Installation Quickstart
f
Adapter for 120 film, 2 1/4 x 2 1/4 in.
Adapter for single 35mm slide
1 Unpack the Box
Make sure you have all the following components. Contact your
dealer if any is missing or damaged.
g
h
i
Adapter for 120 film, 2 1/4 x 2 3/4 in.
Four-slide film carrier
a
b
c
d
j
35mm slide spacer (not shown)
k
l
Two magnets for 120 film (not shown)
The PolaColor Insight Software CD (not shown) containing:
•
•
PolaColor Insight software for Windows 95, 98, and NT
PolaColor Insight software for Power MAC and
PowerPC systems and an Adobe Photoshop plug-in
•
Online user’s guide
Warning: Nothing inside the scanner is user serviceable.
Do not disassemble the scanner. Doing so could result
in severe electrical shock and damage to the scanner.
This action may also void your warranty. Contact
Polaroid Technical Support or your dealer if the
scanner is malfunctioning. (To contact Polaroid from
within the U.S.A., call 1-800-432-5355. Outside the
U.S.A., see Getting assistance in the online user’s
Wide Web.)
e
f
g
h
i
a
b
c
Scanner
Power cable (several provided for various power sources)
This manual
d
e
SCSI cable (25-pin to 50-pin)
Film carrier for 4x5 film
English
4
English
5
2 Position the Scanner
3 Install the Software
Place the scanner on a flat, stable surface, free of vibration. Leave
at least 2 inches (50mm) of space around all sides and the top of
the scanner for adequate ventilation, and leave room at the back
to reach the power switch on the rear panel.
1
2
3
Turn the computer on.
Close any applications that may be running.
Insert the Polaroid PolaColor Insight CD into the drive.
Power Mac or PowerPC
Windows 95, 98 or NT
Caution: As with any highly sensitive optical equipment, vibra-
tions or bumping the scanner during use may result in
picture defects. Locate the unit where it will not be dis-
turbed during use.
1 Select Polaroid
PolaColor Insight
Installer.
1 Wait for the install
program to start.
If it does not, select
Run from the Start
menu. Click Browse
and select
SETUP.EXE on the
CD-ROM. Click OK.
2 Follow the instruc-
tions on the screen.
3 If you want to install
the Photoshop plug-in,
double-click the Plug
In Installer in the
PolaColor Insight
folder and follow the
instructions on the
screen.
2 Follow the instruc-
tions on the screen.
4
Remove the CD from the drive.
Power Mac or PowerPC
Windows 95, 98 or NT
4 Connect the Scanner to
the Computer
The SprintScan 45 Ultra requires a SCSI host adapter in your
computer. If your computer does not have an adapter, you must
install one (see page 17). If your computer is a PC-compatible
with a SCSI adapter, but the adapter is connected to a hard drive
or CD-ROM drive, installing a second adapter is recommended.
1 Run the Apple System
Profiler program, usually
on the Apple menu. If not,
it may be available from
Look at the address switch
on each SCSI device
connected to your system. If
necessary, see the
instructions provided with
the devices.
swupdates.
2 Click Devices and
Volumes to view the SCSI
device addresses.
Set the Scanner SCSI Address
Each device connected to a SCSI host adapter must have a unique
address from 0-6. To assure a unique address for the scanner,
determine the addresses of any other SCSI devices.
Make sure the scanner is turned off and set the address switch
(b on page 7) to a value not used by any other device.
Note: The address is preset to 4. Do not change it unless another
device is using 4. Other addresses typically available are 2,
5, and 6.
English
6
English
7
Connect the SCSI Cables
a
Place the scanner at the end of the SCSI chain or between the
computer and other SCSI devices as shown in the following
diagrams. Use the shortest possible cables.
Note: Turn the computer, scanner and all other SCSI devices off
before connecting or disconnecting any cables. Do not
connect the scanner to the parallel connector on your
computer. Doing so could damage the scanner or
computer.
