Porter Cable Trimmer 6603 User Manual

ESPAÑOL: PÁGINA 15  
FRANÇAISE : PAGE 29  
Instruction  
manual  
Double Insulated  
Shears  
MODEL  
6603  
MODEL  
6605  
IMPORTANT  
Please make certain that the person who is  
to use this equipment carefully reads and  
understands these instructions before  
starting operations.  
To learn more about Porter-Cable  
visit our website at:  
The Model and Serial No. plate is located on the main  
housing of the tool. Record these numbers in the  
spaces below and retain for future reference.  
Model No. ______________________________________  
Type ___________________________________________  
Serial No._______________________________________  
Copyright © 2005 Porter-Cable Corporation  
Part No. 900344 - 01-24-05  
 
SAFETY GUIDELINES - DEFINITIONS  
It is important for you to read and understand this manual. The  
information it contains relates to protecting YOUR SAFETY and  
PREVENTING PROBLEMS. The symbols below are used to help  
you recognize this information.  
indicates an imminently hazardous situation which, if not  
avoided, will result in death or serious injury.  
indicates a potentially hazardous situation which, if not  
avoided,could result in death or serious injury.  
indicates a potentially hazardous situation which, if not  
avoided,may result in minor or moderate injury.  
used without the safety alert symbol indicates potentially  
hazardous situation which, if not avoided, may result in  
property damage.  
CALIFORNIA PROPOSITION 65  
Some dust created by power sanding, sawing, grinding, drilling,  
and other construction activities contains chemicals known (to the  
State of California) to cause cancer, birth defects or other reproductive harm. Some  
examples of these chemicals are:  
lead from lead-based paints  
crystalline silica from bricks and cement and other masonry products  
arsenic and chromium from chemically-treated lumber  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, always wear  
NIOSH/OSHA approved, properly fitting face mask or respirator when using  
such tools.  
3
 
GENERAL SAFETY RULES  
Read all instructions. Failure to follow all  
instructions listed below may result in electric shock, fire and/or  
serious injury. The term "power tool" in all of the warnings listed  
below refers to your mains-operated (corded) power tool or  
battery-operated (cordless) power tool.  
SAVE THESE INSTRUCTIONS  
1) Work area safety  
a) Keep work area clean and well lit. Cluttered or dark areas invite  
accidents.  
b) Do not operate power tools in explosive atmospheres, such as in the  
presence of flammable liquids, gases or dust. Power tools create  
sparks which may ignite the dust or fumes.  
c) Keep children and bystanders away while operating a power tool.  
Distractions can cause you to lose control.  
2) Electrical safety  
a) Power tool plugs must match the outlet. Never modify the plug in any  
way. Do not use any adapter plugs with earthed (grounded) power  
tools. Unmodified plugs and matching outlets will reduce risk of electric  
shock.  
b) Avoid body contact with earthed or grounded surfaces such as  
pipes, radiators, ranges and refrigerators. There is an increased risk of  
electric shock if your body is earthed or grounded.  
c) Do not expose power tools to rain or wet conditions. Water entering a  
power tool will increase the risk of electric shock.  
d) Do not abuse the cord. Never use the cord for carrying, pulling or  
unplugging the power tool. Keep cord away from heat, oil, sharp  
edges or moving parts. Damaged or entangled cords increase the risk  
of electric shock.  
e) When operating a power tool outdoors, use an extension cord  
suitable for outdoor use. Use of a cord suitable for outdoor use reduces  
the risk of electric shock.  
3) Personal safety  
a) Stay alert, watch what you are doing and use common sense when  
operating a power tool. Do not use a power tool while you are tired  
or under the influence of drugs, alcohol or medication. A moment of  
inattention while operating power tools may result in serious personal  
injury.  
b) Use safety equipment. Always wear eye protection. Safety equipment  
such as dust mask, non-skid safety shoes, hard hat, or hearing  
protection used for appropriate conditions will reduce personal injuries.  
c) Avoid accidental starting. Ensure the switch is in the off-position  
before plugging in. Carrying power tools with your finger on the switch  
or plugging in power tools that have the switch on invites accidents.  
4
 
