Cancel your selection or return to the previous mode or menu by pressing the LEFT button.
Press MIDDLE
• Cycling SET
Press RIGHT
• Timer SET
Press RIGHT
• Limits SET
Press RIGHT
• Bike SET
5.1 RIDING DISTANCE FOR ESTIMATED TIME OF ARRIVAL FUNCTION AND
AUTOMATIC LAP RECORDING SETTINGS (CYCLING SET)
In the cycling settings you can make two different settings:
Press RIGHT
• Watch SET
Press RIGHT
• User SET
Press RIGHT
• General SET
• RideDist: Setting riding distance.
Set the distance you are going to ride and the cycling computer will estimate your arrival time
to the destination according to your riding speed.
• A.Lap: Automatic lap recording.
Set the distance for the automatic lap and the cycling computer will record the lap
information every time you reach this distance. For example, if you set 1 km/m,
the cycling computer will record lap information every kilometer or mile.
ENGLISH
–
37
Both functions work during your exercise recording. For further information, see pages 20-23.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Continue by pressing the MIDDLE button and follow the steps below:
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
4. RideDist
On / OFF
RIGHT
MIDDLE
• Turn the riding distance function on or off.
(Skip step 5, if you turned the function off)
5. RideDist
On
RIGHT
MIDDLE
• Adjust the kilometers or miles.
6. A.Lap
On / OFF
RIGHT
MIDDLE
• Turn the automatic lap recording function on
or off.
(Skip step 7, if you turned the function off)
7. A.Lap
On
RIGHT
MIDDLE
• Adjust the kilometers or miles.
• To return to the Time mode, press and hold the LEFT button.
38
–
ENGLISH
5.2 TIMER SETTINGS (TIMER SET)
Your cycling computer is equipped with two alternating timers. The timers work during your exercise recording.
Tip: Use the timers for example as a reminder to drink at certain intervals or as a training tool in interval training, so that you know when
to switch from a harder to a lighter period and vice versa.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button. Timer SET is displayed.
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
5. Timer 1
On / OFF
RIGHT
MIDDLE
• Turn the Timer on or off.
(Skip step 6, if you turned the function off)
6. Timer 1
On
RIGHT
MIDDLE
MIDDLE
• Adjust the minutes (0-99 minutes).
RIGHT
• Adjust the seconds (0-59 seconds).
• To set timer 2, repeat steps 5 and 6.
• To return to the Time mode, press and hold the LEFT button.
ENGLISH
–
39
5.3 HEART RATE LIMITS SETTINGS (LIMITS SET)
In the heart rate limits settings (Limits SET) you can choose the heart rate limit type:
• Manual Limits:
You can create a target heart rate zone by setting the upper and the lower heart rate limits manually.
• OwnZone:
The cycling computer is able to determine your individual aerobic (cadiovascular) exercise heart rate
zone automatically. This is called OwnZone (OZ). OwnZone ensures that you exercise within safe
limits. For further information, see page 42.
• Limits Off:
You can also deactivate target zone limits, when there are no target heart rate limits during the
exercise recording, and no target heart rate zone values (In Zone) are calculated in the summary File
or File.
Use OwnZone or the target heart rate zone to maintain a particular level of intensity, depending on your objectives.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until Limits SET is displayed.
40
–
ENGLISH
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
5. TYPE
Manual / OwnZone / Off
RIGHT
MIDDLE
• Select Manual or OwnZone (automatic definition
of your personal heart rate zone) or Off.
(Skip steps 6-8, if you turned the function off)
6. HR / HR%
SET
RIGHT
MIDDLE
• Select heart rate displayed as beats per minute
(bpm) or as % of your maximum heart rate
(% HRmax).
(Skip steps 7-8, if you chose OwnZone)
7. HighLimit
RIGHT
MIDDLE
MIDDLE
• Adjust the upper heart rate limit.
8. LowLimit
RIGHT
• Adjust the lower heart rate limit.
• To return to the Time mode, press and hold the LEFT button.
ENGLISH
–
41
5.3.1 OWNZONE
The Polar cycling computer is able to determine your individual aerobic (cardiovascular) exercise heart rate zone
automatically. This is called OwnZone (OZ).
OwnZone is based on measuring changes in heart rate variability during your warm up. Heart rate variability reflects
changes in your physiology. For most adults OwnZone corresponds to 65-85 % of maximum heart rate. OwnZone can be
determined in 1-5 minutes during a warm-up period by cycling, walking or jogging. OwnZone may be easier to find during
indoor cycling than outdoor cycling because the speed is easier to control. The main idea is that you start exercising slowly
at a light intensity, i.e., heart rate lower than 100 bpm/50 % HRmax. You then gradually increase the intensity of your
exercise to raise your heart rate as smoothly as possible. Using OwnZone makes exercise easier and more enjoyable.
