R
Please do not return product to retailer.
Por favor, no devuelva el producto al lugar de compra.
Veuillez ne pas retourner le produit au détaillant.
1--800--554--6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
PP325
For Occasional Use Only
DANGER:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
PELIGRO:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
DANGER:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Poulan PRO
7349 Statesville Road
Charlotte, NC 28269
115274026 Rev. 2 3/1/10 BRW
IDENTIFICATION OF SAFETY SYMBOLS
Assist handle to be positioned only below the arrow.
Never allow children to operate this unit.
Store unit indoors in a high, dry place out of the reach of
children. Store unit and fuel in area where fuel vapors can-
not reach sparks or open flames from water heaters, electric
motors or switches, furnaces, etc.
When servicing unit, use only identical replacement
parts.
Always stop unit and disconnect spark plug before clean-
ing or servicing.
WARNING: Fire hazard. Never mix, pour, or store gasoline or
use the unit near a flame or sparks (including smoking, open flames, or
work that can cause sparks).
Use unleaded gasoline and two--stroke oil mixed at a ratio of 40:1
(2.5%).
SAFETY RULES
WARNING: When using gardening
appliances, basic safety precautions must al-
ways be followed to reduce the risk of fire and
serious injury.
DANGER: This power tool can be dan-
gerous! This unit can cause serious injury in-
cluding amputation or blindness to the operator
and others. The warnings and safety instruc-
tions in this manual must be followed to provide
reasonable safety and efficiency in using the
unit. The operator is responsible for following the
warnings and instructions in this manual and on
3
the unit. Read the entire instruction manual be-
fore assembling and using the unit! Restrict the
use of this unit to persons who read, under-
stand, and follow the warnings and instructions
in this manual and on the unit. Never allow chil-
dren to operate this unit.
S Throw away blades that are bent, warped,
cracked, broken, or damaged in any other
way. Replace trimmer head parts that are
cracked, chipped, broken, or damaged in
any other way before using the unit.
S Maintain unit according to recommended
procedures. Keep blade sharp. Keep cut-
ting line at the proper length.
S Use only Poulan PRO brand replacement
line. Never use wire, rope, string, etc.
S Install required shield properly before using
the unit. Use the metal shield for all metal
blade use. Use the plastic shield for all line
trimmer use.
INSTRUCTION
MANUAL
SAFETY INFORMATION
ON THE UNIT
WARNING: Do not use trimmer head
S Use only specified blade or trimmer head;
make sure it is properly installed and se-
curely fastened.
as a fastening device for the blade.
S Never start engine with clutch shroud re-
moved. The clutch can fly off and cause se-
rious injury.
S Besureblade or trimmer head stops turning
when engine idles.
S Make carburetor adjustments with the low-
er end supported to prevent blade or trim-
mer line from contacting any object. Hold
unit by hand; do not use the shoulder strap
for support.
If situations occur which are not covered in this
manual, use care and good judgment. If you
need assistance, contact contact an authorized
service dealer or call 1--800--554--6723.
S Keep others away when making carburetor
adjustments.
OPERATOR SAFETY
S Use only recommended Poulan PRO ac-
cessories and replacement parts.
S Have all maintenance and service not ex-
plained in this manual performed by your au-
thorized service dealer.
S Dress properly. Always wear safety
glasses or similar eye protection when op-
erating, or performing maintenance on your
unit (safety glasses are available). Eye
protection should be marked Z87.
S Always wear face or dust mask if operation
is dusty.
FUEL SAFETY
S Mix and pour fuel outdoors.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or
the unit or while using the unit.
S Always wear heavy, long pants, long sleeves,
boots, and gloves. Wearing safety leg guards
is recommended.
S Always wear foot protection. Do not go
barefoot or wear sandals.
S Secure hair above shoulder length. Secure
or remove loose clothing and jewelry or cloth-
ing with loosely hanging ties, straps, tassels,
etc. They can be caught in moving parts.
S Being fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line/blade.
S Avoid spilling fuel or oil. Wipe up all fuel
spills before starting engine.
S Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S Stop engine and allow it to cool before re-
moving fuel cap.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the car-
buretor by starting the engine and letting it
run until it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
S Always store gasoline in a container ap-
proved for flammable liquids.
S Stay Alert. Do not operate unit when you are
tired, ill, upset or under influence of alcohol,
drugs, or medication. Watch what you are do-
ing; use common sense.
S Wear hearing protection.
S Never start or run the engine inside a
closed room or building. Breathing exhaust
fumes can kill.
CUTTING SAFETY
S Keep handles free of oil and fuel.
S Always use the handlebar and a properly
adjusted shoulder strap with a blade (see
ASSEMBLY).
WARNING: Inspect the area to be
cut before each use. Remove objects (rocks,
broken glass, nails, wire, string, etc.) which
can be thrown or become entangled in the
blade or trimmer head.
S Keep others including children, animals,
bystanders, and helpers at least 50 feet (15
meters) away. Bystanders should be en-
couraged to wear safety glasses. Stop engine
immediately if you are approached.
UNIT/MAINTENANCE SAFETY
WARNING: Stop unit anddisconnect
the spark plug before performing mainte-
nance (except carburetor adjustments).
S Look for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep unit in good
working condition.
4
S Always keep engine on the right--hand side
of your body.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnor-
mal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti--vibration system does not guarantee the
avoidance of these problems. Users who oper-
ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
S Hold the unit firmly with both hands.
S Keep firm footing and balance. Do not over-
reach.
S Keep blade or trimmer head below waist
level. Do not raise engine above your waist.
