Precision Power Car Speaker 355cs User Manual

Component Speakers

355cs 356cs

introduction

™

Thank you for choosing PrecisionPower automotive component loudspeakers

These reference quality speakers combine the acoustic excellence achieved from

25 years of loudspeaker research and development, with innovative and timeless

industrial design, and cutting edge material choices Tuned for precise reproduction

of the supplied musical signal, they accurately deliver every nuance and detail

™

while retaining the classic "PrecisionPower sound" that has enchanted multiple

generations of owners With a minimum of care, this high performance component

speaker system will deliver years of trouble-free satisfaction

about this manual

™

To achieve optimum performance from your PrecisionPower automotive

component loudspeakers, we recommend that you read this manual thoroughly

before installation and use For the best results and support, please consult

™

with your local authorized PrecisionPower retailer Technical support is also

™

available from PrecisionPower

at 1-800-753-0800 selection 3 Keep this

manual in a safe place for future reference

features

Molded woofer basket - The backbone of any good woofer is its basket It provides

the proper alignment and support structure for the magnet and moving parts while

the very thin braces guarantee a minimum of early reflections off the basket that

would be ordinarily transmitted as sonic colorations through the cone

Woofer cone - Interlaced Aramid Fiber (Kevlar) with Mica and fiberglass mixture

in a IMPP (Injection Molded Poly Propylene) base, cones provide the perfect

combination of rigidity and low moving mass for ultra-low distortion and superior

transient response

Vented voice coil - Magnet cooling vent construction enhances power handling

capabilities of the woofer The voice coil is made using copper clad aluminum wire

to minimize weight and increase efficiency and low frequency response

Extended center pole - Woofer magnet geometry provides a symmetrical magnetic

pattern to reduce THD

Tweeter - Ultra-light silk dome design is treated with polymer compound to control all

non-linear resonances

Multi-mount tweeter - The following mounting options (surface, angled surface,

flush, or angled flush) are supplied to mount the ferrofluid cooled neodymium

tweeter

ꢁ

Tweeter level control - A three-position switch adjusts the volume of the tweeter

with respect to the midrange

Tweeter phase switch - A two-position switch which allows 180° or 0° phase

difference between the tweeters and midranges

Midrange contour control - A two-position switch offers a frequency response

correction circuit to adjust for flat frequency response in the car on axis or off

axis

Bi-amplifiable/ bi-wirable - The passive crossover supplied with this system is bi-

amplifiable or bi-wirable; typically only available in high quality audiophile home

loudspeakers

Solid state tweeter protection - Advanced protection circuitry provides protection

for the tweeter against overpowering or amplifier clipping

ꢂ

cautions

Study your automobile thoroughly before you drill or cut any holes Take extra care

when working near gas tanks, gas lines, brake or hydraulic lines and electrical

wiring

Wear eye and ear protection when using power tools Keep the woofers and

tweeters away from metal filings and shavings Once foreign objects are stuck to

the magnets or tweeter dome, it will be virtually impossible to remove them Keep

the tweeters in their protective bags until final mounting to prevent any possibility

of metal dust or chips from passing through the grille and accumulating on the

dome

Exercise caution when working with the cs series with the grille removed A slip of

the hand with a screwdriver or other tool can result in irreparable damage to the

cone or dome Do not touch the cone or dome

Do not install the components where they will be subject to excessive heat,

moisture or dust, or where they will be kicked or repeatedly bumped or brushed

Make absolutely sure that the woofer is connected to the lowpass output and the

tweeter is connected to the highpass output of the crossover network If these

connections are reversed, low-frequency signals will be fed to the tweeter without

fuse protection In this case, the tweeter may be damaged, such damage is not

covered by the warranty

When removing or installing the grills be careful not to brush the woofer's rubber

surround or the tweeter's dome with the edge of the grille Cutting or tearing the

surround or dome will destroy the unit

Never run wires outside or beneath the vehicle where they can be snagged by

road hazards or the moving parts of the vehicle Use existing wire channels,

sills, panels and molding strips inside the automobile to hide the wiring for neat

appearance and safety

Make sure your radio/cassette/cd player and or other equipment is turned off

while connecting the speaker terminals Turn on the various components and

slowly advance the volume control ONLY after checking and double checking all

connections

NOTE: If the sound is weak or distorted, immediately turn down the volume and

see the section entitled Troubleshooting

ꢃ

installation planning

Proper installation planning is the best way to maximize performance By planning

your installation carefully you can avoid situations where the performance or

™

reliability of your system is compromised Your authorized PrecisionPower

™

dealer or PrecisionPower audio technical support at 1-800-753-0800 selection

3 has been trained to know how to maximize your speakers sonic potential They

are a valuable resource in helping you with your system design and installation

amplifier requirements

This speaker system requires a minimum of 45 watts per channel to achieve

reasonable listening volumes in a moving automobile without clipping the amplifier