OwnZone has been developed for healthy people. Some health conditions may cause heart rate variability based OwnZone
determination to fail, for example high blood pressure, some cardiac arrhythmias, and some medications.
42
–
ENGLISH
Determining Your OwnZone Heart Rate Limits
Before you start to determine your OwnZone, make sure of the following:
• You have entered your user settings correctly. cycling computer will ask for missing information (for example date of
birth) before accepting limit settings.
• You have activated the OwnZone limits. With the OwnZone function on, the cycling computer will automatically determine
your OwnZone every time you start recording an exercise session.
You should redefine your OwnZone:
• when changing your exercise environment or exercise mode;
• if you are returning to exercise after a more than one week off;
• if you feel unusual about the physical state of your body when starting to exercise. For example you are stressed, not
recovered from the previous training or not feeling well;
• after changing your settings.
1. Start from the Time mode and press the MIDDLE button. The OwnZone symbol
appears on the display. If you
want to skip OwnZone determination and use the previously determined OwnZone, press the MIDDLE button.
2. OwnZone determination starts. Determination of your OwnZone happens in five stages.
Cycle or walk at a slow pace for 1 min. Keep your heart rate below 100 bpm/ 50 % HRmax during this first
stage. After each stage you will hear a beep (if the sound settings are on) and the display automatically
illuminates (if you have switched the backlight on once before), indicating the end of the stage.
Cycle or walk at a normal pace for 1 min. Slowly increase your heart rate by 10-20 bpm/ 5 % HRmax
Cycle or walk at a brisk pace for 1 min. Slowly increase your heart rate by 10-20 bpm/ 5 % HRmax
.
.
Cycle at a brisk pace or jog at a slow pace for 1 min. Slowly increase your heart rate by 10-20 bpm/ 5 % HRmax
Cycle or jog at a brisk pace or run for 1 min.
.
ENGLISH
–
43
3. At some point during the stages, you hear two beeps. Your OwnZone has been determined. If the determination was
successful, OwnZone and Updated alternate with the heart rate limits on the display. The limits are displayed as beats
per minute (bpm) or as a percentage of your maximum heart rate (%HRmax) depending on your settings.
4. If the determination was not successful, your previously determined OwnZone limits will be used and OwnZone appears
with the limits on the display. If you are determining your OwnZone for the first time, then the limits based on your age
will be used.
You can now continue with your exercise. Try to stay within the given heart rate zone to maximize exercise benefits.
For further information on OwnZone, see www.polar.fi.
44
–
ENGLISH
5.4 BICYCLE SETTINGS (BIKE SET)
You can set two bike preferences for the cycling computer. Prepare the settings for both bikes; when you start exercise
recording, just select bike 1 or 2. For both bikes you can prepare the following settings:
• AutoStart on/off The AutoStart function starts or stops automatically the exercise recording when you start or
stop cycling.
• Cadence on/off A wireless cadence sensor measures the speed at which you turn the pedals of your bicycle.
• Wheel
Wheel size settings are a prerequisite for cycling information.
For further information, see the following page.
1. In theTime mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until Bike SET is displayed.
ENGLISH
–
45
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
5. Bike 1 / 2
RIGHT
MIDDLE
• Select which bike settings you want to set:
bike 1 or 2.
6. AutoStart
On / OFF
RIGHT
MIDDLE
MIDDLE
MIDDLE
• Turn AutoStart function on or off.
7. Cadence
On / OFF
RIGHT
• Turn cadence function on or off.
8. Wheel
RIGHT
• Adjust the wheel size (mm) of your bicycle.
• To return to the Time mode, press and hold the LEFT button.
Note:
• The wheel size is always indicated in millimeters, as it is more accurate.
• The speed and distance measuring functions are always on.
46
–
ENGLISH
You have the following alternatives for finding out the wheel size of your bike:*
METHOD 1.
Look at the wheel of your bike and find the wheel diameter printed on it.
On the chart below, find your wheel diameter in inches or in ETRTO reading and match it to the wheel size in millimeters on
the right.
ETRTO
Wheel size diameter (inches)
Wheel size setting (mm)
25-559
23-571
35-559
37-559
47-559
20-622
52-559
23-622
25-622
28-622
32-622
42-622
47-622
26 x 1.0
1884
1909
1947
1958
2022
2051
2054
2070
2080
2101
2126
2189
2220
650 x 23C
26 x 1.50
700 x 35C
26 x 1.95
700 x 20C
26 x 2.0
700 x 23C
700 x 25C
700 x 28
700 x 32C
700 x 40C
700 x 47C
Note: *Wheel sizes on the above chart are advisory as wheel size depends on the wheel type and air pressure.