continued  
GENERAL SAFETY RULES  
d) Remove any adjusting key or wrench before turning the power tool  
on. A wrench or a key left attached to a rotating part of the power tool  
may result in personal injury.  
e) Do not overreach. Keep proper footing and balance at all times. This  
enables better control of the power tool in unexpected situations.  
f) Dress properly. Do not wear loose clothing or jewelry. Keep your  
hair, clothing and gloves away from moving parts. Loose clothes,  
jewelry or long hair can be caught in moving parts.  
g) If devices are provided for the connection of dust extraction and  
collection facilities, ensure these are connected and properly used.  
Use of these devices can reduce dust-related hazards.  
4) Power tool use and care  
a) Do not force the power tool. Use the correct power tool for your  
application. The correct power tool will do the job better and safer at the  
rate for which it was designed.  
b) Do not use the power tool if the switch does not turn it on and off.  
Any power tool that cannot be controlled with the switch is dangerous  
and must be repaired.  
c) Disconnect the plug from the power source before making any  
adjustments, changing accessories, or storing power tools. Such  
preventive safety measures reduce the risk of starting the power tool  
accidentally.  
d) Store idle power tools out of the reach of children and do not allow  
persons unfamiliar with the power tool or these instructions to  
operate the power tool. Power tools are dangerous in the hands of  
untrained users.  
e) Maintain power tools. Check for misalignment or binding of moving  
parts, breakage of parts and any other condition that may affect the  
power tools operation. If damaged, have the power tool repaired  
before use. Many accidents are caused by poorly maintained power  
tools.  
f) Keep cutting tools sharp and clean. Properly maintained cutting tools  
with sharp cutting edges are less likely to bind and are easier to control.  
g) Use the power tool, accessories and tool bits etc., in accordance  
with these instructions and in the manner intended for the  
particular type of power tool, taking into account the working  
conditions and the work to be performed. Use of the power tool for  
operations different from those intended could result in a hazardous  
situation.  
5) Service  
a) Have your power tool serviced by a qualified repair person using only  
identical replacement parts. This will ensure that the safety of the  
power tool is maintained.  
5
 
ADDITIONAL SPECIFIC SAFETY RULES  
1. Hold power tool by insulated gripping surfaces when performing an  
operation where the cutting tool may contact hidden wiring or its own  
cord. Contact with a "live" wire will make exposed metal parts of the tool  
"live" and shock the operator.  
2. Keep hands away from cutting area. A moment of inattention while  
operating power tools may result in serious personal injury.  
3. Stay clear of end pieces that may fall after being cut off. Contact with a  
sharp edge could result in personal injury.  
4. Always keep the power cord away from the edge of the material being  
sheared. Sharp edges can result in the cord insulation being cut. This  
condition may create an electrical hazard.  
5. Wear eye and hearing protection. Always use safety glasses. Everyday  
eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT.  
Eye protection equipment should comply with ANSI Z87.1 standards.  
Hearing equipment should comply with ANSI S3.19 standards.  
6.  
Use of this tool can generate and disburse dust or other  
airborne particles, including wood dust, crystalline silica dust and  
asbestos dust. Direct particles away from face and body. Always operate  
tool in well ventilated area and provide for proper dust removal. Use dust  
collection system wherever possible. Exposure to the dust may cause  
serious and permanent respiratory or other injury, including silicosis (a  
serious lung disease), cancer, and death. Avoid breathing the dust, and  
avoid prolonged contact with dust. Allowing dust to get into your mouth or  
eyes, or lay on your skin may promote absorption of harmful material.  
Always use properly fitting NIOSH/OSHA approved respiratory protection  
appropriate for the dust exposure, and wash exposed areas with soap and  
water.  
SAVE THESE INSTRUCTIONS!  
6
 