S Keep all parts of your body away from blade,
trimmer head, and muffler when engine is run-
ning. A hot muffler can cause serious burns.
S Cut from your left to your right. Cutting on
right side of the shield will throw debris
away from the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Stop the unit before carrying.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark ar-
resting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and Washing-
ton require by law that many internal combus-
tion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser-
vice. After 50 hours of use, we recommend that
your muffler be serviced or replaced by your au-
thorized service dealer.
S Keep muffler away from your body.
S Allow the engine to cool and secure the unit
before storing or transporting it in a vehicle.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in thecarbu-
retor by starting the engine and letting it run
until it stops.
S Store unit so the blade or line limiter blade
cannot accidentally cause injury. The unit
can be hung by the shaft.
S Store unit out of reach of children.
WARNING: The engine exhaust
from this product contains chemicals known
totheStateof California tocause cancer, birth
defects or other reproductive harm.
ASSEMBLY
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
TOOLS REQUIRED
S Hex wrench (provided)
S Adjustable wrench
S Phillips screwdriver
CARTON CONTENTS
Check carton contents against the following list:
S Powerhead
S Lower attachment (with trimmer head
installed)
S Cupped washer
S Large nut for installing blades
S Hex wrench
INSTALLING BRUSHCUTTER
ATTACHMENT
S Handlebar
S Bracket cover
CAUTION: When installing brushcutter at-
tachment, place the unit on a flat surface for
stability.
S Bracket cover screws (2)
S Metal blade shield
S Blade shield screws (4)
S 4--point weed blade
S Plastic shield
1. Loosen the coupler by turning the knob
counterclockwise.
S Wing nut (screwed onto plastic shield)
S Shoulder strap with warning
S Container of oil
Coupler
Shipping
WARNING: Always stop unit anddis-
connect spark plug before performing any as-
sembly procedures.
protector
EN
Knob
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
TIGHTEN
2. Remove shipping protector from coupler.
3. Remove the shaft cap from the brushcutter
attachment (if present).
5
4. Position locking/release button of attach-
ment into guide recess of coupler.
5. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
ASSEMBLY OF SHOULDER STRAP
WARNING: Proper shoulder strap
and handlebar adjustments must be made
with the engine completely stopped before
using unit.
1. Insert your right arm and head through
the shoulder strap and allow it to rest on
your left shoulder. Make sure the danger
sign is on your back and the hook is tothe
right side of your waist.
NOTE: A one-half twist is built in the shoul-
der strap to allow the strap to rest flat on the
shoulder.
2. Adjust the strap, allowing the hook to be
about 6 inches (15 cm) below the waist.
3. Fasten the strap hook to the clamp located
between the trigger handle and the handle-
bar clamp base and lift the tool to the oper-
ating position.
4. Try on shoulder strap and adjust for fit
and balance before starting the engine or
beginning a cutting operation.
NOTE: It may be necessary to relocate the
shoulder strap clamp on the shaft for proper
balancing of unit.
6. Before using the unit, tighten the knob se-
curely by turning clockwise.
Primary Hole
Coupler
Guide Recess
Locking/
Release
Button
Upper
Shaft
Attachment
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit. All attachments are designed
to be used in the primary hole unless other-
wise stated in the applicable attachment in-
struction manual. Using the wrong hole could
lead to serious injury or damage to the unit.
TO RELOCATE SHOULDER STRAP
CLAMP:
1. Loosen and remove both clamp screws.
2. Place the upper shoulder strap clamp
over the shaft.
3. Position the lower shoulder strap clamp
under the shaft and align the upper and
lower clamp screw holes.
Locking/Release
Button in Primary Hole
houlder
amp
For assembly of optional attachments (see list
on page 10), refer to the ASSEMBLY section of
the applicable attachment instruction manual.
ATTACHING THE HANDLEBAR
DANGER: To avoid serious injury, the
barrier portion of the handlebar must be installed
as shown to provide a barrier between operator
and the spinning blade.
Lower Shoulder
Strap Clamp
Screws
1. Locate the decal on the handlebar. This
decal includes an arrow. Position the
handlebar with the mounting bracket at
the end of the arrow.
4. Insert two screws into the screw holes.
5. Secure shoulder strap clamp by tighten-
ing screws with a hex wrench.
2. Position the bracket cover over the han-
dlebar. Again make sure the handlebar is
at the end of the arrow.
HARNESS
ADJUSTMENT
FOR BALANCE
3. Insert screws and hand tighten only. Be
sure the handlebar is installed correctly;
then, tighten each screw securely with the
hex wrench.
Screw
bar
6 inches
4 -- 12 inches
(15 cm)
(10 -- 30 cm)
below
waist
above
ground
30 inches
(76 cm)
Bracket Cover
Mounting Brack
6
NOTE: If your unit has a plastic cover over
the threads on the threaded shaft, removethe
covering to expose the threads. Beforeinstal-
ling the trimmer head, make sure the dust cup
and retaining washer are positioned on the
gearbox as shown below.
30 inches
(76 cm)
Bracket
Slot
Wing Nut
Gearbox
Shield
Dust Cup
CONFIGURING YOUR UNIT
You can configure your unit using a cutting head
for grass and light weeds, or a weed blade for
cutting grass, weeds, and brush up to 1/2 inch
(1 cm) in diameter. To assemble your unit, go to
the section for the desired configuration and fol-
low the instructions.
Retaining Washer
NOTE: Make sure all parts are properly
installed as shown in the illustration before
installing the trimmer head.