™

PrecisionPower

recommends no more than 150 watts per channel as a

maximum so as not to exceed the thermal or mechanical limitations of the speaker

system Any amplifier between 45 watts and 150 watts may be used If you choose

to use an amplifier with more than 150 watts use caution as speaker damage may

™

occur at high volume settings All PrecisionPower loudspeakers will produce

reasonable volume levels in the automotive environment using moderate amplifier

power However, the use of a low powered amplifier to try and attain very high

volume levels can lead to overdriving the amplifier and damaging the speaker

system As a rule, do not turn the volume up above the point where you hear

distortion on musical peaks from either an overdriven amplifier or mechanical

noise from an overstressed speaker For the best performance and reliability;

select an amplifier with slightly more than the maximum power you are likely to

need to generate the desired volume levels This margin of reserve power will

ensure that the amplifier will not be routinely driven beyond its design limits

WArNINg: Excessive sound pressure level can permanently damage your

™

hearing The maximum volume levels attainable with PrecisionPower speakers,

combined with high-power amplification, may exceed safe levels of extended

listening

mounting locations

There are many possible choices of mounting locations The vehicle factory

locations will usually dictate the woofer mounting position Because of its small

size and multiple mounting options, the tweeter can go virtually anywhere

™

PrecisionPower

uses an unusually low crossover frequency for the tweeter

which means you are not restricted to mounting the tweeter close to the midrange

speaker The tweeter can be mounted as far as 24" (60 cm) from the midrange

speaker without causing adverse effects on the sound quality However, better

results are usually obtained by locating the tweeters and midranges relatively

close to each other, and by keeping the sound path lengths between the listener

and the left and right speakers as equal as possible

™

PrecisionPower

cannot recommend specific tweeter mounting locations for

each vehicle, but in general try to keep the tweeters as far to the sides of the car

as practical Avoid placing them above ear level unless the woofers are also above

ꢄ

ear level Place the tweeters in similar locations on both sides of the vehicle Try

a few locations by just placing the tweeter or taping it in a location and listening

to ensure the desired stereo image and high frequency dispersion are achieved

before committing to a location by drilling holes in the vehicle You should also

experiment with the tweeter phase switch settings to find the most effective

combination of location and phase

ꢅ

specifications

355cs

356cs

Frequency response

Sensitivity

77Hz -22kHz

86db

60Hz -22kHz

87db

Impedance

4 ohms

60/120

recommended ampliﬁer 50/100

power

Mounting depth (woofer) 2 5

(in)

2 5

77 28 Hz

3 40 ohms

6 24

65 96 Hz

3 40 ohms

5 91

Qms

Qes

Qts

0 64

0 65

0 58

Vas (L)

Mms (Kg)

Cms

3 57

7 38

012

013

298

437

6 22

5 38

Xmax

11328

ꢆ

crossover features and connections

Tweeter

DC Clip

Protection

Tweeter

Thermal

Breaker

Midrange

Contour Switch

Tweeter

Phase Switch

Parallel Bi-amp

Switch

Tweeter Level

Switch

Woofer Tweeter

OUT

Woofer Tweeter

demo car

180°

0°

-3 +3

Midrange contour switch

Positions of Demo or Car are provided to offer different contours to midrange

woofer frequency response This switch should be left in the Car position for most

applications

bi-amp/parallel switch

Select the Bi-amp position if you intend on driving the woofers and tweeters with

separate amplifiers (four channels) Select the Parallel position if you intend on

driving the woofers and tweeters with the same amplifier (two channels)

tweeter level switch

The three-position switch in the crossover box adjusts the output level of the

tweeter The mid-position (0) is referenced as equal output from the midrange

speaker and the tweeter The high position (+3) provides 3dB more output from

the tweeter The low position (-3) provides 3dB less output from the tweeter Select

the position of this switch for your listening preference

tweeter phase switch

Select 0 or 180 degrees phase relationship between the tweeters Select the

position of this switch for your listening preference

tweeter thermal breaker

This component protects the tweeter speaker if too much power is delivered to the

tweeter If activated the tweeter will briefly stop producing sound until the breaker

ꢇ

automatically resets.