SYMBOL  
DEFINITION  
........................ volts  
V
A
........................ amperes  
........................ hertz  
........................ watts  
........................ kilowatts  
........................ farads  
........................ microfarads  
........................ litres  
Hz  
W
kW  
F
µF  
l
g
........................ grams  
........................ kilograms  
........................ bars  
........................ pascals  
........................ hours  
........................ minutes  
........................ seconds  
........................ no-load speed  
kg  
bar  
Pa  
h
min  
s
n0  
…/min or …min 1 ......... Revolutions or reciprocations per minute  
-
or d.c. ................ direct current  
or a.c. ................ alternating current  
2
........................ two-phase alternating current  
2N  
3
........................ two-phase alternating current with neutral  
........................ three-phase alternating current  
3N  
........................ three-phase alternating current with neutral  
........................ rated current of the appropriate fuse-link in amperes  
........................ time-lag miniature fuse-link where X is the symbol  
for the time/current characteristic, as given in IEC 60127  
........................ protective earth  
........................ class II tool  
........................ IP symbol  
IPXX  
SAVE THESE INSTRUCTIONS!  
7
 
MOTOR  
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60  
cycle A.C. current and voltage within plus or minus 5 percent of that shown on  
the specification plate on the tool. Several models, however, are designed for  
A.C. current only. Refer to the specification plate on your tool for proper voltage  
and current rating.  
Do not operate your tool on a current on which the  
voltage is not within correct limits. Do not operate tools rated A.C.  
only on D.C. current. To do so may seriously damage the tool.  
EXTENSION CORD SELECTION  
If an extension cord is used, make sure the conductor size is large enough to  
prevent excessive voltage drop which will cause loss of power and possible  
motor damage. A table of recommended extension cord sizes will be found in  
this section. This table is based on limiting line voltage drop to 5 volts (10 volts  
for 230 volts) at 150% of rated amperes.  
If an extension cord is to be used outdoors, it must be marked with the suffix W-  
A or W following the cord type designation. For example – SJTW-A to indicate it  
is acceptable for outdoor use.  
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS  
Length of Cord in Feet  
115V  
230V  
25 Ft.  
50 Ft.  
50 Ft.  
100 Ft. 150 Ft. 200 Ft.  
250 Ft. 300 Ft.  
500 Ft. 600 Ft.  
400 Ft. 500 Ft.  
800 Ft. 1000 Ft.  
100 Ft. 200 Ft. 300 Ft. 400 Ft.  
0-2  
2-3  
18  
18  
18  
18  
18  
18  
18  
16  
16  
16  
14  
14  
18  
18  
18  
18  
16  
16  
14  
14  
12  
12  
12  
12  
18  
16  
16  
14  
14  
12  
12  
10  
10  
10  
8
16  
14  
14  
12  
12  
10  
10  
8
16  
14  
12  
12  
10  
10  
8
14  
12  
12  
10  
10  
8
14  
12  
10  
10  
8
12  
10  
10  
8
12  
10  
8
3-4  
4-5  
8
5-6  
8
6
6-8  
6
6
6
8-10  
10-12  
12-14  
14-16  
16-18  
18-20  
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
SAVE THESE INSTRUCTIONS!  
CARTON CONTENTS  
1) Shear  
2) Instruction Manual  
3) Replacement Parts List  
4) Combination Package  
8
 