ASSEMBLY INFORMATION --
TRIMMER HEAD
5. Align hole in the dust cup with the hole in
the side of the gearbox by rotating the
dust cup.
6. Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while tightening trimmer head.
TRIMMER
HEAD
Screwdriver
NOTE:Remove the blade and metal shield be-
fore attaching the plastic shield and trimmer
head. To remove blade, align hole in the dust
cup with the hole in the side of the gearbox by
rotating the blade. Insert a small screwdriver
into aligned holes. This will keep the shaft from
turning while loosening the blade nut. Remove
blade nut by turning clockwise. Remove the
screwdriver. Remove both washers and blade.
To remove metal shield, loosen and remove the
four mounting screws. See ATTACHING THE
METAL SHIELD and INSTALLATION OF THE
METAL BLADE for illustrations. Be sure to store
all parts and instructions for future use.
7. While holding the screwdriver in position,
thread trimmer head onto the shaft in the
direction shown on the decal (counter-
clockwise). Tighten until secure.
NOTE: The retaining washer must be posi-
tioned with the raised section facing toward the
gearbox.
ASSEMBLY INFORMATION -- WEED
BLADE
WEED
BLADE
ATTACHING THE PLASTIC SHIELD
AND TRIMMER HEAD
WARNING: The shield must be prop-
erly installed. The shield provides partial
protection to the operator and others from the
risk of thrown objects, and is equipped with a
line limiter blade which cuts excess line to the
proper length. The line limiter blade (on un-
derside of shield) is sharp and can cut you.
1. Remove wing nut from shield.
NOTE: Remove the trimmer head and plastic
shield before attaching the metal shield and
installing the weed blade. To remove the trim-
mer head, align hole in the dust cup with the hole
in the side of the gearbox by rotating the dust
cup. Insert a small screwdriver into aligned
2. Insert bracket into slot on shield.
3. Pivot shield until bolt passes throughhole
in bracket.
4. Tighten the wing nut securely.
7
holes. This will keep the shaft from turning while
loosening the trimmer head. Remove the trim-
mer head by turning clockwise. Remove the
screwdriver. To remove the plastic shield, loos-
en and remove wing nut. Pivot shield to release
bracket from slot. See INSTALLATION OF
THECUTTING HEADand ATTACHING THE
PLASTIC SHIELD for illustrations. Be sure to
store all parts and instructions for future use.
Never use the trimmer head with the metal
blade installed.
2. Install the blade and the retaining washer
over the threaded shaft.
3. Make sure the raised part of the retaining
washer is facing the gearbox and the
raised area fits into the hole in the center
of the blade.
4. Slide the blade and retaining washer onto
the shaft of the gearbox.
5. Place the cupped washer onto the shaft.
Make sure the cupped side of the washer
is toward the blade.
6. Install the blade nut by threading onto the
shaft counterclockwise.
ATTACHING THE METAL SHIELD
WARNING: The metal shield must
be properly installed on the tool anytime the
tool is used witha blade. The forwardtip of the
metal shield helps to reduce the occurrence
of blade thrust which can cause serious injury
such as amputation to the operator or by-
standers. Failure to install the shield in the
position shown can result in serious injury to
the operator. The length of the shield must be
aligned with the length of the shaft.
Gearbox
Shield
1. Place the metal shield under the gearbox,
and align the screw holes.
Dust Cup
Threaded Shaft
ade
Retaining
Washer
Gearbox
Cupped
Washer
Nut
Shield
NOTE: Make sure all parts are in place as il-
lustrated, and the blade is sandwiched between
the dust cup and the retaining washer. There
should be no space between the blade and the
dust cup or the retaining washer.
2. Insert and thread the 4 mounting screws
through the holes of the gearbox and the
metal shield. Tighten evenly and secure-
ly with the hex wrench provided.
INSTALLATION OF THE METAL
BLADE
7. Align hole in dust cup with hole in side of
gearbox by rotating the blade.
8. Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while tightening the blade nut.
WARNING: Wear protective gloves
when handling or performing maintenance on
the blade to avoid injury. The blade is sharp and
can cut you even when it is not moving.
Screwdriver
WARNING: Do not use any blades, or
fastening hardware other than the washers and
nuts shown in the following illustrations. These
parts must be provided by Poulan/WEED
EATER and installed as shown below. Failure to
use proper parts can cause the blade to fly off
and seriously hurt you or others.
NOTE: The dust cup and retaining washer are
located on the gearbox shaft and not in the parts
bag. All other fasteners mentioned in the follow-
ing assembly steps are in the parts bag.
1. Remove the retaining washer from the
threaded shaft of the gearbox. Leave the
dust cup on the shaft.
9. TIghten blade nut firmly with a wrench while
holding screwdriver in position.
10. Remove the screwdriver.
11. Turn blade by hand. If the blade binds
against the shield, or appears to be uneven,
the blade is not centered, and you must re-
install.
NOTE: To remove blade, insert screwdriver
into aligned holes. Unthread the nut and re-
move parts. Be sure to store parts and instruc-
tions for future use.
8
OPERATION
KNOW YOUR UNIT
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
TimmeHead
Muffler
Handlebar
Coupler
Shaft
d
Throttle Trigger
Line Limiter
Blade
Spark Plug
Primer Bulb
ON/STOP
Switch
Blade
rt Lever
Starter Handle
ON/STOP SWITCH
START LEVER
The ON/STOP switch is located on the trigger
handle and is used to stop the engine. To stop
the engine, push and release the engine
ON/STOP switch.