ENGLISH
–
47
METHOD 2.
Mark the tread of the front tire with a line and roll the tire perpendicular to the ground. You can also use the valve as a
mark. Mark a line on the ground. Move your bike on a flat surface straight ahead for one complete wheel rotation. Check that
the tire is perpendicular to the ground. Draw another line on the ground exactly where the mark on the front tire touches the
ground.
Measure the distance between the two lines on the ground.
mm
-4 mm
Subtract 4 mm to account for your weight on the bike to get your wheel circumference.
mm
This is the value you must set on the cycling computer.
48
–
ENGLISH
5.5 WATCH SETTINGS (WATCH SET)
In the Watch Set menu, you can change the time of day and date settings.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until Watch SET is displayed.
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
5. Time
•
Time Mode 24h/12h
RIGHT
MIDDLE
MIDDLE
MIDDLE
MIDDLE
• Set 24h or 12h time mode.
•
AM / PM
(if you use 12h format)
RIGHT
• Set AM or PM.
RIGHT
• Set the hours.
RIGHT
• Set the minutes.
ENGLISH
–
49
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
6. Date*
•
•
•
Day / Month
Month / Day
Year
RIGHT
MIDDLE
MIDDLE
MIDDLE
• Set the day (in 24h mode) or
the month (in 12h mode).
RIGHT
• Set the month (in 24h mode) or
the day (in 12h mode).
RIGHT
• Set the year.
• To return to the Time mode, press and hold the LEFT button.
Note: *The order in which you set date settings depends on which time mode you have chosen (24h: day - month - year /
12h: month - day - year).
50
–
ENGLISH
5.6 PERSONAL INFORMATION SETTINGS (USER SET)
Entering your personal information ensures that your calorie counter operates with the highest possible degree of accuracy.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until User SET is displayed.
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
5. Weight
kg/lb
RIGHT
MIDDLE
• Set your weight in kilograms or pounds.
6. Height
cm/ft
RIGHT
MIDDLE
MIDDLE
• Set your height in cm or ft.
• Set inches (if you chose lb/ft).
ENGLISH
–
51
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
7. Birthday
RIGHT
MIDDLE
•
•
•
Day / Month
Month / Day
Year
• Set the day (in 24h mode) or the month (in 12h mode).
RIGHT
• Set the month (in 24h mode) or the day (in 12h mode).
MIDDLE
RIGHT
• Set the year.
MIDDLE
MIDDLE
8. HR Max
RIGHT
• Adjust HRmax, if you know your laboratory measured
current maximum heart rate value. Your age-
predicted maximum heart rate value (220-age) is
displayed as a default setting when you set this value
for the first time.
9. HR Sit
RIGHT
MIDDLE
MIDDLE
• Adjust your heart rate value in a sitting position
(see the instructions on the next page).
10. Sex
RIGHT
•
Male / Female
• Set male or female.
• To return to the Time mode, press and hold the LEFT button.
52
–
ENGLISH
Maximum heart rate value (HRmax
)
HRmax is used to estimate energy expenditure. HRmax is the highest number of heartbeats per minute during maximum
physical exertion. HRmax is also useful when determining exercise intensity. The most accurate method for determining your
individual HRmax is to perform a maximal exercise stress test in a laboratory.
Heart rate value in a sitting position (HRsit)
HRsit is used to estimate energy expenditure. HRsit should be your typical heart rate when you are not doing any physical
activity (while sitting). To determine your HRsit easily, wear your transmitter, hold your cycling computer in your hand,
sit down and do not engage in any physical activity. After two or three minutes, press the MIDDLE button in the Time mode
to view your heart rate. This is your HRsit
.
To calculate your HRsit, more precisely, repeat the procedure several times and calculate your average.
ENGLISH
–
53
5.7 CYCLING COMPUTER SOUNDS AND UNITS SETTINGS (GENERAL SET)
You can view and change the following settings in the General Set:
• Sounds
• KeySound
• Units
Activity sounds for the cycling computer on or off
Button sounds for the cycling computer on or off.
The Unit settings affect the personal information and watch settings.
.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until General SET is displayed.
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads:
Press the RIGHT button to set the flashing value
Press the MIDDLE button to accept
the value
5. Sound
On / OFF
RIGHT
MIDDLE
MIDDLE
MIDDLE
• Turn activity sounds on or off.
6. KeySound
On / OFF
RIGHT
• Turn button sounds on or off.
7. kg/cm or lb/ft
RIGHT
Unit
• Select kg/cm or lb/ft units.
• To return to the Time mode, press and hold the LEFT button.