FUNCTIONAL DESCRIPTION  
FOREWORD  
The Porter-Cable Model 6603 Shear is designed for cutting cold-rolled steel  
sheets up to 18 Ga. and stainless steel sheets up to 20 Ga. You can make  
both straight and curved cuts with a minimum radius of 7". The Shear  
removes a ¼" wide continuous curl of waste material without bending or  
burring the finished workpiece.  
The Porter-Cable Model 6605 Cement Siding Shear is designed for cutting  
cement siding. You can make both straight and curved cuts with a minimum  
radius of 7". The Shear removes a ¼" wide piece of waste material.  
ASSEMBLY  
NOTE: This tool is shipped completely assembled. No assembly time or  
tools are required.  
OPERATION  
HOW TO HOLD THE SHEAR  
The gear housing, intermediate plate, and cutting head may  
become live if the tool cuts into wiring. To prevent accidental  
shock, hold the tool as shown in Fig. 1.  
Fig. 1  
TO START AND STOP THE SHEAR  
1.  
Make sure that the power  
circuit voltage is the same as  
that shown on the specification  
plate of the drill, that the switch  
is in the “OFF” position, and  
that your hands, body, and  
clothing are clear of cutting  
head before connecting the tool  
to the power circuit.  
B
A
2. Squeeze  
the  
TRIGGER  
SWITCH (A) Fig. 2 to start the  
motor. Release the trigger to  
stop the motor.  
Fig. 2  
3. A lock button (B) Fig. 2 is  
provided to keep motor running  
without holding the trigger  
switch “ON”.  
9
 
TO LOCK the trigger switch “ON”, squeeze the trigger as far as it will go,  
push in the lock button and release the trigger.  
TO UNLOCK the lock button, squeeze the trigger and release, leaving the  
lock button free to spring out.  
NOTE: The lock button can be engaged only when the drill is running at  
maximum speed.  
Never use the lock button when a sudden stop may be  
possible.  
4. VARIABLE SPEED – As the trigger switch is squeezed, the speed  
increases.  
HOW TO USE SHEAR  
Model 6603:  
Firmly support and clamp the workpiece to ensure control. Place the side  
knives of the shear slightly on the edge of the top side of the workpiece to  
steady the tool. Squeeze the trigger switch and guide the shear into the  
work. The tool cuts freely with only slight pressure. Forcing the tool will not  
make it cut faster. Always use sharp cutters. A light coat of suitable cutting  
fluid applied along the line of cut will increase the cutter life.  
You can produce a cut-out within the perimeter of the workpiece by drilling a  
1/2" diameter starting hole and following the directions above.  
Model 6605.  
Firmly support and clamp the workpiece to ensure control.  
Position the workpiece with the hidden or back surface of  
the material facing up to reduce marring of the exposed side. To achieve  
maximum cutting efficiency, hold the bottom of stationary blades parallel to  
and against the workpiece.  
REPLACING CUTTERS  
REMOVING CUTTER BLADES  
DISCONNECT TOOL  
B
FROM POWER SOURCE.  
1. Remove the shear head from the  
motor unit. Loosen three cap screws  
(A) Fig. 3 and pull the cutter head  
forward (a light twisting motion may  
be helpful) to separate it from motor  
unit.  
A
E
2. Remove the three cap screws (A)  
from the shear housing. Retain the  
spacer bushing (C) with the middle  
cap screw).  
C
F
3. Remove the center blade by gently  
tapping it rearward. Retain the  
spacer bushing (C) removed from the  
hole in the center blade).  
C
D
4. The side knives (D) and (E) will drop  
Fig. 3  
out of the shear housing.  
10  
 