The START LEVER helps to supply fuel tothe
engine to aid in starting. Activate the starting
system by moving the start lever to the
START position. DO NOT squeeze the
throttle trigger until the engine has started and
runs. After the engine starts, allow the engine
to warm--up 10--15 seconds, then fully
squeeze the throttle trigger to deactivate the
starting system.
PRIMER BULB
The PRIMER BULB removes air from thecar-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
COUPLER
The COUPLER enables optional attach-
ments to be installed on the unit.
oil is recommended. Mix gasoline and oil at a ra-
tio of 40:1. A 40:1 ratio is obtained by mixing 3.2
fluid ounces (95 ml) of oil with 1 gallon (4 liters)
of unleaded gasoline. DO NOT USE automotive
oil or marine oil. These oils will cause engine
damage. When mixing fuel, follow instructions
printed on container. Once oil is added to gaso-
line, shake container momentarily to assure that
the fuel is thoroughly mixed. Always read and
follow the safety rules relating to fuel before fuel-
ing your unit.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
CAUTION: Never use straight gasoline in
your unit. This will cause permanent engine
damage and void the limited warranty.
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2-cycle synthetic oil into
one gallon of fresh gas.
FUEL REQUIREMENTS
This engine requires the use of minimum 87
octane [R+M]/2 clean gasoline.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle air-
cooled engine oil designed to be mixed at a ratio
of 40:1. Poulan/WEED EATER brand synthetic
IMPORTANT
Use of alcohol blended fuels (called gasohol or
using ethanol or methanol) can cause major en-
gine performance and durability problems.
9
WARNING: Alternative fuels (not gas-
oline) such as E--15 (15% alcohol), E--20 (20%
alcohol), E--85 (85% alcohol) are NOT classified
as gasoline and are NOT approved for use in
2--stroke gasoline engines. Use of alternative
fuels will cause problems such as: improper
clutch engagements, overheating, vapor lock,
power loss, lubrication deficiency, deterioration
of fuel lines, gaskets and internal carburetor
components, etc. Alternative fuels cause high
moisture absorption into the fuel/oil mixture
leading to oil and fuel separation.
Primer Bulb
HOW TO STOP YOUR UNIT
Start Lever
S Release the throttle trigger.
S Push and release the engine ON/STOP
switch. The switch will automatically return to
the ON position. Wait 5 seconds before at-
tempting to restart unit to allow switch to reset.
Starter Handle
HOW TO START YOUR UNIT
WARNING: Avoid any contact with the
4. Pull starter rope handle sharply until en-
gine starts and runs.
5. Allow unit to run for 10--15 seconds, then
fully squeeze the throttle trigger to disen-
gage the starting system.
muffler. A hot muffler can cause serious burns.
Starting position
STARTING A WARM ENGINE
1. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
engine runs smoothly..
3. Pull starter rope sharply while squeezing
throttle trigger until engine runs.
NOTE: Normally, the warm starting proce-
dure can be used within 5--10 minutes after
the unit is turned off. If the unit sits for more
than 10 minutes without being ran, it will be
necessary to start the unit by following the
steps under STARTING A COLD ENGINE or
following the starting instruction steps shown
on the unit.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the start lever to the RUN position. Fully
squeeze throttle trigger. Pull the starter han-
dle repeatedly while squeezing throttle trigger
until engine starts and runs. This could re-
quire pulling the starter handle many times,
depending on how badly the unit is flooded.
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1-800-554 -6723.
STARTING A COLD ENGINE
NOTE: DO NOT squeeze the throttle trigger
until the engine has started and runs.
1. Set unit on a flat surface.
2. Slowly press the primer bulb 6 times.
3. Move the start lever to the START posi-
tion.
OPERATING THE COUPLER
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
MODEL:
Edger . . . . . . . . . . . . . . . . . . . . . PP1000E
Cultivator . . . . . . . . . . . . . . . . . . PP2000T
Blower . . . . . . . . . . . . . . . . . . . . PP3000B
Pruner . . . . . . . . . . . . . . . . . . . . PP5000P
Pruner . . . . . . . . . . . . . . . . . . . . PP5500P
10
WARNING: Always stop unit anddis-
connect spark plug before removing or instal-
ling attachments.
REMOVING TRIMMER ATTACH-
MENT (OR OTHER OPTIONAL
ATTACHMENTS)
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Locking/Release
Button in Primary Hole
Coup
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
Attachment
SEN
Knob
OPERATING POSITION
ALWAYS WEAR:
Hearing
Protection
Eye Protection
Heavy,
Long Pants
TIGHTEN
2. Press and hold the locking/release button.
Locking/Release
Button
Boots
Cut from your left to your right.
Upper Shaft
Attachment
Coupler
When operating unit, clip shoulder strap onto
clamp, stand as shown and check for the fol-
lowing:
3. While securely holding the engine and
upper shaft, pull the attachment straight
out of the coupler.
S Wear hearing protection, eye protection,
head protection and heavy clothing.
S Extend your left arm and hold handlebar
grip with your left hand.
INSTALLING OPTIONAL ATTACH-
MENTS
1. Remove the shaft cap from the attach-
ment (if present).
S Hold throttle grip with your right hand with
finger on throttle trigger.
2. Position locking/release button of attach-
ment into guide recess of coupler.
3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
S Keep unit below waist level.
S Keep shoulder strap pad centered on your
left shoulder and danger sign centered on
your back.
S Maintain full weight of tool on your left
shoulder.
4. Before using theunit, tighten the knobse-
curely by turning clockwise.
S Without bending over, keep the blade or
trimmer head near and parallel to the ground
and not crowded into material being cut.
