R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1--800--554--6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
WT200 LE
IMPORTANT MANUAL -- Do not throw away
MANUAL IMPORTANTE -- No lo descarte
MANUEL IMPORTANT -- À Conserver
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
Electrolux Home Products
250 Bobby Jones Expressway
Augusta, GA 30907
530086848
4/26/02
Copyright E2002 Electrolux Home Products, Inc.
disconnected. Keep vents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
MAINTENANCE section for information on
maintenance of the muffler and spark arrest-
ing screen.
D Never place any object in the air intake open-
ing as this could restrict proper air flow and
cause damage to the unit.
ASSEMBLY
D Never use for spreading chemicals, fertiliz-
ers, or other substances which may contain
toxic materials.
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
D To avoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
D Use only for jobs explained in this manual.
MAINTAIN YOUR UNIT PROPERLY
D Have all maintenance other than the rec-
ommended procedures described in the in-
struction manual performed by an autho-
rized service dealer.
D Disconnect spark plug before performing
maintenance except for carburetor adjust-
ments.
D Use only recommended Poulanr replace-
ment parts; use of any other parts may void
your warranty and cause damage to your
unit.
D Empty fuel tank before storing the unit. Use
up fuel left in carburetor by starting engine and
letting it run until it stops.
D Do not use any accessory or attachment
other than those recommended by manufac-
turer for use with your unit.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D Store in a dry area out of reach of children.
WARNING: If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
D A standard screwdriver is required for as-
sembly.
BLOWER TUBE ASSEMBLY
D Align the rib on the blower tube with the
groove in the blower outlet; slide the tube
into place.
NOTE: Tube clamp must be loose enough to
allow blower tube to be inserted in blower out-
let. Loosen tube clamp by turning knob coun-
terclockwise.
Blower
Blower
Outlet
Tube
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An antivibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
Groove
Rib
D Tighten the tube clamp by turning the knob
clockwise.
D To remove the tube, turn the knob counter-
clockwise to loosen clamp; remove tube.
VACUUM BAG ASSEMBLY
D Open the zipper on the vacuum bag and in-
sert the elbow tube.
D Push the small end of the elbow tube
through the small opening in the bag.
Elbow
Tube
Small
Opening
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
Zipper
Opening
Rib
NOTE: Make sure edge of the small opening
is flush against the flared area of the elbow
tube, and the rib on the elbow tube is on the
bottom.
D Close the zipper on the bag. Make sure the
zipper is closed completely.
to do so is a violation of the law. Refer to the D Remove blower tube from engine.
-- 3 --
Knob
Rib
Hooks
Groove
D When converting back to the blower fea-
ture, make sure latch on the vacuum inlet
cover is securely fastened.
SHOULDER STRAP ADJUSTMENT
D Hold the unit as shown.
D Insert the elbow tube into the blower outlet.
Make sure elbow tube rib is aligned with the
blower outlet groove.
D Pass the shoulder strap over your head and
onto your right shoulder.
D Extend your left arm toward the rear of the
vacuum bag.
D Turn clamp knob clockwise to tighten.
D Adjust shoulder strap until the vacuum bag/
shoulder strap seam lies between your
thumb and index finger.
VACUUM TUBE ASSEMBLY
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury.
D Align the lower vacuum tube as shown.
Push lower vacuum tube into upper vacu-
um tube.
D Make sure air flows freely from the elbow
tube into bag. If bag is kinked, the unit will
not operate properly.
Upper Vacuum
Tube
Lower Vacuum Tube
D Insert a screwdriver into the latch area on
the vacuum inlet cover.
Blower
Outlet
Latch
Ar
Latch Area
Vacuum
Inlet Cover
USING YOUR UNIT
WARNING: You MUST make sure
the tubes are secure before using the unit.
OPERATING POSITION
D Gently tilt the handle of the screwdriver to-
ward the back of the unit while pulling up on
the vacuum inlet cover with your other
hand.
D Hold the vacuum inlet cover open until up-
per vacuum tube is installed.
ye
otec
Vacuum Inlet
Retaining Post
Vacuum
Inlet
Blower
Vacuum
Cover
OPERATING TIPS
D Place the hooks on the vacuum tube on the S While vacuuming or blowing debris, hold
retaining posts; pivot tube into position. Se-
cure vacuum tube by turning the knob
clockwise until tight.
the unit with the muffler side facing away
from your body and clothes (see illustration
above).
-- 4 --
S To reduce the risk of hearing loss
associated with sound level(s), hearing
protection is required.