INSTALLING CUTTER BLADES  
NOTE: For Model 6605, change the side knives after they show a width wear  
pattern of fifty percent (50%).Swap the knives left to right and use them until  
the patterns meet. When the patterns meet, invert the left and right side  
knives and use them until they show a width wear pattern of fifty percent  
(50%). They can then be swapped from left to right until you use all four (4)  
sides of the blades. Never exceed 10,000 feet of cutting on a set of side  
knives. The tool will continue to cut after these landmarks are reached, but  
the power unit will become overloaded.  
DISCONNECT TOOL FROM POWER SOURCE.  
1. Place the side knives (D) and (E) back into the shear housing. Insert a  
cap screw through the center hole in the shear housing, the side knife  
(E), the spacer bushing (C), the other side knife, (D), and then thread the  
screw into the housing one or two turns. DO NOT TIGHTEN.  
2. Coat the remaining spacer bushing (C) with lubricant and insert into the  
hole in the center blade (F). Start the center blade (with spacer bushing)  
into the rear of the shear housing, and tap it forward until the hole in the  
spacer bushing aligns with the front hole in the shear housing. Insert a cap  
screw and thread it into the housing one or two turns. DO NOT TIGHTEN.  
Coat the center blade yoke area with lubricant.  
3. Insert the remaining cap screw into the rear hole in the shear housing  
and thread it into housing one or two turns. DO NOT TIGHTEN.  
4. Place the shear head on the motor unit. Seat it with a light twisting  
motion. Rotate the shear head to the desired position (any radial  
position), and tighten all three cap screws (A).  
For Model 6603, tighten all three cap screws (A) to 30-35 in-lbs. Failure to  
tighten the cap screws properly can cause the cap screws (A) to break.  
For Model 6605, tighten all three cap screws (A) to 45-50 in-lbs. Failure to  
tighten the cap screws properly can cause the cap screws (A) to break.  
11  
 
SERVICING THE ECCENTRIC BEARING  
NOTE: For model 6603 only.  
Once every three months (depending on usage), remove the shear head  
from the power unit following the instructions in the "REPLACING  
CUTTERS" section of the manual.  
Disconnect the tool from the power source before dis-  
assembling.  
Put a few drops of heavy oil on the eccentric bearing assembly (A) Fig. 4, so  
that it saturates the needle bearing. The outside surface of the eccentric  
bearing ring and the yoke of the center blade should be coated with bearing  
lubricant.  
A
Fig. 4  
12  
 
TROUBLESHOOTING  
For assistance with your tool, visit our website at www.porter-cable.com for a  
list of service centers or call the Porter-Cable help line at 1-800-487-8665.  
MAINTENANCE  
KEEP TOOL CLEAN  
Periodically blow out all air passages with dry compressed air. All plastic parts  
should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic  
parts. They could possibly dissolve or otherwise damage the material.  
Wear ANSI Z87.1 safety glasses while using compressed air.  
FAILURE TO START  
Should your tool fail to start, check to make sure the prongs on the cord plug are  
making good contact in the outlet. Also, check for blown fuses or open circuit  
breakers in the line.  
LUBRICATION  
This tool has been lubricated with a sufficient amount of high grade lubricant for  
the life of the unit under normal operating conditions. No further lubrication is  
necessary.  
BRUSH INSPECTION (If applicable)  
For your continued safety and electrical protection, brush inspection and  
replacement on this tool should ONLY be performed by an AUTHORIZED  
PORTER-CABLE SERVICE STATION or a PORTER-CABLEDELTA FACTORY  
SERVICE CENTER.  
At approximately 100 hours of use, take or send your tool to your nearest  
authorized Porter-Cable Service Station to be thoroughly cleaned and inspected.  
Have worn parts replaced and lubricated with fresh lubricant. Have new brushes  
installed, and test the tool for performance.  
Any loss of power before the above maintenance check may indicate the need  
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL  
UNDER THIS CONDITION. If proper operating voltage is present, return your  
tool to the service station for immediate service.  
13  
 