54
–
ENGLISH
6. CONNECT - DATA COMMUNICATION
6.1 EDIT SETTINGS WITH A COMPUTER
The Polar cycling computer offers you the option of editing your cycling computer settings with
the Polar UpLink Tool and your computer. You can also personalize the display of your cycling
computer by downloading logos. For this you need the Polar UpLink Tool.
You can download the Polar UpLink Tool at www.polar.fi.
In order to be able to use the Polar UpLink Tool, you need a computer with a sound card and
dynamic loudspeakers or headphones. For further information on system requirements, see the
Press MIDDLE
• Send FILES
Press RIGHT
• Receive DATA
To transfer files from your PC to your cycling computer:
1. In the Time mode press the RIGHT button until CONNECT is displayed.
2. Hold your cycling computer within 10 cm/ 4” from the loudspeakers or headphones. Press the
MIDDLE button. Send FILES is displayed.
3. Press the RIGHT button. Receive DATA
is displayed.
4. Start the data transfer from your PC.
5. If the data transfer was successful, Ok is displayed. If the transfer failes, Failed is
displayed.
ENGLISH
–
55
6.2 TRANSFER YOUR TRAINING DATA TO THE TRAINING DIARY ON THE WEB
polarpersonaltrainer.com is a complete Web service tailored to support your training goals. Free registration gives you ac-
cess to a personalized training program, diary, tests and calculators, useful articles, and much more. You can gain access
and start the registration process for the Web service at polarpersonaltrainer.com.
The Polar CS200™ and CS200cad™ Cycling Computers with the SonicLink data communication feature offers you the
option of transferring exercise files to your personal training diary on the polarpersonaltrainer.com Web service. For this you
need the Polar WebLink software.
You can download the Polar WebLink to your PC at polarpersonaltrainer.com.
In order to be able to transfer the recorded training information with Polar WebLink,
you need a personal computer with a sound card and microphone.
To transfer files from your cycling computer to the web service:
1. In the Time mode press the RIGHT button until CONNECT is displayed.
2. Hold your cycling computer about 5 cm/ 2” from the microphone. Press the MIDDLE button. Send FILES is displayed.
3. Press the MIDDLE button. Send ALL is displayed. You can choose to send either all files or one file at a time.
4. If you choose to send one file at a time, you can browse the files with the RIGHT button. Choose the file you want to sent
by pressing the MIDDLE button.
5. If you choose to send all files at a time, press the MIDDLE button when Send ALL is displayed.
6. If the data transfer is successful, Ok is displayed. If the transfer failes, Failed is displayed.
• To return to the Time mode, press and hold the LEFT button.
Note: See the help pages of the Polar WebLink software for further instructions.
56
–
ENGLISH
7. CARE AND MAINTENANCE
Keep your cycling computer, transmitter and sensors
in a cool and dry place. Do not keep them in a damp
environment, in non-breathable material (a plastic bag or
a sports bag) nor with conductive material (a wet towel).
The cycling computer, transmitter and sensors are water
resistant, and can be used in rainy weather. To maintain
the water resistance, do not wash the cycling computer
or the sensors with a pressure washer or sink them under
water. Do not expose to direct sunlight for extended periods
such as by leaving it in a car or mounted on the bike
mount.
Caring for Your Product
Like any electronic device, your Polar cycling computer
should be treated with care. The suggestions below will
help you to fulfill guarantee obligations and enjoy this
product for many years to come.
Detach the transmitter connector from the strap and
rinse the strap under running water after every use. Dry
the connector with a soft towel. Never use alcohol or any
abrasive material (steel wool or cleaning chemicals).
Wash the strap regularly in a washing machine at
40ºC/104ºF or at least after every fifth use. This ensures
reliable measurement and maximizes the life span of the
transmitter. Use a washing pouch. Do not soak, spin-dry,
iron, dry clean or bleach the strap. Do not use detergent
with bleach or fabric softener. Never put the transmitter
connector in the washing machine or dryer!
Keep your cycling computer clean. Clean the cycling
computer and sensors with a mild soap and water solution
and rinse them with clean water. Do not immerse them
in water. Dry them carefully with a soft towel. Never use
alcohol or any abrasive material such as steel wool or
cleaning chemicals.
Dry and store the strap and connector separately, to
maximize the transmitter battery lifetime. Wash the strap
in a washing machine before long-term storage and always
after use in pool water with high chlorine content.
Avoid hard hits to the cycling computer, speed and cadence
sensors, as these may damage the sensor units.
ENGLISH
–
57
replaced. Polar has designed speed and cadence sensors
to be sealed in order to maximize mechanical longevity
and reliability. The sensors have long-life batteries inside.
To purchase a new sensor contact your authorized Polar
Service Center or retailer.