Primary Hole
Coupler
Guide Recess
OPERATING INSTRUCTIONS FOR
USE WITH TRIMMER HEAD
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head. Rocks
or debris can ricochet or be thrown into eyes
and face and cause blindness or other serious
injury.
Locking/
Release
Button
Upper
Shaft
Attachment
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit. All attachments are designed
to be used in the primary hole unless otherwise
stated in the applicable attachment instruction
manual. Using the wrong hole could lead to seri-
ous injury or damage to the unit.
Beforetrimming, bring enginetoa speedsuffi-
cient to cut material to be trimmed.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
11
Always release the throttle trigger and allow
the engine to return to idle speed when not
cutting.
Scalping
To stop engine:
S Release the throttle trigger.
S Push and release the engine ON/STOP
switch.
CUTTING METHODS
WARNING: Use minimum speed
and do not crowdthe linewhen cutting around
hard objects (rock, gravel, fence posts, etc.),
whichcan damage thetrimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
Mowing
Tip of the line
does the cutting.
Line crowded into
work area.
SWEEPING -- The fanning action of the rotat-
ing line canbe used to blow away loose debris
from an area. Keep the line parallel to and
above the area surface and swing the tool
from side to side.
Right
Wrong
S The line will easily remove grass and
weeds fromaround walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
Sweeping
S During light duty cutting.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
S For mowing or sweeping, usefull throttle for
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
OPERATING INSTRUCTIONS FOR
USE WITH WEED BLADE
S Blade Thrust is a reaction that only occurs
when using a bladed unit. This reaction can
cause serious injury such as amputation.
Carefully study this section. It is important that
you understand what causes blade thrust,
how you can reduce the chance of its
occurring, and how you can remain in control
of unit if blade thrust occurs.
Trimming
S WHAT CAUSES BLADE THRUST -- Blade
Thrust can occur when the spinning blade
contacts an object that it does not cut. This
contact causes the blade to stop for an instant
and then suddenly move or “thrust” away
from the object that was hit. The “thrusting”
reaction can be violent enough to cause the
operator to be propelled in any direction and
lose control of the unit. The uncontrolled unit
can cause serious injury if the blade contacts
the operator or others.
3 inches (8 cm)
above ground
SCALPING -- The scalping technique removes
unwanted vegetation down to the ground. Hold
the bottom of the trimmer head about 3 inches
(8 cm) above the ground and at an angle. Allow
the tip of the line to strike the ground around
trees, posts, monuments, etc. This technique in-
creases line wear.
S WHEN BLADE THRUST OCCURS --
Blade Thrust can occur without warning if
the blade snags, stalls, or binds. This is
12
more likely to occur in areas where it is
difficult to see the material being cut. By
using the unit properly, the occurrence of
blade thrust will be reduced and the
operator will be less likely to lose control.
S Do not raise the engine above your waist as
the blade can come dangerously close to
your body.
S Do not swing unit with such force that you
are in danger of losing your balance.
Bring the engine to cutting speed before enter-
ing the material to be cut.If the blade does not
turn when you squeeze the throttle trigger, make
sure shaft is fully inserted into the engine.
Always release the throttle trigger and allow
engine to return to idle speed when not cut-
ting. The blade should not turn while the en-
gine is running at idle. If the bladeturns at idle,
do not use your unit. Refer to the CARBURE-
TOR ADJUSTMENT section or contact your
authorized service dealer.
S Cut only grass, weeds, andwoody brushup
to 1/2 inch (1 cm) in diameter with the weed
blade. Do not let the blade contact material
it cannot cut such as stumps, rocks,
fences, metal, etc., or clusters of hard,
woody brush having a diameter greater
than 1/2 inch (1 cm).
S Maintain good firm footing while using the
unit. Do this by planting feet firmly in a
comfortable apart position.
S Keep the blade sharp. A dull blade is more
likely to snag and thrust.
S Cut while swinging the upper part of your
body from left to right.
S Cut only at full throttle. The blade will have
maximum cutting power and is less likely to
bind or stall.
S As you move forward to the next area to cut,
be sure to maintain your balance and footing.
S “Feed” the blade deliberately and not too
rapidly. The blade can thrust away if it is fed
too rapidly.
RECOMMENDED CUTTING POSITION
2 o’clock
S Cut only from your left to your right. Cutting on
right side of the shield will throw debris away
from the operator.
Cut using the 2
o’clock to 4 o’clock
position of the
blade
4 o’clock
S Use the shoulder strap and keep a firm grip
on the unit with both hands. A properly
adjusted shoulder strap will support the
weight of the unit, freeing your arms and
hands to control and guide the cutting motion.
S Keep feet comfortably spread apart and
braced for a possible sudden, rapid thrust of
unit. Do not overreach. Keep firm footing and
balance.
WARNING: The operator or others
must not try to clear away cut material withthe
engine running or the blade turning to avoid
serious injury. Stop engine and blade before
removing materials wrapped around blade or
shaft.
S Keep blade below waist level; it will be
easier to maintain control of unit.
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
WARNING: For each optional at-
WARNING: Blade rotates momen-
tarily after the trigger is released or engine is
turned off. The blade can seriously cut you or
others. Allow blade to stop before removing it
from the cut.
tachment used, read entire instruction manu-
al before use and follow all warnings and in-
structions in manual and on attachment.
WARNING: Ensure handlebar re-
mains installed on upper shaft (engine end of
unit) at all times.
S Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way. Replace parts that are cracked,
chipped, or damaged before using the unit.
S Do not attempt to remove cut material nor
hold material to be cut when the engine is
running or when cutting blade is moving.