SERVICE  
REPLACEMENT PARTS  
When servicing use only identical replacement parts. For a service parts list or to  
learn more about Porter-Cable visit our website at www.porter-cable.com  
SERVICE AND REPAIRS  
All quality tools will eventually require servicing, or replacement of parts due to  
wear from normal use. For assistance with your tool, visit our website at  
www.porter-cable.com for a list of service centers or call the Customer Care  
Department at 1-800-487-8665. All repairs made by our service centers are fully  
guaranteed against defective material and workmanship. We cannot guarantee  
repairs made or attempted by others.  
Should you have any questions about your tool, feel free to write us at any time.  
In any communications, please give all information shown on the nameplate of  
your tool (model number, type, serial number, etc.).  
ACCESSORIES  
A complete line of accessories is available from your Porter-CableDelta  
Supplier, Porter-CableDelta Factory Service Centers, and Porter-Cable  
Authorized Service Stations. Please visit our Web Site www.porter-cable.com  
for a catalog or for the name of your nearest supplier.  
Since accessories other than those offered by  
Porter-CableDelta have not been tested with this product, use of  
such accessories could be hazardous. For safest operation, only  
Porter-CableDelta recommended accessories should be used  
with this product.  
WARRANTY  
PORTER-CABLE LIMITED  
ONE YEAR WARRANTY  
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original  
purchase. We will repair or replace at our option, any part or parts of the product and accessories  
covered under this warranty which, after examination, proves to be defective in workmanship or  
material during the warranty period. For repair or replacement return the complete tool or accessory,  
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.  
Proof of purchase may be required. This warranty does not apply to repair or replacement required  
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service  
Centers or Authorized Service Stations.  
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE  
OF PURCHASE.  
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,  
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING  
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY  
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL  
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied  
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights and you may also have other legal rights which vary  
from state to state.  
14  
 