STARTING
S To reduce the risk of injury associated with
contacting rotating parts, stop the engine be-
fore installing or removing attachments. Do
not operate without guard(s) in place.
S Operate power equipment only at reasonable
hours--not early in the morning or late at night
when people might be disturbed. Comply with
times listed in local ordinances. Usual recom-
mendations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
S To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S Use rakes and brooms to loosen debris be-
fore blowing.
S In dusty conditions, slightly dampen sur-
faces or use a mister attachment when wa-
ter is available.
S Conserve water by using power blowers
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S Watch out for children, pets, open windows,
or freshly washed cars. Blow debris away
safely.
TO STOP THE ENGINE
D To stop the engine, move the throttle lever
to the STOP position.
BEFORE STARTING THE ENGINE
D Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
D Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
STARTING POSITION
Blower
S Use the full blower nozzle extension so the
air stream can work close to the ground.
S After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
WARNING: When starting engine,
hold the unit as illustrated. Do not set unit on any
surface except a clean, hard area when starting
engine or while engine is running. Debris such
as gravel, sand, dust, grass, etc. could be
picked up by the air intake and thrown out
through the discharge opening, damaging the
unit or property, or causing serious injury to by-
standers or the operator.
FUELING
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on
unleaded gasoline. Gasoline must be mixed
S Move throttle lever to the
position.
S Move choke lever to the FULL CHOKE
position.
S Slowly press the primer button 8 times.
with
a
good quality synthetic 2--cycle
air--cooled engine oil designed to be mixed at
a ratio of 40:1. Poulan/Weed Eater brand
synthetic oil is recommended. A 40:1 ratio is
obtained by mixing 3.2 ounces of oil with 1
gallon of unleaded gasoline. When mixing
fuel follow the instructions printed on the
container. Always read and follow the safety
rules under HANDLE FUEL WITH
CAUTION.
T
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid
engine problems, empty the fuel system
before storage for 30 days or longer. Drain the
gas tank, start the engine and let it run until the
fuel lines and carburetor are empty. Use fresh
fuel next season.
Choke Lever
S Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls (be-
low 30_ F, 8 pulls).
NOTE: If engine attempts to start before the
th
5
pull, go to next step immediately.
-- 5 --
S Move the choke lever to the HALF CHOKE
position.
S Vacuum Bag -- Do not use vacuum bag if it
is torn or damaged.
S Pull the starter rope sharply until the engine
runs, but no more than 5 pulls (below 30_ F,
10 pulls). Run engine for 5 seconds, then
move choke lever to the RUN position.
S Allow the unit to run for 30 more seconds at
the RUN position before moving the throttle
INSPECT AND CLEAN UNIT AND
DECALS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a mild deter-
gent.
lever to
position.
S Wipe off unit with a clean dry cloth.
If engine has not started after 5 pulls (at HALF
CHOKE), repeat STARTING A COLD ENGINE
procedure. If engine still does not start, proceed
to STARTING A FLOODED ENGINE.
CLEAN AIR FILTER
STARTING A WARM ENGINE
S Move throttle lever to the
position.
Air Filter
Cover
S Pull starter rope sharply until engine runs,
but no more than 5 pulls.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.
STARTING A FLOODED ENGINE
S Move the choke lever to the RUN position.
S Move throttle lever to the
position.
S Pull rope to clear engine of excess fuel.
This could require pulling the starter rope
many times.
Screws
If unit still doesn’t start, call 1-800-554-6723.
Air Filter
Cleaning the air filter:
MAINTENANCE
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean or replace
air filter after every 5 hours of operation or
yearly, whichever comes first.
WARNING: Avoid touching muffler
unless engine and muffler are cold. A hot
muffler can cause serious burns.
S Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
S Remove parts as illustrated.
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instruct-ed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
NOTE: Do not clean filter in gasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emis-
sions.
S Wash the filter in soap and water.
S Allow filter to dry.
S Apply a few drops of oil to the filter; squeeze
filter to distribute oil.
S Replace parts.
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
S Twist, then pull off spark plug boot.
S Remove spark plug from cylinder and dis-
card.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Muffler
S Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
S Reinstall the spark plug boot.
CHECK FOR DAMAGED OR WORN
PARTS
REPLACE FUEL FILTER
To replace fuel filter, drain unit by running it dry
Contact an authorized service dealer for re- of fuel, then remove fuel cap from tank. Pull fil-
placement of damaged or worn parts.
S Fuel Tank -- Do not use unit if fuel tank shows Install new fuel filter on fuel line; reinstall
signs of damage or leaks. parts.
ter from tank and remove it from the fuel line.