Tweeter DC Clip Protector

These components limit the amount of current delivered to the tweeter if they are

overdriven by either excess amplification or clipped signal from an overdriven

amplifier

connections to the amplifier

The crossovers are supplied with a removable screw type connector The

crossover has two sets of input terminals, this allows the system to be driven by

either two or four channels of amplification To correctly use these wiring schemes

you must move the Bi-amp/Parallel switch to the desired position

To bi-amplify the system you will need two stereo amplifiers (or 4 amplifier

channels) with one pair of channels to drive the tweeters and one pair to drive

the woofers

You may also Bi-wire the system by connecting the woofer input terminals to the

amplifier and connecting the woofer input terminals to the same amplifier with

another set of speaker wires This is sometimes done to allow a specific high

frequency or low frequency cabling to be used for the two separate signal paths

See Crossover Installation for additional information on bi-wiring

Be sure to connect the positive crossover terminals to the positive speaker

terminals and positive amplifier terminals, also ensure that the negative crossover

terminals connect to the negative amplifier and speaker terminals Once all of the

wires are attached to the connector and the crossover is mounted, the connector

can be plugged into its mating receptacle on the crossover

speaKer WirinG

speaker wire selection

Use insulated two-conductor stranded wire to connect the crossover to the

speakers and amplifier The size of the wire can have an audible effect of the

performance of the system Stranded 18 gauge "zip cord" will work, but can result

in lower output or unpredictable frequency response For wire runs of 50 feet (15

m) or less, we recommend 16 gauge or larger wire The crossover connector will

accept up to 14 gauge wire

polarity and phasing

The polarity of the positive/negative orientation of the connections for every

speaker and amplifier connection must be consistent so all the speakers will be

in phase When the polarity of one connection is reversed, bass output may be

reduced or stereo imaging degraded Most speaker wire is marked so you can

identify the two conductors There may be ribs or a stripe on the insulation of one

conductor, or the wire may have clear insulation with different color conductors

(copper and silver) There may also be polarity indications printed on the

insulation Identify the positive and negative conductors and be consistent with

every speaker and amplifier connection The supplied speaker wire has a white

stripe to indicate the (+) positive conductor

termination

The woofer uses an angled locking screw connection integrated to the basket of

the speaker The tweeter wires are terminated with molded connectors (male and

female) Use the supplied wire with insulated connectors to extend the tweeter

wires to the crossover section Alternatively you may solder the tweeter wire

connections and insulate them with high quality heat shrink tubing

speaKer installation

Woofer installation

The woofer will fit into many standard factory mounting locations using the

existing mounting holes in the automobile remove the trim panels and inspect

the installation locations before you cut and drill the holes required to mount the

woofer removing the panel will also make it much easier to route wiring inside

the door Look for original equipment speaker installation cutouts that can be used

to install the woofers with little or no modifications Use the supplied template to

help you locate and mark the holes needed to install the speakers

If the planned installation location is in a door panel, be sure the speaker will not

interfere with the window lowering mechanism Ensure that the speaker wires are

positioned to clear all moving parts inside the door

For each woofer you will need to cut one large hole and drill small holes around

the circumference If the mounting surface is covered by carpet or fabric, use a

knife or razor to cut the material away from the holes to be cut This prevents

material or fibers from becoming tangled in the drill bit or cutting blade If you

are using the packaged metal screws provided in the hardware kit, drill the four

speaker mounting screw holes with a 1/8"(3 mm) drill

Clean the work areas of all filings and shavings with a vacuum cleaner before you

proceed with woofer mounting

Woofer mounting

route the speaker wire from the woofer installation locations to the crossovers

Pull the wire through the installation hole and attach the terminals on the ends

to terminals connections on the speakers refer to the speaker wiring section of

this manual and the wiring diagrams Push the wire back into the area behind

the installation location and be sure it will not interfere with the speaker or get

snagged by any mechanisms in the area

Attach the supplied foam gasket strip to the mounting surface of the speaker

This will ensure an air tight seal, which is required to achieve the best bass

performance

Install the speakers by gradually tightening each mounting screw Tighten the

screws until the speaker is well seated, but take care not to over-tighten

tWeeter installation

The speaker system is supplied with five different tweeter mounting options:

coaxial, surface, surface angle, flush, and angled flush mount After you have

decided which option is best suited to your installation, refer to the following

sections for specific details on mounting the tweeter

coaxial mount

These components have the unique ability to also be used as a coaxial speaker

in specific applications This allows the tweeter to be placed directly in the center

of the woofer without obstructing the voice coil or the function of the woofer

CAUTION: Use caution to not damage the speaker cone in the procedure

described in the next steps

Unscrew and remove the center bullet from the threaded mounting post by turning

the bullet counterclockwise as shown in the following illustration retain the bullet

for future use

Threaded mounting

post

Turn bullet nose

counterclockwise

Install the tweeter into the extension housing by first threading the tweeter wires

through the extension housing and then installing the tweeter into the mounting

slots of the housing and turn the tweeter counterclockwise to lock the tweeter in

place

1ꢀ

Coaxial

Extension

Tweeter

Speaker

Wires

Mounting

Slots (qty 4)

Mounting

Tabs (qty 4)

CAUTION: Do NOT overtighten the tweeter assembly

Now feed the tweeter speaker wires through the front center of the woofer (where

the aluminum bullet was removed) As shown in the next illustration Align and

thread the coaxial tweeter assembly on the threaded post in the center of the

woofer rotate the coaxial tweeter assembly clockwise until snug Connect the

tweeter wires to the tweeter output from the crossover

Threaded mounting

post

Turn tweeter

coaxial mount

assembly

clockwise

The tweeter is mounted at and angled relative to the woofer Before final woofer

mounting, rotate the woofer so that the tweeter is pointed in the desired direction,

typically towards the listener's ear location

surface mount (Straight or Angled)

The preparation of the mounting surface for the tweeter involves drilling three

holes Two holes are for the mounting screws Their centers must be spaced15/16”

1ꢁ

(24 mm) apart Use a 1/8" (3 mm) drill bit for the supplied screws to mount the cup

The third 1/4” (7 mm) hole is required for the wire to pass through

Use the template provided to locate the hole centers Cut carpeting or fabric away

from the hole locations to prevent tangling of fibers in the drill bit

surface mount (Straight or Angled)

Insert two #6 x 3/4" flat head sheet metal

screws through the holes in the bottom of

the surface mount cup Screw the cup in

Mounting slots (qty 4)

place Ensure the mounting screws are

driven in straight, so the heads sit flush on

the cup mounting surface This ensures the

tweeter will seat properly in the surface

mounting cup The tweeter is then slid into

#6 x 3/4" screws

(qty 2)

the mounting cup (tabs aligned with the

mounting slots), and turned counterclockwise

to lock in place

NOTE: The mounting cup is also supplied with an angled surface mounting cup

(not shown) This allows the tweeter to be mounted at an optimum acoustic angle

for the listener Follow the same procedure as above to mount and assemble the

tweeter in this housing

Flush mount (Surface or Angled)

NOTE: Ensure that there is enough clearance within the interior door panel for the

M4-0 7 X 4-1/2 cm (1 77 inches) flat head mounting screws reduce the length of

the mounting screw as necessary to meet clearance

Metal mounting bracket

Check the intended installation site

to be sure that there is sufficient

depth behind the mounting surface

for the rear cup and mounting screws

Mounting slots (qty 4)

The minimum depth required behind

the back of the mounting surface is

1" (25 mm) The front cup mounts

into the mounting through a 1-7/8"

M4-0.7 x 4-1/2 cm

screws (qty 2)

(48 mm) diameter hole Be careful

that the hole does not exceed 2-1/8"

(55 mm) diameter at any point so

Flush Angled

Mounting Cup

that the rim of the cup will completely

cover the edge of the hole

Use the template provided to locate the hole centers Cut carpeting or fabric away