PORTER-CABLE • DELTA SERVICE CENTERS  
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)  
(CENTRE DE SERVICE PORTER-CABLE • DELTA)  
Parts and Repair Service for Porter-Cable  
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable  
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)  
Delta Power Tools are Available at These Locations  
Delta)  
Cleveland 44125  
8001 Sweet Valley Drive  
Unit #19  
Phone: (216) 447-9030  
Fax: (216) 447-3097  
ARIZONA  
MINNESOTA  
Minneapolis 55429  
5522 Lakeland Avenue North  
Phone: (763) 561-9080  
Fax: (763) 561-0653  
GEORGIA  
Tempe 85282 (Phoenix)  
2400 West Southern Avenue  
Suite 105  
Phone: (602) 437-1200  
Fax: (602) 437-2200  
Forest Park 30297 (Atlanta)  
5442 Frontage Road,  
Suite 112  
Phone: (404) 608-0006  
Fax: (404) 608-1123  
OREGON  
MISSOURI  
Portland 97230  
CALIFORNIA  
North Kansas City 64116  
1141 Swift Avenue  
Phone: (816) 221-2070  
Fax: (816) 221-2897  
ILLINOIS  
4916 NE 122 nd Ave.  
Phone: (503) 252-0107  
Fax: (503) 252-2123  
Ontario 91761 (Los Angeles)  
3949A East Guasti Road  
Phone: (909) 390-5555  
Fax: (909) 390-5554  
Addison 60101 (Chicago)  
400 South Rohlwing Rd.  
Phone: (630) 424-8805  
Fax: (630) 424-8895  
PENNSYLVANIA  
St. Louis 63119  
Willow Grove 19090 (Philadelphia)  
520 North York Road  
Phone: (215) 658-1430  
Fax: (215) 658-1433  
7574 Watson Road  
Phone: (314) 968-8950  
Fax: (314) 968-2790  
Woodridge 60517 (Chicago)  
2033 West 75th Street  
Phone: (630) 910-9200  
Fax: (630) 910-0360  
San Diego 92111  
7638 Clairemont Blvd.  
Phone: (858) 277-9595  
Fax: (858) 277-9696  
NEW YORK  
TEXAS  
Flushing 11365-1595 (N.Y.C.)  
175-25 Horace Harding Expwy.  
Phone: (718) 225-2040  
Fax: (718) 423-9619  
MARYLAND  
San Leandro 94577 (Oakland)  
3039 Teagarden Street  
Phone: (510) 357-9762  
Fax: (510) 357-7939  
Carrollton 75006 (Dallas)  
1300 Interstate 35 N, Suite 112  
Phone: (972) 446-2996  
Fax: (972) 446-8157  
Elkridge 21075 (Baltimore)  
7397-102 Washington Blvd.  
Phone: (410) 799-9394  
Fax: (410) 799-9398  
NORTH CAROLINA  
Charlotte 28270  
9129 Monroe Road, Suite 115  
Phone: (704) 841-1176  
Fax: (704) 708-4625  
COLORADO  
Houston 77043  
4321 Sam Houston Parkway, West  
Suite 180  
Phone: (713) 983-9910  
Fax: (713) 983-6645  
MASSACHUSETTS  
Arvada 80003 (Denver)  
8175 Sheridan Blvd., Unit S  
Phone: (303) 487-1809  
Fax: (303) 487-1868  
Franklin 02038 (Boston)  
Franklin Industrial Park  
101E Constitution Blvd.  
Phone: (508) 520-8802  
Fax: (508) 528-8089  
OHIO  
FLORIDA  
WASHINGTON  
Columbus 43214  
4560 Indianola Avenue  
Phone: (614) 263-0929  
Fax: (614) 263-1238  
Davie 33314 (Miami)  
4343 South State Rd. 7 (441)  
Unit #107  
Phone: (954) 321-6635  
Fax: (954) 321-6638  
Auburn 98001(Seattle)  
3320 West Valley HWY, North  
Building D, Suite 111  
Phone: (253) 333-8353  
Fax: (253) 333-9613  
MICHIGAN  
Madison Heights 48071 (Detroit)  
30475 Stephenson Highway  
Phone: (248) 597-5000  
Fax: (248) 597-5004  
Tampa 33609  
4538 W. Kennedy Boulevard  
Phone: (813) 877-9585  
Fax: (813) 289-7948  
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and  
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service  
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to  
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.  
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-  
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro  
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de  
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au  
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-  
Cable  
Delta, s’adresser à tout distributeur Porter-Cable  
Delta, centre de service agréé ou centre de service d’usine Porter-Cable  
Delta. Si  
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable  
Delta le  
plus proche.  
CANADIAN PORTER-CABLE DELTA SERVICE CENTERS  
QUÉBEC  
ALBERTA  
MANITOBA  
1515 Ave.  
Bay 6, 2520-23rd St. N.E.  
Calgary, Alberta  
T2E 8L2  
1699 Dublin Avenue  
Winnipeg, Manitoba  
R3H 0H2  
St-Jean Baptiste, Suite 160  
Québec, P.Q.  
G2E 5E2  
Phone: (418) 877-7112  
Fax: (418) 877-7123  
Phone: (403) 735-6166  
Fax: (403) 735-6144  
Phone: (204) 633-9259  
Fax: (204) 632-1976  
BRITISH COLUMBIA  
8520 Baxter Place  
Burnaby, B.C.  
V5A 4T8  
Phone: (604) 420-0102  
Fax: (604) 420-3522  
ONTARIO  
1447, Begin  
St-Laurent, (Mtl), P.Q.  
H4R 1V8  
Phone: (514) 336-8772  
Fax: (514) 336-3505  
505 Southgate Drive  
Guelph, Ontario  
N1H 6M7  
Phone: (519) 767-4132  
Fax: (519) 767-4131  
The following are trademarks of PORTER-CABLE  
DELTA (Las siguientes son marcas registradas de PORTER-CABLE  
DELTA S.A.) (Les  
marques suivantes sont des marques de fabriquant de la PORTER-CABLE  
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,  
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying  
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-  
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-  
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-  
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,  
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,  
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-  
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,  
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,  
WOODWORKER’S CHOICE™.  
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.  
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden  
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et  
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.  
PC7.2-0105-164  
 

Pelco Switch VS5108 User Manual
Philips Double Oven SBC SC479 User Manual
Philips Sprinkler PM3065 User Manual
Philips TV VCR Combo 14PV100 User Manual
Philips Work Light EG1 4 User Manual
Polaroid Digital Camera PDC 1075 User Manual
Praktica Digital Camera D00390 User Manual
Prince Castle Griddle 123 User Manual
Proxima ASA Projector DP9270 User Manual
PVI Industries Water Heater PV 5369 User Manual