S Always keep the wheel and depth adjusting
skid in contact with the ground.
EDGER SAFETY
WARNING: Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
13
S Always push the unit slowly over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
BLOWER/VACUUM SAFETY
S Never operate the cultivator without the tine
cover in place and properly secured.
S Keep the tines and guard clear of debris.
S After striking a foreign object, stop the
engine, disconnect the spark plug and
inspect the cultivator for damage. Repair
before restarting.
S Disconnect attachment from the drive engine
before cleaning the tines with a hose and
water to remove any build--up. Oil the tines to
prevent rust.
S Always wear gloves when servicing or
cleaning the tines. The tines become very
sharp from use.
S Do not run unit at high speed unless
cultivating.
WARNING:
Inspect area before
starting unit. Remove all debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S Do not set unit on any surface except a clean,
hard area while engine is running. Debris
such as gravel, sand, dust, grass, etc., could
be picked up by the air intake and thrown out
through discharge opening, damaging unit,
property, or causing serious injury to
bystanders or operator.
HEDGE TRIMMER SAFETY
S Never place objects inside the blower tubes,
vacuum tubes or blower outlet. Always direct
the blowing debris away from people,
animals, glass, and solid objects such as
trees, automobiles, walls, etc. The force of air
can cause rocks, dirt, or sticks to be thrown or
to ricochet which can hurt people or animals,
break glass, or cause other damage.
S Never run unit without the proper
equipment attached. When using your unit
as a blower, always install blower tubes.
S Check air intake opening, blower tubes or
vacuum tubes frequently, always with
DANGER: RISK OF CUT; KEEP
HANDS AWAY FROM BLADE -- Blade moves
momentarily after the trigger is released or the
engine is turned off. Do not attempt to clear
away cut material when the blade is in motion.
Make sure engine is stopped, the spark plug
wire is disconnected, and the blade has stopped
moving before removing jammed material from
the cutting blade. Do not grab or hold the unit by
the cutting blade.
engine stopped
and
spark plug
disconnected. Keep vents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
S Never place any object in air intake opening
as this could restrict proper air flow and cause
damage to the unit.
S Never use for spreading chemicals, fertilizers,
or other substances which may contain toxic
materials.
S To avoid spreading fire, do not use near leaf or
brush fires, fireplaces, barbecue pits,
ashtrays, etc.
WARNING: Inspect the area before
starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
CULTIVATOR SAFETY
WARNING: Rotating tines can cause
serious injury. Keep away from rotating tines.
Stop the engine and disconnect the spark plug
before unclogging tines or making repairs.
S Do not use a cutting blade that is bent,
warped, cracked, broken or damaged in any
other way. Have worn or damaged parts
replaced by an authorized service dealer.
S Always keep unit in front of your body.
Keep all parts of your body away from the
cutting blade.
S Keep the cutting blade and air vents clear of
debris.
POLE PRUNER SAFETY
WARNING: The reciprocating blade/
rotating chain can cause severe injury. In-
spect the unit before use. Do not operate unit
with a bent, cracked or dull bladeor dull chain.
Keep away from the blade/chain.
WARNING: Inspect the area to be
cultivated before starting the unit. Removeall
debris and hard and sharp objects such as
rocks, vines, branches, rope, string, etc.
S Avoid heavy contact with solid objects that
might stop the tines. If heavy contact
occurs, stop the engine and inspect the unit
for damage.
WARNING: The reciprocating blade/
rotating chain is sharp. Do not touch. To pre-
vent serious injury, always stop engine and
ensure blade/chain has stopped moving, dis-
connect spark plug, and wear gloves when
changing or handling the blade or chain.
14
WARNING: A coasting blade/rotat-
ing chaincancauseinjury while it continues to
move after the engine is stopped. Maintain
proper control of the unit until the blade/chain
has completely stopped moving. Keep
hands, face and feet at a distance from all
moving parts. Do not attempt to touch or stop
the blade or chain when it is moving.
WARNING: Never lean over dis-
charge chute. Rocks or debris could be
thrown into the eyes and face and cause seri-
ous injury or blindness.
WARNING: Inspect the area where
the unit is to be used. Remove objects that
could be thrown or damage the unit. Some
objects may be hidden by fallen snow -- be
alert for the possibility.
WARNING:
Falling objects can
S Direct material discharge away from glass
enclosures, automobiles, etc.
cause severe head injury. Wear head protec-
tion when operating this unit with a pole prun-
er attachment.
S Do not run engine at high speed while not
removing snow.
S Be attentive when using the snowthrower,
and stay alert for holes in the terrain and other
hidden hazards.
S Make sure the rotor will spin freely before
attaching the snowthrower to the powerhead.
S If the rotor will not rotate freely due tofrozen
ice, thaw the unit before thoroughly before
attempting to operate under power.
S Keep the rotor clear of debris.
WARNING: To prevent serious injury,
do not use more than one boom extension with
a pole pruner attachment.
S Do not throw snow near other people. The
snow thrower could propel small objects at
high speed causing injury.
WARNING: Keep the pruner away
from power lines or electrical wires.
S After striking a foreign object, stop the
engine, disconnect spark plug and inspect
the snowthrower for damage and repair if
necessary before restarting unit.
S Never operate the snowthrower near glass
enclosures, automobiles and trucks.
S Never attempt to use the snowthrower on a
roof.
S Never operate the snowthrower near
window wells, dropoffs, etc.
S Never discharge snow onto public roads or
near moving traffic.