50 pins
25 pins
b
c
d
e
a
b
c
SCSI address switch
Power switch
d
e
SCSI termination switch
SCSI connectors (25, 50)
Power connector
Computer
Scanner
(termination on)
You may need additional cables or adapters to connect the
scanner. Your cable must have a 50-pin Centronics M or DB-25
M connector at one end for attachment to the scanner, and the
cable should be as short as possible. To determine the connector
you need for attachment to your SCSI adapter, refer to
instructions with the adapter.
25
pins
50
pins
25
pins
50
pins
SetTermination
Computer
Other SCSI device
(unterminated)
Scanner
(termination on)
Terminate the scanner and all other SCSI devices as shown in the
appropriate cabling diagram to the left or on page 7. The last
device in the SCSI chain must be terminated (or termination on),
while all other devices must be unterminated (or termination off).
25
pins
50
25
50
pins
pins
pins
Set scanner termination with the termination switch (d on
page 7). On = terminated, Off = unterminated.
Termination instructions for your other SCSI devices are
provided with the devices.
Computer
Scanner
(termination off)
Other SCSI device
(terminated)
English
8
English
9
2
Turn the scanner power switch on.
5 Connect the Scanner to
AC Power andTurn On
1
Connect the power cord to the power connector (b).
3
Check the lights. The green light indicates power on. The
yellow light blinks while the scanner initializes, and it
remains steady when the scanner is ready. (The yellow light
also blinks during scanning.)
4
5
Turn the computer on.
Wait for the system to install the scanner driver and display
the normal desktop.
a
b
a
Power switch
b
Power connector
6 Loading the Film Carriers
The Four-Slide Film Carrier
1
With the text facing up and the hinge at the top, open the
carrier flat as shown.
3
Close the carrier carefully.
The 4x5 Carrier (for 4x5 film)
1
To unlock the carrier, squeeze the two halves of the carrier
together at the bottom edge (near the locking knob) with one
hand while turning the locking knob in either direction, until
the slot in the knob points to UNLOCK.
2
Place up to four mounted 35mm slides in the spaces pro-
vided. Be sure the slide mounts fit properly in the recessed
areas. The images should be right-side up and right-reading
as you do so. The emulsion side will face down.
English 10
English 11
2
Open the carrier flat. Insert a 4x5 chrome or negative so that
the left edge is against the positioning pins. Position the film
so the image is right-reading and right-side up (emulsion-
side down).
The 120 Film Adapters
(for 2 1/4 x 21/4 and 2 1/4 x 2 3/4 in. film)
1
2
Open the 4x5 carrier as described previously.
Locate the appropriate adapter for your image. One is
designed for 2 1/4 x 2 3/4 in. images, and one is for 2 1/4 x
2π in. square images.
Note: The emulsion side is the dull side.
Note: The frame of film must be cut from the film strip in
order to be scanned.
3
Orient the adapter so that the words THIS SIDE UP (on the
adapter) face up, and the notches are at the left edge. Place
the unmounted film over the opening, within the raised
ridges of the adapter. Position the film so the image is right-
reading and right-side up.
Pins
3
3
Close the carrier. Squeeze the carrier at the bottom edge and
turn the knob to lock it.
4
5
6
Secure the film with the two magnets provided, on the top
and bottom edges. Be sure the magnets are also within the
raised ridges.
The Single-35mm Carrier
1
2
Open the 4x5 carrier as described previously.
Locate the single-35mm adapter.
Place the adapter in the 4x5 carrier, sliding the notches into
the pins on the left edge. The film and magnets should be
face up, as shown.
Note: You can use a negative, or a mounted or unmounted
slide.
3
Orient the adapter so the metal tabs face up, and the notches
are at the left edge. Slide the film into the channel, under the
two metal tabs. Position the film so the image is right-
reading and right-side up.
Close the carrier. Squeeze the carrier at the bottom edge and
turn the knob to lock it.
English 12
English 13
4
If the film is unmounted or the mount is thin, use the slide
spacer provided. Position the slide spacer on top of the slide.
The film should fit snugly into the adapter. (The spacer also
ensures that the image will be at the correct distance from the
scanning mechanism.)
6
Close the carrier. Squeeze the carrier at the bottom edge and
turn the knob to lock it.
