Installation and Assembly:
Universal Flat Wall Mount for 10" - 37" LCD Flat Panel
Screens
Models: SF 635P, SF 635P-S, SF 635, SF 635-S, SF 632P, SF 632P-S, SF 632,
SF 632-S
This product is UL Listed. It must be
installed by a qualified professional
installer.
Features:
• For 10" to 37" flat panel screens
R
• Ultra-slim design holds the screen flat against the wall
Max UL Load Capacity: 115 lb (52.2 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06
Parts List
SF 635P,
SF 632P
Qty Part #
SF 635P-S, SF 635,
SF 635-S,
SF 632-S
Part #
SF 632P-S
Part #
SF 632
Part #
Description
A wall plate
B hook bracket
C adapter plate
D M5 x 12 mm screw
E M5 x 6 mm phillips screw
F #10 SAE washer
G #14 x 2.5" hex head wood screw
H Alligator® anchor
1
1
1
2
4
4
2
2
4
4
4
4
4
4
1
095-1320
095-1321
095-1322
520-1027
520-1023
540-9400
095-4320
095-4321
095-4322
520-1027
520-1023
540-9400
095-1320
095-1321
095-1322
520-1064
520-1023
540-9400
095-4320
095-4321
095-4322
520-1064
520-1023
540-9400
5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03
590-0097
520-1128
520-9402
510-9109
504-9012
504-9020
590-5005
590-0097
520-1128
520-9402
510-9109
504-9012
504-9020
590-5005
590-0097
520-1128
520-9402
510-9109
504-9012
504-9020
590-5005
560-1145
590-0097
520-1128
520-9402
510-9109
504-9012
504-9020
590-5005
560-1145
I
J
M6 x 12 mm phillips screw
M6 x 20 mm phillips screw
K M6 x 30 mm phillips screw
L M4 x 10 mm phillips screw
M M4 x 20 mm phillips screw
N .198" ID x .313" OD x .437" H retaining spacer
O 4 mm security allen wrench
B
A
C
O
D
E
F
G
H
I
J
K
L M N
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06
3 of 8
Installation to Single Wood Stud Wall
WARNING
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based
on its edges, draw a vertical line down the stud’s center. Place wall plate (A) on wall as a template, making sure that
the two mounting holes are over the stud centerline. Level plate, and mark the center of the two holes. Drill two
5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using two #14 x 2.5"
wood screws (G) as shown.
1
Skip to step 2 on page 6 for VESA 200 mm and 200 mm x 200 mm patterns.
Skip to step 2 on page 7 for VESA 75 mm and 100 mm patterns.
WARNING
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers
are responsible to provide hardware for other types of mounting situations.
A
G
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06
4 of 8
Installation to Solid Concrete or Cinder Block
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
Make sure that wall plate (A) is level, use it as a
1
template to mark two mounting holes. Drill two 1/4"
(6 mm) dia. holes to a minimum depth of 2.5" (64
mm). Insert anchors (H) in holes flush with wall as
shown (right). Place wall plate over anchors and
secure with two #14 x 2.5" screws (G). Level, then
tighten all fasteners.
concrete
surface
1
H
Skip to step 2 on page 6 for VESA 200 mm and
200 mm x 200 mm patterns.
Drill holes and insert anchors (H).
2
Skip to step 2 on page 7 for VESA 75 mm and
100 mm patterns.
A
WARNING
H
G
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
Place plate (A) over anchors (H) and secure with screws (G).
3
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
• Always attach concrete expansion anchors directly to
load-bearing concrete.
Tighten all fasteners.
• Never attach concrete expansion anchors to concrete
covered with plaster, drywall, or other finishing mate-
rial. If mounting to concrete surfaces covered with a
finishing surface is unavoidable, the finishing surface
must be counterbored as shown below. Be sure
concrete anchors do not pull away from concrete
when tightening screws. If plaster/drywall is thicker
than 5/8", custom fasteners must be supplied by
installer.
H
A
CORRECT
INCORRECT
wall plate
concrete
concrete
wall
plate
G
plaster/
drywall
plaster/
drywall
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06
5 of 8
Attaching Adapter Plate to Screen with VESA 200 or 200 x 200 Mounting Pattern
Note: For VESA 75 mm and 100 mm patterns, see
followingpage.
C
Thread M5 socket pin screws (D) to hook bracket (B)
2
making the screws flush with bracket as shown.
Attach hook bracket (B) to adapter plate (C) using
four M5 x 6 mm screws (E) and #10 washers (F) as
B
shown.
F
E
D
WARNING
• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not
tightly secured, damage may occur to screen or product may fail.
FORVESA200MOUNTINGPATTERN:
FOR VESA 200 x 200 MOUNTING PATTERN:
3
Choose hole pattern as shown below. Attach adapter
plate (C) to back of screen using four M4 x 10 mm
screws (L) as shown below.
Choose hole pattern as shown below. Attach adapter
plate (C) to back of screen using four M6 x 12 mm
screws (I) as shown below.
*Note: If screw (L) gets less than three threads of
engagement, attach adapter plate (C) to back of
screen using four M4 x 20 mm screws (M) and four
spacers (N) as indicated below.
*Note: If screw (I) gets less than three threads of
engagement, attach adapter plate (C) to back of
screen using four M6 x 20 mm screws (J). If screw
(J) still gets less than three threads of engagement,
use four M6 x 30 mm screws (K).
Skip to step 4 on page 8.
Skip to step 4 on page 8.
C
*For screens with a hole
pattern in a pocket,
spacers (N) go between
adapter plate (C) and
screen.
C
L
I
N
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06
6 of 8
Attaching Hook Bracket to Screen with VESA 75 or 100 Mounting Pattern
Thread M5 phillips screws (D) to hook bracket (B)
making the screws flush with bracket as shown in
figures 2.1 and 2.2.
2
B
B
D
fig. 2.1
D
fig. 2.2
WARNING
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
FORVESA75MOUNTINGPATTERN:
FORVESA100MOUNTINGPATTERN:
3
Choose hole pattern as shown below. Attach hook
bracket (B) to back of screen using four M4 x 10 mm
screws (L) as shown below.
Choose hole pattern as shown below. Attach hook
bracket (B) to back of screen using four M4 x 10 mm
screws (L) as shown below.
*Note: If hole pattern is in a pocket, attach hook
bracket (B) to back of screen using four M4 x 20 mm
screws (M) and four spacers (N) as indicated below.
B
B
L
L
*For screens with a hole
pattern in a pocket,
spacers (N) go between
hook bracket (B) and
N
screen.
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06
7 of 8
Installing and Removing Flat Panel Screen
Hook screen onto wall plate (A) figure 4.1. Tighten
M5 x 12 mm screws (D), shown in figure 4.2 and
detail 1.
SCREEN
4
A
Note: For security models, use 4 mm security allen
wrench (O) to tighten M5 x 12 mm screws (D).
To remove screen from mount, loosen screws (D)
and lift screen off of mount.
WARNING
• Do not lift more weight than you can handle. Use
additional man power or mechanical lifting equipment
to safely handle placement of the screen.
• Failure to lock hook bracket with screws (D) can
cause screen to come off mount if hit accidentally.
CAUTION
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 20 in. • lb (2.26 N.M.) maximum torque.
fig. 4.1
B
A
A
B
D
D
fig. 4.2
DETAIL 1
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06
8 of 8
©2005PeerlessIndustries,Inc.Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
|