Service
During the two-year guarantee/warranty period we
recommend that you service the product at an authorized
Polar Service Center only. The warranty does not cover
damage or consequential damage caused by service not
authorized by Polar Electro.
Note: In order to ensure the maximum lifespan of the battery cover,
open it only when you need to change the battery.
For contact information and all Polar Service Center
websites.
•
The low battery indicator and LowBatt. is displayed when
10-15% of the cycling computer battery capacity is left. The
backlight and cycling computer sounds are automatically
ensure we can keep improving our products and services to
better meet your needs.
deactivated when
Excessive use of the backlight drains the cycling computer’s
battery more rapidly.
In cold conditions the low battery indicator may appear, but the
indicator disappears when you return to warmer temperature.
is displayed.
•
•
Note: The username for your Polar Account is always your email
address. The same username and password are valid for Polar
product registration, polarpersonaltrainer.com, Polar discussion
forum and Newsletter registration.
Change Batteries Yourself
To change the batteries of the cycling computer and
Changing Batteries
transmitter yourself, carefully follow the instructions below.
The CS200 cycling computer and the WearLink+ transmitter
both have a user changeable battery. To change the battery
yourself, please follow the instructions carefully.
When changing the battery, make sure the sealing ring is
not damaged, in which case you should replace it with a
new one. You can purchase the sealing ring/battery kits at
The batteries for the speed and cadence sensors cannot be
58
–
ENGLISH
well-equipped Polar retailers and authorized Polar Services.
In the USA and Canada, the additional sealing rings are
available at authorized Polar Service Centers. In the USA
the sealing ring/battery kits are also available at www.
shoppolar.com.
Changing Cycling Computer Battery
1. Using a coin that sits tight into
1.
the back cover groove, open
the battery cover by pressing
slightly and unscrewing counter
clockwise.
Keep the batteries away from children. If swallowed,
contact a doctor immediately.
2. Remove the battery cover. The
battery is attached to the cover,
which should be carefully lifted
with a suitable sized small
rigid stick or bar, such as a
toothpick. A non-metal tool is
preferable. Remove the battery
and replace with a new one. Be
Batteries should be properly disposed of according to local
regulations.
2.
When handling a new, fully charged battery, avoid clasp-
like contact, i.e. simultaneous from both sides, with metal
or electrically conducting tools, like tweezers. This may
short-circuit the battery causing it to discharge more
rapidly. Typically, short circuiting does not damage the
battery, but it may decrease the capacity and lifetime of
the battery.
careful not to damage the threads of the back cover.
3. Place the negative (-) side of the battery against the
cycling computer and the positive (+) side against the
cover.
4. The sealing ring of the battery cover is also attached to
the cover. Only replace the sealing ring if it is damaged.
Before closing the battery cover, make sure that the
cover’s sealing ring is undamaged and it is placed
correctly in its groove.
Danger of explosion if the battery is replaced with wrong
type.
ENGLISH
–
59
5. Put the battery cover in its place and close it by
screwing the cover clockwise with a coin. Make sure that
the cover is closed properly!
WearLink+ Transmitter Battery
1. Using a coin, open the battery cover by
turning it counterclockwise to OPEN.
2. Insert the battery (CR2025) inside
the cover with the positive (+)
Note: After a battery change re-enter time and date settings in
Basic Settings. For further information, see page 8.
side against the cover. Make sure
the sealing ring is in the groove to ensure water
resistance.
3. Press the cover back into the connector.
4. Use the coin to turn the cover clockwise to CLOSE.
60
–
ENGLISH
8. PRECAUTIONS
The Polar cycling computer shows your performance
indicators. It indicates the level of physiological strain
and intensity during your exercise. It also measures speed
and distance when cycling with a Polar speed sensor. The
Polar cadence sensor is designed to measure cadence when
cycling. No other use is intended or implied.
• Do you have symptoms of any disease?
• Are you taking any blood pressure or heart medication?
• Do you have a history of breathing problems?
• Are you recovering from a serious illness or medical
treatment?
• Do you use a pacemaker or another implanted electronic
device?
• Do you smoke?
Electromagnetic Interference
Disturbances may occur near high voltage power lines,
traffic lights, overhead lines of electric railways, electric bus
lines or trams, televisions, car motors, bike computers, some
motor driven exercise equipment, cellular phones, or when
you walk through electric security gates.
• Are you pregnant?
In addition to exercise intensity, medications for heart con-
ditions, blood pressure, psychological conditions, asthma,
breathing, etc., as well as some energy drinks, alcohol, and
nicotine may also affect heart rate.
Minimizing Risks When Training
Training may include some risk. Before beginning a regular
training program, answer the following questions concerning
your health status. If you answer yes to any of these
questions, consult a physician before starting any training
program.