1ꢂ

from the hole locations to prevent tangling of fibers in the saw blade

Insert the two M4-0 7 X 4-1/2 cm (1 77 inches) flat head metal screws through the

mounting holes and just start the threads into the metal mounting bracket With

the metal bracket attached to the mounting cup slide one end of the metal bracket

and then the other end into the mounting hole Hold the mounting cup in its final

position and tighten, but do not over tighten the two mounting screws

The tweeter is then slid into the mounting cup (tabs aligned with the mounting

slots), and turned counterclockwise to lock in place

NOTE: The mounting cup is also supplied with an angled surface mounting cup

(not shown) This allows the tweeter to be mounted at an optimum acoustic angle

for the listener Follow the same procedure as above to mount and assemble the

tweeter in this housing

tweeter mounting

route the wire from the crossover locations to the tweeter locations Pull the wire

through the wire hole and attach crossover wires to the wires from the tweeters

Connect the positive wire to the positive (+) terminal of the tweeter, which is

marked with the white trace See the information in the speaker wiring section

of this manual and the wiring diagrams Push the wire back into the area behind

the installation location and be sure it will not interfere with the speaker or with

anything behind the mounting panel To attach the tweeter to the surface or flush

mount assembly, align the tabs in the mounting cup with the relieved areas in the

tweeter mount

Mounting

Screws

Surface Mount Housing

TWEETER

Tweeter

Wiring

Panel

Wiring

1ꢃ

Tweeter

Bolts

Panel

Bracket

Tweeter

Wire

Flush Mount

Housing

Wiring

NOTE: The tweeter grill can be easily removed for coaxial applications, or to

facilitate mounting the tweeter behind an existing factory grill Use the supplied

black butyl material to attach the tweeter grill for all other applications

1ꢄ

crossover installation

The system supports conventional wiring, Bi-wiring or Bi-amping using the

supplied passive crossovers While conventional (parallel mode) wiring will provide

excellent sound, bi-wiring or bi-amping may further enhance the performance in

no-compromise systems

Bi-wiring uses a separate pair of speaker wires for the high frequency and low

frequency signal between an amplifier channel and its associated crossover

network This gives you the option of choosing wire which may have slightly

different sonic characteristics in order to optimize performance of each frequency

range Also, it reduces the overall wiring resistance between the crossover and

amplifier, much like the use of larger gauge wire This option provides the most

benefit when the crossover network is mounted a long distance away from the

amplifier If the crossover is mounted close to the amplifier it is doubtful that there

will be an appreciable difference between bi-wiring and conventional wiring

Bi-amping uses a separate amplifier channel for the high-frequency and low-

frequency sections, instead of the single amplifier channel used in conventional

and bi-wired connections Bi-amping provides the additional advantage of allowing

use of the amplifier's level controls to provide an additional level of fine-tuning not

possible with the tweeter-level switch alone In addition, at high power levels, a

bi-amplified connection can help protect the tweeter from amplifier clipping, which

is more likely to occur on channels driving the midrange When bi-amping using

the passive crossovers, the midrange low-pass filter and tweeter high-pass filter

on the amplifier or external active crossover should be bypassed

Carefully route the wires from the woofer and tweeter to the crossover mounting

location The crossover installation location should be reasonably accessible to

allow easy connection of the wires and adjustment of the internal switches If the

crossover must be mounted in an inaccessible location make the speaker wire

connections and adjustments before final installation Be sure the installation

location has adequate clearance to allow the removal and replacement of the

cover Mounting the crossover requires removing the top cover of its housing

grasp the top cover at the front and back Compress the cover slightly in the

center and lift it off the bottom of the housing Mounting the crossover requires

four holes in a rectangular pattern 2 13/16" x 4 1/4" (7 14 cm x 10 8 cm) on a flat

surface Use the crossover as a template for drilling the mounting holes

Align the mounting holes in the bottom half of the crossover unit with the holes

you have drilled at the installation site Pass the four #6 x 1 1/4" screws through

the holes in the crossover unit, and tighten them until the assembly is firmly in

place As before, do not over-tighten; this is especially important if the mounting

surface is not perfectly flat

1ꢅ

After all the connections and any necessary adjustments have been made snap

the cover back in place

connecting the system

Trim the speaker wire as needed Strip about 1/4" (6 mm) of the insulation from

the ends Twist the exposed strands thoroughly to prevent any loose strands from

causing a short circuit You may also "tin" the wire with a soldering iron The wires

attach to a removable connector which in its assembled position has the screws

facing the bottom of the crossover Insert the prepared wire into the appropriate

location (see diagram or refer to the crossover circuit board) in the connector strip