5
Place the adapter in the 4x5 carrier, sliding the notches into
the pins on the left edge. The slide and tabs should be facing
up.
3
4
Close the carrier access door. The scanner will not scan if the
door is open.
7 Insert the Carrier into the
Scanner
Note: Do not open the carrier access door while a scan is in
process; the scan will be interrupted. The scan will
resume when the door is closed, but the quality of the
scan may be reduced. Scan again with the door
closed for best scanning quality.
1
Open the carrier access door.
Initiate the scan from your software. The software will
prompt you when the scan is finished.
2
Insert the carrier gently and firmly into the carrier slot as
shown, until you feel it stop.
English 14
English 15
4
Select the type of slide or negative you are scanning from the
Input list on the Preview panel.
8 Preview an Image
1
Load the film or slide into the film carrier (as described
previously).
5
6
Select your monitor type from the Display list.
Type or select the number of the carrier frame you want to
scan in the Frame Number box.
2
3
Insert the carrier into the scanner (as described previously).
Start the PolaColor Insight program:
7
Click Preview.
The image appears on the Preview panel.
Power Mac or PowerPC
Windows 95, 98 or NT
Double-click PolaColor
Insight.
1 Select Programs from
the Start menu.
2 Point to Polaroid Pola-
Color Insight, then
select PolaColor
Insight.
To start the Photoshop
plug-in within another
application, select Import
from the application’s
File menu and select
PolaColor Insight.
9 Enhance and Scan the
Image
Follow the online user’s guide instructions to enhance the image
and perform a final scan.
10 Remove the Carrier
1
When the scan is complete, open the door and remove the
carrier. Remove the film and store it properly to protect it
from dust and fingerprints.
2
Close the carrier access door. The door should be kept closed
at all times to protect the mechanism from dust.
To view the online PolaColor Insight User’s Guide:
Power Mac or PowerPC
Windows 95, 98 or NT
1 Double-click PolaColor
Insight, launching the
PolaColor Insight
program.
1 Select Programs from
the Windows Start
menu.
2 Point to Polaroid Pola-
Color Insight and select
User's Guide.
2 Select PolaColor Insight
Help from the Help
menu.
English 16
English 17
Installing a SCSI Host Adapter LimitedWarranty
The SprintScan 45 Ultra connects to a SCSI host adapter in your
computer. Most Macintosh computers have a SCSI adapter built
in, but most IBM PC compatible computers do not.
Polaroid Corporation warrants the SprintScan 45 Ultra scanner
against defects in manufacture or workmanship for a period of
one year from the date of purchase. To verify the warranty period,
you should keep the invoice, sales receipt, or other proof of the
purchase date.
If you must install a SCSI adapter, turn the computer off and
follow instructions provided by the adapter manufacturer. (The
procedure usually includes software installation. If your PC uses
the Windows NT operating system, log in as an administrator
before installation.)
Should this product or any component or accessory included with
it, with the exception of software, prove to be defective at any
time during the warranty period, Polaroid Corporation will, at its
discretion, either replace or repair this item, without charge.
This warranty does not cover damage caused by accident,
incorrect installation, unauthorized modification, and misuse or
abuse. A charge will be made for repair of such damage.
This warranty excludes all consequential damages. Some
jurisdictions do not allow the exclusion or limitation of
consequential damages, so the foregoing exclusion may not
apply to you.
•
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Radio andTelevision
Interference
Consult the dealer or an experienced radio/TV technician for
help.
FCC Notice (U.S.A.)
Note: A shielded interface cable with a ferrite core installed on
the scanner connector end must be used with this
equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
FCC Caution: To assure continued compliance, any changes or
modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Product: The Polaroid SprintScan 45 Ultra Scanner
Marketed by: Polaroid Corporation, Cambridge, MA 02139
U.S.A. Telephone: 1-800-432-5355
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two considerations: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
•
•
Reorient/relocate the receiving antenna.
© 2000 Polaroid Corporation, Cambridge, MA 02139, U.S.A. All rights reserved.
Increase the separation between the equipment and receiver.