It is important to be sensitive to your body’s responses
during exercise. If you feel unexpected pain or excessive
fatigue when exercising, it is recommended that you stop
the exercise or continue at a lighter intensity.
• Have you been physically inactive for the past 5 years?
• Do you have high blood pressure or high blood choles-
terol?
Note! If you are using a pacemaker, you can use Polar
training computers. In theory interference to pacemaker
caused by Polar products should not be possible. In
ENGLISH
–
61
practice no reports exist to suggest anyone ever having ex-
perienced interference. We cannot however issue an official
guarantee on our products’ suitability with all pacemakers
or other implanted devices due to the variety of devices
available. If you have any doubts, or if you experience any
unusual sensations while using Polar products, please
consult your physician or contact the implanted electronic
device manufacturer to determine safety in your case.
Training equipment with electronic components may
cause interfering stray signals. To tackle these problems,
try the following:
1. Remove the transmitter from your chest and use the
training equipment as you would normally.
2. Move the wrist unit around until you find an area in
which it displays no stray reading or does not flash the
heart symbol. Interference is often worst right in front
of the display panel of the equipment, while the left or
right side of the display is relatively free of disturbance.
3. Put the transmitter back on your chest and keep the
wrist unit in this interference-free area as much as
possible.
If you are allergic to any substance that comes into
contact with your skin or if you suspect an allergic
reaction due to using the product, check the listed
materials on page 65. To avoid any skin reaction to the
transmitter, wear it over a shirt. However, moisten the shirt
well under the electrodes to ensure flawless operation.
If the CS200 still does not work, the piece of equip-
ment may be electrically too noisy for wireless heart rate
measurement.
Note: The combined impact of moisture and intense abrasion may
cause a black color to come off the transmitter’s surface, possibly
staining light-colored clothes. If you use insect repellent on your
skin, you must ensure that it does not come into contact with the
transmitter.
62
–
ENGLISH
9. FREQUENTLY ASKED QUESTIONS
What should I do if...
...there are no reactions to any buttons?
If there are no reactions to any buttons, reset the cycling computer.
Resetting only clears the date and time, not the recorded Files or
Totals. Reset the cycling computer by pressing and holding all
buttons until the display is filled with digits. By pressing any button
the unit goes to the Basic Settings mode (BASIC SET is displayed).
For further information, see page 8. If this does not work, have the
batteries checked.
...the display of the cycling computer is blank?
If you are using the cycling computer for the first time:
The cycling computer is in battery saving mode when it is
dispatched from the factory. To activate it, press the MIDDLE button
twice. The Basic Settings starts. For further information, see page 8.
If you have been using the cycling computer before:
The cycling computer goes to the power save mode (blank), if you
do not press any button in the Time mode for five minutes. You
can turn the cycling computer on again by pressing any button.
Alternatively the battery may be dead (see the next question for
further instructions).
Note: If you do not press any button after you reset the cycling
computer, within one minute the computer goes to the Time mode.
...the
Usually the first sign of an expiring battery is the low battery
indicator on the display. For further information, see page 58.
symbol is activated?
Note: Due to cold conditions the low battery indicator may appear,
but the indicator disappears when you return to a warmer
temperature.
...the battery of the cycling computer must be replaced?
We recommend having all service done by an authorized Polar
Service Center. This is especially necessary to ensure that the
guarantee remains valid and is not affected by incorrect repair
procedures performed by an unauthorized agent. Polar Service
will test your cycling computer for water resistance after battery
replacement and make a full periodic check of the complete cycling
computer set.
...another person with a cycling computer or a heart rate monitor
is causing interference?
Move away from that person and continue your exercise normally.
Alternatively, to avoid other person’s heart rate signals:
1. Take the transmitter off your chest for 30 seconds. Stay away
from the person with the other device.
2. Put the transmitter back on and bring the cycling computer up
to your chest near the transmitter’s Polar logo. The cycling
computer will start looking for a heart rate signal again.
Continue your exercise normally.
ENGLISH
–
63
...the cycling computer does not measure the calories?
In order to measure the calories you burn, you need to wear the
transmitter during recording.
...there is no heart rate reading (00)?
•
Check that the electrodes of the transmitter are moistened and
that you are wearing it as instructed.
•
•
Make sure the transmitter is clean.
...the heart rate, speed or distance reading becomes erratic or
extremely high?
Strong electromagnetic signals can cause erratic readings. So move
away from possible sources of disturbance such as high-voltage
power lines, traffic lights, electric railways or trams, car motors,
bike computers, some motor-driven exercise equipment (like fitness
testers) or cellular phones.
If the erratic heart rate reading continues after you have moved
away from the source of disturbance, slow down your speed and
check your pulse manually. If you feel it corresponds to the high
reading on the display, you may be experiencing cardiac arrhythmia.