S Clear snow from slopes by going up and
down; never across. Use caution when
changing directions. Never clear snow
from steep slopes.
S Let snowthrower run for a few minutes after
clearing snow so moving parts do not
freeze.
S Only use for pruning limbs or branches up
to 4 inches (10 cm) in diameter.
S Do not operate the unit faster than the
speed needed to prune. Do not run the unit
at high speed when not pruning.
S Always stop the unit when work is delayed
or when walking from onecutting location to
another.
S If you strike or become entangled with a
foreign object, stop the engine immediately
and check for damage. Have any damage
repaired by an authorized service dealer
before attempting further operations.
Discard blades that are bent, warped,
cracked or broken.
S Stop the unit immediately if you feel excessive
vibration. Vibration is a sign of trouble. Inspect
thoroughly for loose nuts, bolts or damage
before continuing. Contact an authorized
service dealer for repair or replacement of
affected parts as necessary.
S Look behind and use care when backing up.
Exercise caution to avoid slipping or falling,
especially when operating in reverse.
S Know how to stop quickly.
SNOW THROWER SAFETY
WARNING: Keep hands and feet
away from the rotor when starting or running
the engine. Never attempt to clear the rotor
with the engine/motor running. Stop engine
and disconnect spark plug before unclogging
snow or debris from discharge chute or when
adjusting vanes.
15
MAINTENANCE
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove parts by pressing button to re-
lease air filter cover.
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
ommended maintenance
3. Wash the filter in soap and water.
4. Allow filter to dry.
described in the instruction
manual performed by an
5. Replace parts.
authorized service dealer.
Button
If any dealer other than an authorized
service dealer performs work on the
product, Poulan PRO may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
Air Filter
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
ir Filter Cover
S Air Filter
S Housing Screws
S Assist Handle Screw
S Debris Shield
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
CHECK FOR DAMAGED OR
WORN PARTS
WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen and
must be removed to avoid creating a fire haz-
ard or affecting engine performance.
For normal homeowner use, the muffler and
spark arresting screen will not require any
service. After 50 hours of use, we recom-
mend that your muffler be serviced or re-
placed by an authorized service dealer.
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/STOP Switch -- Ensure ON/STOP
switch functions properly by pushing and
releasing the switch. Make sure engine
stops. Wait 5 seconds before attempting to
restart unit to allow switch to reset. Restart
engine and continue.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch (0.6 mm). Igni-
tion timing is fixed and nonadjustable.
NOTE: This spark ignition system complies
with the Canadian standard ICES--002.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and
discard.
INSPECT AND CLEAN UNIT AND DE-
CALS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a milddeter-
gent.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench.
4. Reinstall the spark plug boot.
16
SERVICE AND ADJUSTMENTS
REPLACING THE LINE
CARBURETOR IDLE SPEED
For unit to operate properly, the cutting line
should be replaced when line becomes worn to
less than 3 inches (7.5 cm) in length from the
edge of the line exit tunnels on each side of the
cutting head.
ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The trimmer
head, blade or any optional attachment will be
spinning during most of this procedure. Wear
your protective equipment and observe all safe-
ty precautions. After making adjustments, the
trimmer head, blade or any optional attachment
must not move/spin at idle speed.
The carburetor has been carefully set at the
factory. Adjustments may benecessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is
released.
S The trimmer head, blade or optional
attachment moves/spins at idle.
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
1. Remove and discard worn line before
installing new line.
2. Use only 0.115 inch (3 mm) diameter
Poulan PRO brand cut length line.
3. Insert one end of the line through the
positioning tunnel.
4. Continue to feed line through tunnel until
line is centered (leaving equal amounts
on each side). See illustration below.
Positioning
tunnel
To adjust idle speed:
Allow engine to idle. Adjust speed until engine
runs without trimmer head, blade or optional
attachment moving or spinning (idle too fast)
or stalling (idle speed too slow).
S Turn idle speed screw clockwise to
increase engine speed if engine stalls or
dies.
S Turn idle speed screw counterclockwise to
decrease engine speed if trimmer head,
blade or optional attachment moves or
spins at idle.
5. Insert ends of line one at a time through
the line exit tunnels.
6. Pull the line and make sure the line is ex-
tended fully through the tunnels.
Line exit
Line exit
tunnel
tunnel
WARNING: Recheck the idle speed
after each adjustment. The trimmer head,
blade or optional attachment must not move
or spin at idle speed to avoid serious injury to
the operator or others.
7. Correctly installed line will be the same
length on both ends.
BLADE REPLACEMENT
Refer to the ASSEMBLY section for blade re-
placement instructions and illustrations.
If you require further assistanceor are unsure
about performing this procedure, contact an
authorized
service
dealer
or
call
1--800--554--6723.
17
STORAGE
HELPFUL TIP
WARNING: Perform the following
During storage of your gas/
oil mixture, the oil will sepa-
rate from the gas.
steps after each use:
S Allow engine to cool before storing or trans-
porting.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy
storage.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
18
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Carburetor requires
adjustment.
5. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
1. See “Carburetor Idle Speed Adjustment”
in Service and Adjustments Section.
2. Crankshaft seals worn. 2. Contact an authorized service dealer.
3. Compression low.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Fuel mixture incorrect. 1. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
2. Air filter dirty.
3. Carburetor requires
adjustment.
2. Clean or replace air filter.
3. Contact an authorized service dealer.
1. Fuel mixture incorrect.
1. See “Fueling Engine” in Operation
section.