-- 6 --
Replace the spark arresting screen every 50
hours of operation or if any damage or breaks
in the screen are noted.
NOTE: Do not attempt to clean the spark ar-
Fuel Line
Fuel Filter
resting screen.
S Remove muffler cover.
S Loosen and remove both screws from the
exhaust diverter.
S Remove the exhaust diverter and spark ar-
resting screen.
S Install new spark arresting screen.
S Reinstall exhaust diverter and both screws.
Tighten screws securely.
CHECK MUFFLER MOUNTING
S Reinstall muffler cover and 2 screws. Tight-
en screws securely.
NOTE: If any part of the muffler is cracked,
broken or damaged, we recommend that the
muffler be replaced.
SCREWS
Once each year, ensure muffler mounting
screws are secure and tightened properly to
prevent damage.
Cap Screws
SERVICE
We recommend all service and adjustments
not listed in this manual be performed by an
authorized service dealer.
Muffler Cover
CARBURETOR ADJUSTMENTS
Your carburetor is equipped with limiter caps.
Adjusting the carburetor is a complicated
task. We recommend that you take your unit
to an an authorized service dealer. Damage
will occur if you turn the needles beyond the
limiter stops.
Mounting
Screw Holes
NOTE: The muffler mounting screws are lo-
cated behind the cap screws. The cap
screws must be removed to access the
mounting screws.
S Remove muffler cover.
S Loosen and remove the 2 cap screws from
the muffler mounting screw holes.
S Tighten the 2 mounting screws securely.
S Reinstall and tighten the 2 cap screws se-
curely.
STORAGE
S Reinstall muffler cover and 2 screws. Tight-
en securely.
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
As the unit is used, carbon deposits build up
on the muffler and spark arresting screen,
and must be removed to avoid creating a fire
hazard or affecting engine performance.
S Store unit and fuel well out of the reach of
children.
TOP VIEW OF MUFFLER
Exhaust
Diverter
NEED ASSISTANCE?
NEED ASSISTANCE?
Call: 1-800-554-6723.
NEED A SERVICE PART?
Contact your dealer.
Screws
-- 7 --
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of the
recommended remedies below other than remedies that require operation of the unit.
TROUBLE
Engine will not
start.
CAUSE
REMEDY
S Engine flooded.
S See “Starting Instructions.”
S Fill tank with correct fuel mixture.
S Install new spark plug.
S Fuel tank empty.
S Spark plug not firing.
S Fuel not reaching carburetor.
S Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
S Compression low.
S Contact an authorized service dealer.
S Fuel not reaching carburetor.
S Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
S See “Carburetor Adjustments.”
S Contact an authorized service dealer.
S Contact an authorized service dealer.
Engine will not
idle properly.
S Carburetor requires adjustment.
S Crankshaft seals worn.
S Compression low.
S Air filter dirty.
S Clean or replace air filter.
Engine will not
accelerate,
lacks power, or
dies under a
load.
S Fuel not reaching carburetor.
S Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
S Spark plug fouled.
S Clean or replace spark plug; re-gap.
S Replace screen.
S See “Carburetor Adjustments.”
S Contact an authorized service dealer.
S Contact an authorized service dealer.
S Spark arresting screen clogged.
S Carburetor requires adjustment.
S Carbon build up.
S Compression low.
S Adjust choke.
S Choke partially on.
Engine
S Empty fuel tank and refill with
correct fuel mixture.
S Fuel mixture incorrect.
smokes
excessively.
S Clean or replace air filter.
S See “Carburetor Adjustments.”
S Air filter dirty.
S Carburetor requires adjustment.
S See “Fueling Your Unit.”
S Fuel mixture incorrect.
S Spark plug incorrect.
S Carburetor requires adjustment.
S Carbon build up.
Engine
runs hot.
S Replace with correct spark plug.
S See “Carburetor Adjustments.”
S Contact an authorized service dealer.
cover predelivery setup or normal adjustments
explained in the instruction manual.
LIMITED WARRANTY
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
ELECTROLUX HOME PRODUCTS, INC.,
warrants to the original purchaser that each new
Poulanr brand gasoline tool or attachment is
free from defects in material and workmanship
and agrees to repair or replace under this war-
ranty any defective gasoline product or attach-
ment as follows from the original date of purcha-
se
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
2 YEARS -- Parts and Labor, when used for
household purposes.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
90 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Additionally,
this warranty does not cover tune-ups, spark
plugs, filters, starter ropes, starter springs, cut-
ting line, or rotating head parts that will wear and
require replacement with reasonable use during
The policy of ELECTROLUX HOME PROD-
UCTS, INC., is to continuously improve its
products. Therefore, ELECTROLUX HOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obliga-
the warranty period. This warranty does not tion to any purchaser.