Most cases of arrhythmia are not serious, but consult your doctor
nevertheless.
To avoid crosstalk from another cyclist with speed or cadence
sensors, keep a distance of at least one meter/ 3’4’’ between your
cycling computer and the speed or cadence sensors of the other
cyclist.
Check that you are not near high voltage power lines,
televisions, cellular phones, or other sources of electromagnetic
interference. Also make sure that you are not near (1 m/3 ft)
other heart rate monitor users, when starting your exercise
recording.
•
Cardiac arrhythmia may cause irregular readings or a cardiac
event may have altered your ECG waveform. In these cases,
consult your physician.
...there is no speed or cadence reading while cycling?
•
•
•
Check the correct positions and distances of the sensors with
the magnet and the cycling computer.
Check that you have set the correct cycling settings in your
cycling computer. For further information, see page 45.
If the 00 reading appears irregularly, this may be due to
temporary electromagnetic interference in your current
surroundings.
•
If the 00 reading is constant, you may have exceeded
4500 (speed sensor)/ 3500 (cadence sensor) riding hours and
the battery is empty.
64
–
ENGLISH
10. TECHNICAL SPECIFICATIONS
Cycling computer
Material:
Thermoplastic polymer case
better than 0.5 seconds per day at
25 °C/ 77 °F temperature.
1% or 1 bpm, whichever larger,
the definition applies to steady state
conditions. Heart rate is displayed as
number of heartbeats per minute (bpm)
or as % of your maximum heart rate.
Speed and cadence sensors
Speed sensor battery life: Average 4500 hours of use
Cadence sensor battery life: Average 3500 hours of use
Watch accuracy:
Heart rate accuracy:
Accuracy:
Material:
Operating temperature:
1 %
Thermoplastic polymer case
-10 °C to +50 °C / +14 °F to +122 °F
SYSTEM REQUIREMENTS
Heart rate measuring range: 15-240
Maximum time recorded
to File:
Limit values of information
recorded to exercise file:
Current speed display range: 0-127 km/h or 0-75 mph
Polar WebLink using SonicLink™ data communication
• PC
• Microsoft Windows XP/Vista/7
• Sound card
• Microphone
99 h 59 min 59 s
7 exercise files
Cadence display range:
Operating temperature:
Battery life:
25-199 rpm
Polar UpLink Tool
• PC
• Microsoft Windows XP/Vista/7
• Sound card
• Dynamic loudspeakers or headphones
-10 °C to +50 °C / +14 °F to +122 °F
Average 2 years in normal use
(1 h/day, 7 days/week)
CR 2032
Battery type:
Battery sealing ring:
OR 23.6 x 1.0 (silicon rubber)
The Polar CS200 cycling computer applies the following patented
technologies, among others:
Transmitter
Battery type:
CR 2025
• OwnZone® assessment for determining personal target heart rate
limits for the day
Battery sealing ring:
Battery life:
Operating temperature:
Connector material:
Strap material:
O-ring 20.0 x 1.0 Material FPM
Average 700 hours of use
-10 °C to +50 °C / 14 °F to 122 °F
Polyamide
Polyurethane, polyamide, nylon,
polyester and elasthane
• OwnCode® coded transmission
• WearLink® technology for heart rate measurement
ENGLISH
–
65
Water resistance of Polar products is tested according to International Standard ISO 2281. Products are divided into three different categories
according to their water resistance. Check the back of your Polar product for the water resistance category and compare it to the chart below.
Please note that these definitions do not necessarily apply to products of other manufacturers.
Marking on the
case back
Wash splashes, sweat, Bathing and
SCUBA diving
Water resistant
Skin diving with
snorkel (no air tanks)
raindrops etc.
swimming
(with air tanks) characteristics
Water resistant
X
Splashes, raindrops etc.
Water resistant
30m / 50m
X
X
X
X
Minimum for bathing
and swimming
Water resistant 100m
For frequent use in water
but no SCUBA diving
X
66
–
ENGLISH
11. LIMITED POLAR INTERNATIONAL GUARANTEE
• This guarantee does not affect the consumer’s statutory rights under applicable national or state laws in force, or the consumer’s rights
against the dealer arising from their sales/purchase contract.
• This limited Polar international guarantee is issued by Polar Electro Inc. for consumers who have purchased this product in the USA or
Canada. This limited Polar international guarantee is issued by Polar Electro Oy for consumers who have purchased this product in other
countries.
• Polar Electro Oy/Polar Electro Inc. guarantees the original consumer/purchaser of this device that the product will be free from defects in
material or workmanship for two (2) years from the date of purchase.
• The receipt of the original purchase is your proof of purchase!
