Belkin Surge Protector AG110030 04 User Manual

Conserve Surge Protector  
Conserve Surge Protector  
1. INTRODUCTION  
2. OPERATION  
Thank you for purchasing the Conserve energy-saving surge protector from Belkin. Many devices today are never truly  
off but instead continue to consume electricity while in a standby mode. Standby mode or “phantom power” is wasted  
energy and it adds up quickly. Conserve makes it easy to reduce your electricity consumption by completely turning off  
the power to electronic devices when they are not in use.  
The Conserve energy-saving surge protector is already preset to work with the wireless remote switch. Only adjust the  
channel setting if:  
You have more than one Conserve surge protector and want to control each one independently.  
You want to control more than one Conserve surge protector using the same wireless remote switch.  
You think there is interference on the preset channel and you want to try other channels.  
Please be sure to read through this User Guide carefully to ensure proper installation and setup of the Conserve  
surge protector.  
Syncing your Conserve Surge Protector and Wireless Remote Switch  
To change the channel setting, use a small screwdriver to shift the keys on the surge protector and the wireless remote  
switch. Make sure the keys on the wireless remote switch and the surge protector have the same configuration (up to  
eight possible settings). Example:  
Not Matching/Not Synced  
Matching/Synced  
0
1
0
1
0
1
0
1
Circuit Breaker  
Reset Switch  
Remote  
Surge Protector  
Remote  
Surge Protector  
For ultimate convenience, control multiple Conserve surge protectors with a single remote switch. Adjust the channel  
setting on each Conserve unit to match the setting on the remote switch. This will allow you to easily turn off the power to  
additional devices connected to the units within range.*  
Channel Selector  
(Back of Surge Protector)  
Connecting your equipment  
Not Grounded Indicator Light  
The Conserve surge protector has ten (10) outlets. The outlets  
marked “Always On Outlets” are always powered when the  
surge protector is plugged in. They are not switchable. These  
outlets are intended for use with devices that typically need to  
stay on at all times.  
Always On  
• DVR/TiVo®  
• VoIP Phone  
Two (2) Always On Outlets  
Switched  
• TV  
• DVD player  
Protected/Always On  
Indicator Light  
Detachable Wireless Remote  
Switch with Wall-Mount  
Channel Selector  
(Back of Remote)  
• Stereo system  
• Computer monitor  
• Printer  
• MP3 player charger  
• Cell-phone charger  
• Any device that doesn’t  
need to be on 24/7  
The outlets labeled “Remote Switched Outlets” are controlled  
via the wireless remote switch. These outlets are intended for  
use with devices that do not need to be on all the time or go into  
standby mode when not in use. See illustration for examples.  
Manual Override Switch and  
Indicator Light  
The coaxial connectors (1 in, 1 out) provide added surge  
protection for audio video equipment. These connectors are  
not controlled by the wireless remote switch, since power is not  
supplied through the coax.  
Eight (8) Remote  
Switched Outlets  
The manual override switch on the surge protector can also be  
used to turn the switched outlets on or off without the wireless  
remote switch in the event the remote is lost or the battery  
needs replacing.  
Sliding Safety Covers  
Using the Wireless Remote Switch  
An A23 (12V) alkaline battery is included. Before using the wireless remote switch for the first time, simply remove the  
battery security tab from the switch. Now the switch is ready.  
A green LED on the wireless remote switch will illuminate when the switch is pressed. This indicates that the signal was  
sent and that the battery is OK. If you do not see the light, it is time to replace the battery. To replace the battery, see the  
Troubleshooting Guide on the next page.  
Coaxial Connectors (1 in, 1 out)  
Cable Management System  
(Clip not shown)  
Conserve has a range of up to 60 feet.* Line of sight from the wireless remote switch to the surge protector is  
not required.  
*Actual range may vary depending on interference, building materials (e.g., masonry, metal walls), and other location-specific conditions.  
CONseRve UseR GUIDe  
INTRODUCTION  
OPeRaTION  
 

Bissell Vacuum Cleaner 88D6 User Manual
Blodgett Fryer BLP 40G User Manual
Bosch Appliances Home Security System ICP CC404 User Manual
Boston Acoustics Car Stereo System GT 42 User Manual
Briggs Stratton Portable Generator 205051GS User Manual
Broil King Food Warmer NWT 1S User Manual
Brother Printer PT 530 User Manual
Canon Scanner LiDE 35 User Manual
Casio Credit Card Machine QT 2100 User Manual
Cisco Systems Computer Hardware 5580 User Manual