and tighten the screws to secure the wires in place Be sure to note the polarity

marking on the circuit board

1ꢆ

crossover connections and input sWitcH settinG

route the wires connected to the input terminals on the crossover network to the

power amplifier Connect the wires to the amplifier outputs as recommended by

the manufacturer of the unit Make sure there are no stray strands of wire which

could cause a short circuit Observe left/right polarity markings

6WDQGDUG

ꢃ6ZLWFKꢀLQꢀ3DUDOOHOꢀ3RVLWLRQꢄ

7ZHHWHU

%LꢂDPSꢀ3DUDOOHO

ꢁ

ꢂ

287

ꢀ

ꢁ

ꢂ

ꢁ

7ZHHWHU

ꢂ

ꢁ

ꢂ

:RRIHU

ꢁ

&URVVRYHU

Amplifier

ꢁ

ꢂ

ꢁ

:RRIHU

ꢂ

NOTE: In this configuration, you may connect the amplifier (+) positive to either

the tweeter (+) or woofer (+) terminal, and the amplifier (-) negative to either the

tweeter (-) or woofer (-) terminal The parallel switch ensures that both halves of

the crossover are supplied with signal as least one (+) and (-) input terminal are

connected

1ꢇ

bi-aMplifier connections to crossover

Connections from the crossover to the woofer and tweeter are the same as the

normal wiring method Connect the amplifier you have chosen for the tweeter to

the “Tweeter In” terminals input Connect the woofer amplifier to the “Woofer In”

terminals

NOTE: You must move the selectable switch to the Bi-amp position Failure to set

the switch correctly may cause damage to the amplifiers or the crossover

Bi-Amplified

(Switch in Bi-amp Position)

Tweeter

OUT

Tweeter Amplifer

Tweeter

Woofer

Crossover

Woofer

Woofer Amplifer

ꢀ0

bi-Wire connections to crossover

Connections from the crossover to the woofer and tweeter are the same as the

normal wiring method Connect the amplifier to the tweeter input terminals with

one run of wire Connect the amplifier to the woofer input terminals with another

run of wire

NOTE: You must move the Bi-amp/parallel switch to the parallel position Failure

to set the switch correctly will not damage the equipment, but could interfere with

any enhancement of the sound due to bi-wiring

Bi-Wired

(Switch in Parallel Position)

Tweeter

OUT

Tweeter

Woofer

Crossover

Amplifer

Woofer

ꢀ1

troublesHootinG

symptom

probable cause

remedy

No output

Source or ampliﬁer

not turned on

Check source or ampliﬁer and ﬁx

as required

Audio input not con-

nected or no output

from source

Check rCA connection and

signal integrity, ﬁx or replace as

required

Bi-amp/parallel switch Set Bi-amp/parallel switch to

set incorrectly for ap- correct setting (see Crossover

plication

connections and input switch set-

ting, Bi-ampliﬁed connections to

crossover, or Bi-wire connections

to crossover)

Protection circuit

activated

Turn down volume, protection

circuit will automatically reset

Speaker wires not

connected

Check speaker wires and ﬁx or

replace as required

Audio cycles on

and off

Speaker damaged

Check system with known work-

ing speaker and ﬁx or replace as

required

Thermal protection

engaged

Check that ampliﬁer has ad-

equate ventilation, check speaker

impedance load

Loose or poor audio

connections

Check rCA power and speaker

connections and ﬁx or replace as

required

Distorted output

Preamp volume set

to high exceeding

maximum capability of

ampliﬁer

Check volume or preamp and

adjust appropriately

Impedance load to

ampliﬁer too low

Check speaker impedance load, if

below 1 ohm rewire the speakers

to achieve a higher impedance

Bi-amp/parallel switch Set Bi-amp/parallel switch to

set incorrectly for ap- correct setting (see Crossover

plication

connections and input switch set-

ting, Bi-ampliﬁed connections to

crossover, or Bi-wire connections

to crossover)

Shorted speaker

wires

Check speaker wire connections

and ﬁx or replace as needed

ꢀꢀ

Speaker not connect- Check speaker wring and ﬁx or

ed properly

replace as needed refer to the

speaker wiring section of this

manual for detailed instructions

Speaker damaged

Check system with known work-

ing speaker and ﬁx or replace as

required

Poor bass re-

sponse

Speakers wired with

wrong polarity

Check speaker polarity and ﬁx as

needed

Stereo/bridge switch

set to bridge position

Set switch to stereo position

Speaker connected

across wrong output

terminals

Check that the speaker wires

are not connected to the bridged

terminals and ﬁx as needed

Source set to mono

Check source and adjust controls

as needed

ꢀꢁ

ꢀꢂ

notes

________________________________________________________________

ꢀꢃ

Warranty

LIMITED ONE-YEAR CONSUMER WARRANTY/

*LIMITED TWO-YEAR CONSUMER WARRANTY FOR AUTHORIZED DIRECTED DEALER

PURCHASE & INSTALLATION

Directed Electronics (herein “Directed”) promises to the original purchaser, to repair or replace with a