• The guarantee does not cover the battery, normal wear and tear, damage due to misuse, abuse, accidents or non-compliance with the
precautions; improper maintenance, commercial use, cracked, broken or scratched cases/displays, elastic strap and Polar apparel.
• The guarantee does not cover any damage/s, losses, costs or expenses, direct, indirect or incidental, consequential or special, arising out of,
or related to the product.
• Items purchased second hand are not covered by the two (2) year warranty, unless otherwise stipulated by local law.
• During the guarantee period, the product will be either repaired or replaced at any of the authorized Polar Service Centers regardless of the
country of purchase.
Guarantee with respect to any product will be limited to countries where the product has been initially marketed.
This product is compliant with Directive 93/42/EEC.
0537
This crossed out wheeled bin marking shows that Polar products are electronic devices and are in the scope of Directive 2002/96/EC
of the European Parliament and of the Council on waste electrical and electronic equipment (WEEE) and batteries and accumula-
tors used in products are in the scope of Directive 2006/66/EC of the European Parliament and of the Council of 6 September 2006
on batteries and accumulators and waste batteries and accumulators. These products and batteries/accumulators inside Polar
products should thus be disposed of separately in EU countries.
This marking shows that the product is protected against electric shocks.
ENGLISH
–
67
12. POLAR DISCLAIMER
•
•
•
The material in this manual is for informational purposes only. The products it describes are subject to change without prior notice,
due to the manufacturer’s continuous development program.
Polar Electro Inc./Polar Electro Oy makes no representations or warranties with respect to this manual or with respect to the products
described herein.
Polar Electro Inc./Polar Electro Oy shall not be liable for any damages, losses, costs or expenses, direct, indirect or incidental,
consequential or special, arising out of, or related to the use of this material of the products described herein.
This product is protected by one or several of the following patents:
FI68734, DE3439238, GB2149514, HK812/1989, US4625733, FI88223, DE4215549, FR92.06120, GB2257523, HK113/1996, SG9591671-4,
US5491474, FI88972, FR92.09150, GB2258587, HK306/1996, SG9592117-7, US5486818, FI96380, US5611346, EP665947, DE69414362,
FI4150, DE20008882.3, US6477397, FR0006504, FI4069, DE29910633, GB2339833, US6272365, FI107776, US6327486, FI110915,
US6537227, US6277080, FI111514, GB2326240, US6361502, US6418394, US6229454, EP836165, FI100924, WO96/20640, US6104947,
US5719825, US5848027, EP1055158, US6714812, FI88972, FR92.09150, GB2258587, HK306/1996, SG9592117-7, US5486818.
Other patents pending.
Polar Electro Oy is a ISO 9001:2008 certified company. Copyright © 2005–2012 Polar Electro Oy, FI-90440 KEMPELE, Finland.
All rights reserved. No part of this manual may be used or reproduced in any form or by any means without prior written permission of
Polar Electro Oy. The names and logos in this user manual or in the package of this product are trademarks of Polar Electro Oy. The names and
logos marked with a ® symbol in this user manual or in the package of this product are registered trademarks of Polar Electro Oy. Windows is
a registered trademark of Microsoft Corporation and Mac OS is a registered trademark of Apple Inc.
Manufactured by:
Polar Electro Oy, Professorintie 5, FI-90440 KEMPELE
Tel +358 8 5202 100, Fax +358 8 5202 300
www.polar.fi
68
–
ENGLISH
13. INDEX
24h/12h time mode.............................................................9
Automatic Lap...................................................................23
AutoStart...........................................................................18
Backlight...........................................................................24
Battery replacement.................................................... 58-60
Bike settings.....................................................................45
Cadence sensor.............................................................7, 15
Date settings............................................................... 49-50
File....................................................................................27
Halt...................................................................................24
Timers...............................................................................39
Total Values ......................................................................32
Transmitter .......................................................................17
Unit setting.......................................................................54
UpLink Tool........................................................................55
User settings.....................................................................51
WebLink Tool .....................................................................56
Heart rate
............................................................. 18-19
Heart rate limits................................................................40
HRsit ..................................................................................53
LapTime ful.......................................................................23
Low battery indication
................................................58
Recording an exercise .......................................................18
Reset the cycling computer...............................................63
Settings.............................................................................37
Sounds..............................................................................23
Speed sensor.................................................................7, 13
Start measuring your heart rate........................................18
Stopwatch.........................................................................20
Target Zone Alarm
......................................................23
17946426.00 EMANUAL CS200 ENG
ENGLISH
–
69
Manufactured by
Polar Electro Oy
Professorintie 5
FIN-90440 KEMPELE
Tel +358 8 5202 100
Fax +358 8 5202 300
www.polar.fi
|