Engine runs
hot.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
19
LIMITED WARRANTY
Poulan PRO, a division of Husqvarna Consum-
In Canada, contact:
er Outdoor Products N.A., Inc., warrants to the
original consumer purchaser that each new
Poulan PRO brand gasoline tool or attachment
is free from defects in material and workman-
ship and agrees to repair or replace under this
warranty any defective gasoline product or at-
tachment as follows from the original date of
purchase.
Poulan PRO
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTH-
ER RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIM-
ITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by Poulan PRO for
this tool. This warranty does not cover tune--up,
spark plugs, filters, starter ropes, cutting line, or
rotating head parts that will wear and require re-
placement with reasonable use during the war-
ranty period. This warranty does not cover pre--
delivery setup or normal adjustments explained
in the instruction manual. This warranty does
not cover transportation costs.
The policy of Poulan PRO is to continuously
improve its products. Therefore, Poulan
PRO reserves the right to change, modify, or
discontinue models, designs, specifications,
and accessories of all products at any time
without notice or obligation to any purchaser.
In the event you have a claim under this warran-
ty, you must return the product to an authorized
service dealer.
Should you have any unanswered questions
concerning this warranty, please contact:
Poulan PRO, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1--800--554--6723
U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency, California Air Resources
Board, Environment Canada and Poulan
PRO are pleased to explain the emissions con-
trol system warranty on your year 2010 and lat-
er small off--road engine. In California, all small
off--road engines must be designed, built, and
equipped to meet the State’s stringent anti--
smog standards. Poulan PRO must warrant
the emission control system on your small
off--road engine for the periods of time listed
below provided there has been no abuse, ne-
glect, or improper maintenance of your small
off--road engine. Your emission control system
includes parts such as the carburetor, the igni-
tion system and the fuel tank. Where a warrant-
able condition exists, Poulan PRO will repair
your small off--road engine at no cost to you.
Expenses covered under warranty include
diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE: If any emissions related part on your
engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of such an emission related
part, the part will be repaired or replaced by
Poulan PRO. OWNER’S WARRANTY RE-
SPONSIBILITIES: As the small off--road en-
gine owner, you are responsible for the per-
formance of the required maintenance listed
in your instruction manual. Poulan PRO rec-
ommends that you retain all receipts covering
maintenance on your small off--road engine,
but Poulan PRO cannot deny warranty solely
for the lack of receipts or for your failure to en-
sure the performance of all scheduled main-
tenance. As the small off--road engine owner,
you should be aware that Poulan PRO may
deny you warranty coverage if your small off--
road engine or a part of it has failed due to
20
abuse, neglect, improper maintenance, un-
approved modifications, or the use of parts
not made or approved by the original equip-
ment manufacturer. You are responsible for
presenting your small off--road engine to an
Poulan PRO authorized repair center as soon
as a problem exists. Warranty repairs should be
completed in a reasonable amount of time, not
to exceed 30 days. If you have any questions
regarding your warranty rights and responsibili-
ties, you should contact your nearest authorized
service center, call Poulan PRO at
1--800--554--6723, or send e-mail correspond-
ence to emission.warranty@HCOP--emission.
the determination that a warranted part is de-
fective if the diagnostic work is performed at
an approved Poulan PRO servicing center.
CONSEQUENTIAL DAMAGES: Poulan
PRO may be liable for damages to other en-
gine components caused by the failure of a
warranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD -ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty
claim. Poulan PRO is not liable to cover failures
of warranted parts caused by the use of add--on
or modified parts. HOW TO FILE A CLAIM: If
you have any questions regarding your warran-
ty rights and responsibilities, you should contact
your nearest authorized service center, call
Poulan PRO at 1--800--554--6723, or send
e-mail correspondence to emission.warranty
@HCOP--emission.com. WHERE TO GET
WARRANTY SERVICE: Warranty services
or repairs shall be provided at all Poulan PRO
service centers. Call: 1--800--554--6723 or
send e-mail correspondence to emission.
warranty@HCOP--emission.com. MAINTE-
NANCE, REPLACEMENT AND REPAIR
OF EMISSION RELATED PARTS: Any Pou-
lan PRO approved replacement part used in
the performance of any warranty mainte-
nance or repair on emission related parts will
be provided without charge to the owner if the
part is under warranty. EMISSION CON-
TROL WARRANTY PARTS LIST: Carbure-
tor, air filter (covered up to maintenance sched-
ule), ignition system: spark plug (covered up to
maintenance schedule), ignition module, muffler
including catalyst (if equipped), fuel tank.
MAINTENANCE STATEMENT:The owner is
responsible for the performance of all re-
quired maintenance as defined in the instruc-
tion manual.
com.
WARRANTY
COMMENCEMENT
DATE: The warranty period begins on the date
the small off--road engine is purchased.
LENGTH OF COVERAGE: This warranty
shall be for a period of two years from the ini-
tial date of purchase, or until the end of the
product warranty (whichever is longer).
WHAT IS COVERED: REPAIR OR RE-
PLACEMENT OF PARTS. Repair or replace-
ment of any warranted part will be performed
at no charge to the owner at an approved
Poulan PRO servicing center. If you have any
questions regarding your warranty rights and
responsibilities, you should contact your
nearest authorized service center, call Pou-
lan PRO at 1--800--554--6723, or send e-mail
correspondence to emission.warranty@
HCOP--emission.com. WARRANTY PERIOD:
Any warranted part which is not scheduled for
replacement as required maintenance, or
which is scheduled only for regular inspection
to the effect of “repair or replace as neces-
sary” shall be warranted for 2 years. Any war-
ranted part which is scheduled for replace-
ment as required maintenance shall be
warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
21
|