-- 8 --
WARRANTY COMMENCEMENT DATE: The
warranty period begins on the date the small
off--road engine is purchased. LENGTH OF
COVERAGE: This warranty shall be for a peri-
od of two years from the initial date of purchase.
WHAT IS COVERED: REPAIR OR RE-
PLACEMENT OF PARTS. Repair or replace-
ment of any warranted part will be performed at
no charge to the owner at an approved POU-
LAN/WEED EATER servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
POULAN/WEED EATER at 1--800--554--6723
WARRANTY PERIOD: Any warranted part
which is not scheduled for replacement as re-
quired maintenance, or which is scheduled only
for regular inspection to the effect of “repair or
replace as necessary” shall be warranted for 2
years. Any warranted part which is scheduled
for replacement as required maintenance shall
be warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS: The owner shall not be charged
for diagnostic labor which leads to the deter-
mination that a warranted part is defective if the
diagnostic work is performed at an approved
POULAN/WEED EATER servicing center.
CONSEQUENTIAL DAMAGES: POULAN/
WEED EATER may be liable for damages to
other engine components caused by the failure
of a warranted part still under warranty. WHAT
IS NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD--ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty claim.
POULAN/WEED EATER is not liable to cover
failures of warranted parts caused by the use of
add--on or modified parts. HOW TO FILE A
CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service
center or call POULAN/WEED EATER at
U.S. EPA/CALIFORNIA
EMISSION CONTROL
WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
TIONS: The U.S. Environmental Protection
Agency/California Air Resources Board and
POULAN/WEED EATER, DIVISION OF WCI
OUTDOOR PRODUCTS, INC., are pleased to
explain the emissions control system warranty
on your year 2000--2003 small off--road engine.
In California, all new small off--road engines
must be designed, built, and equipped to meet
the State’s stringent anti--smog standards.
POULAN/WEED EATER must warrant the
emission control system on your small off--road
engine for the periods of time listed below pro-
vided there has been no abuse, neglect, or im-
proper maintenance of your small off--road en-
gine engine. Your emission control system in-
cludes parts such as the carburetor and the igni-
tion system. Where a warrantable condition ex-
ists, POULAN/WEED EATER will repair your
small off--road engine engine at no cost to you.
Expenses covered under warranty include
diagnosis, parts and labor. MANUFACTUR-
ER’S WARRANTY COVERAGE: If any emis-
sions related part on your engine (as listed un-
der Emissions Control Warranty Parts List) is
defective or a defect in the materials or work-
manship of the engine causes the failure of such
an emission related part, the part will be repaired
or replaced by POULAN/WEED EATER.
OWNER’S WARRANTY RESPONSIBILI-
TIES: As the small off--road engine engine own-
er, you are responsible for the performance of
the required maintenance listed in your instruc-
tion manual. POULAN/WEED EATER recom-
mends that you retain all receipts covering
maintenance on your small off--road engine, but
POULAN/WEED EATER cannot deny warran-
ty solely for the lack of receipts or for your failure
to ensure the performance of all scheduled 1--800--554--6723. WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all POULAN/WEED
EATER service centers. call: 1--800--554--6723
maintenance. As the small off--road engine en-
gine owner, you should be aware that POULAN/
WEED EATER may deny you warranty cover-
age if your small off--road engine engine or a MAINTENANCE, REPLACEMENT AND RE-
part of it has failed due to abuse, neglect, im- PAIR OF EMISSION RELATED PARTS: Any
POULAN/WEED EATER approved replace-
ment part used in the performance of any war-
proper maintenance, unapproved modifications,
or the use of parts not made or approved by the
original equipment manufacturer. You are re- ranty maintenance or repair on emission related
sponsible for presenting your small off--road en- parts will be provided without charge to the own-
er if the part is under warranty. EMISSION
CONTROL WARRANTY PARTS LIST: Car-
gine to a POULAN/WEED EATER authorized
repair center as soon as a problem exists. War-
ranty repairs should be completed in a reason- buretor, Ignition System: Spark Plug (covered
able amount of time, not to exceed 30 days. If up to maintenance schedule), Ignition Module,
you have any questions regarding your warran- Muffler including catalyst. MAINTENANCE
STATEMENT: The owner is responsible for the
ty rights and responsibilities, you should contact
your nearest authorized service center or call performance of all required maintenance as de-
POULAN/WEED EATER at 1--800--554--6723. fined in the instruction manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 9 --
|