“Polaroid”, “SprintScan”, and “PolaColor” are trademarks of Polaroid
Corporation. All other product names may be trademarks of their respective
owners. 111705B (PW–91396M-1)
English 18
Installation Quickstart Errata
SprintScan 45 Ultra
Installation Quickstart Errata
English . . . . . . . . . . . . . . . . . . . . . . . . . 3
English
3
PC Systems
About This Document
• An IBM PC or compatible with a 300-MHz Pentium processor
and 128 megabytes (MB) of RAM (RAM equal to twice the
typical image file size recommended).
This document provides corrections and updates for SprintScan
45 Ultra Installation Quickstart packaged with the scanner.
• Microsoft Windows 95, 98, 2000, Me or NT (version 4 or
later) operating system.
System Requirements (Page 3)
Macintosh Systems
• 400 MB of free disk space.
• A Power Macintosh computer (includes Power Macintosh G3
and G4 computers) or compatible with a PowerPC processor,
and 64 megabytes (MB) of RAM.
• An ASPI-compliant SCSI adapter with the appropriate
Windows drivers.
• A video adapter and monitor capable of displaying 24-bit color
(16.7 million colors) is recommended for optimal display of
scanned pictures.
• A SCSI port.
• 400 MB of free disk space.
• Scratch disk space equal to twice the final image file size plus
4 MB.
Note: PolaColor Insight software runs on systems with video
adapters and monitors with less color capability, but pictures
displayed on the monitor may not be satisfactory.
• Apple system software version 7.6 or later.
• A video adapter and monitor capable of displaying thousands
of colors, minimum. 24-bit color (16. 7 million colors) is
recommended for optimal display of scanned pictures.
Note: PolaColor Insight software runs on systems with video
adapters and monitors with less color capability, but pictures
displayed on the monitor may not be satisfactory.
1 Unpack the Box (Page 4)
SCSI Termination Switch (Page 7)
The normal SCSI termination switch positions (d in the drawing
on page 7) are up = on (terminated) and down = off
(unterminated).
The PolaColor Insight Software CD contains the following:
• PolaColor Insight software for Windows 95, 98, Me, 2000 and
NT
Scanners with serial numbers starting with the following
characters, however, have the opposite configuration (up = off,
down = on): D0, E0, F0, G0, H0. The serial number is on the
bottom of the scanner.
• PolaColor Insight software for Power MAC and PowerPC
systems
• Online user's guide
3 Install the Software (Page 5)
The Four-Slide Film Carrier
(Page 10)
Step 3 for Power Mac or PowerPC (plug in installation) is no
longer necessary. The Photoshop plug in for PolaColor Insight
installs automatically during normal installation.
The four-slide film carrier is compatible with thin plastic- and
paper-mount 35mm slides. If you must force the carrier closed,
however, do not use it. Instead, use the single 35mm adapter with
the 4x5 carrier (page 12).
4 Connect the Scanner to the
Computer (Page 6)
The SprintScan 45 Ultra scanner SCSI address is set to 6 at the
factory. Do not change it unless another device is using that
address. Do not use address switch setting 7, 8 or 9.
Glass-mount 35mm slides cannot be scanned with the four-slide
film carrier. Use the single 35mm adapter with the 4x5 carrier.
English
4
English
5
The 120 Film Adapters (Page 11)
Inserting the Carrier Into
the Scanner (Page 14)
Step 2 has the following note added:
Steps 3 and 4 on pages 11 and 12 have changed to the following:
3
Orient the 120 film adapter with the correct side up and the
notches (a) on the left. Place the unmounted film over the
opening so the image is right-reading and the top of the
image is at the top of the adapter.
Note: When inserting the 4x5 film carrier, make sure the words
"LOCK" and "UNLOCK" face upward. For the four-slide carrier,
the words "THIS SIDE UP" face upward.
a
4
Secure the film by placing the two magnets provided on the
top and bottom edges. The magnets must not extend over the
depressed channel surrounding the film placement area.
©
2000 Polaroid Corporation, Cambridge, MA 02139 USA. "Polaroid", "PolaColor"
and "SprintScan" are trademarks of Polaroid Corporation. All other product names
may be trademarks of their respective owners. All rights reserved.
PL-000000-0
|