new or refurbished unit (at Directed’s sole and absolute discretion) this product should it prove to be

defective in workmanship or material under normal use, for a period of *two-years from the date of

purchase from the authorized Directed dealer PROVIDED the product was purchased and installed by

an authorized Directed dealer. During this *two-year period, there will be no charge for the repair or

replacement PROVIDED the unit is returned to Directed, shipping prepaid, along with the required proof

of installation, the bill of sale or other dated proof of purchase, and the consumer’s contact information.

If the unit is installed by anyone other than an authorized Directed dealer, the warranty period will be

one-year from the date of purchase. This warranty is non-transferable and does not apply to any unit

that has been modified or used in a manner contrary to its intended purpose, and does not cover damage

to the unit caused by installation or removal of the unit. During this one-year period, there will be no

charge for the repair or replacement PROVIDED the unit is returned to Directed, shipping pre-paid,

along with the bill of sale or other dated proof of purchase and the consumer’s contact information. This

warranty is void if the product has been damaged by accident or unreasonable use, neglect, improper

service or other causes not arising out of defects in materials or construction. This warranty does not

cover the elimination of externally generated static or noise, or the correction of antenna problems or

weak reception, damage to speakers, accessories, electrical systems, cosmetic damage or damage due

to negligence, misuse, failure to follow operating instructions, accidental spills or customer applied

cleaners, damage due to environmental causes such as floods, airborne fallout, chemicals, salt, hail,

lightning or extreme temperatures, damage due to accidents, road hazards, fire, theft, loss or vandalism,

damage due to improper connection to equipment of another manufacturer, modification of existing

equipment, or Product which has been opened or tampered for any reason. Units which are found to

be damaged by abuse resulting in thermally damaged voice coils are not covered by this warranty but

may be replaced at the absolute and sole discretion of Directed. Unit must be returned to Directed,

postage pre-paid, with bill of sale or other dated proof of purchase bearing the following information:

consumer's name, telephone number, and address, authorized dealer's name and address, and product

description. Unit must be returned to the following address: ATTN: WARRANTY DEPARTMENT, Directed

Electronics , 1 Viper Way, Vista, CA 92081. Note: This warranty does not cover labor costs for the removal

and reinstallation of the unit. IN ORDER FOR THE TWO-YEAR WARRANTY TO BE VALID, YOUR UNIT

MUST BE SHIPPED WITH PROOF OF INSTALLATION BY AN AUTHORIZED DIRECTED DEALER. ALL UNITS

RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF DIRECTED DEALER INSTALLATION

AND PURCHASE WILL BE COVERED BY THE LIMITED 1 YEAR WARRANTY.

BY PURCHASING THIS PRODUCT, ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS

WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR

PURPOSE, AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY

EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR

AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF

THE PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES

INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. IN NO EVENT WILL DIRECTED BE LIABLE FOR ANY

INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFITS). BY PURCHASING

THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER

AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY,

CALIFORNIA. This warranty is only valid for sale of Product within the United States of America. Product

sold outside of the United States of America is sold “AS-IS,” and shall have NO WARRANTY, express or

implied. Some states do not allow limitation on how long an implied warranty lasts. In such states, the

limitation or exclusions of this Limited Warranty may not apply. Some states do not allow the exclusion

or limitation of incidental or consequential damages. In such states, the exclusion or limitation of this

Limited Warrantymay not apply to you. This Limited Warranty gives you specific legal rights, and you may

have other rights which vary from state to state.

920-0033 Rev 02-07

To find out more about other Precision Power products please visit: www.precisionpower.com

Peavey Computer Monitor 12PM User Manual
Philips Bottle Warmer SCF613 20 User Manual
Philips Cassette Player AZ122 User Manual
Philips Switch SWV2030 93 User Manual
Philips Telephone SE4502B 17 User Manual
Pitco Frialator Fryer SE14 User Manual
Pixel Magic Systems Flat Panel Television PE1000 User Manual
Planet Technology Network Router WAP 1966 User Manual
Poulan Tiller 174222 User Manual
PYLE Audio CRT Television PLVWR750T User Manual