Philips Clock Radio ORT7500 User Manual

Always there to help you  
Register your product and get support at  
ORT7500  
Question?  
Contact  
Philips  
User manual  
 
Contents  
1 Safety  
2
2
11 Product information  
General information  
Tuner  
16  
16  
16  
16  
16  
16  
Important notes for users in the U.K.  
Amplifier  
Speakers  
Bluetooth  
2 Your DAB+ Radio  
Introduction  
4
4
4
5
What's in the box  
Overview of the product  
12 Troubleshooting  
General  
17  
17  
17  
3 Get started  
Connect power  
Turn on  
6
6
6
6
About Bluetooth connection  
Set the clock  
13 Notice  
18  
18  
18  
18  
18  
Compliance  
Care of the environment  
Trademark notice  
Copyright  
4 Listen to FM radio stations  
Search for a radio station automatically  
Store radio stations automatically  
Program radio stations manually  
Display RDS information  
7
7
7
8
8
9
Adjust FM settings  
5 Listen to DAB radio stations  
For the first time use  
10  
10  
10  
10  
11  
Program radio stations  
Display DAB information  
Use DAB menus  
6 Use system menus  
Check the current software version  
Reset the product  
12  
12  
12  
12  
Upgrade the software  
7 Listen to an external device  
8 Play audio via Bluetooth  
9 Charge your devices  
10 Adjust the volume  
13  
14  
15  
15  
EN  
1
 
This product shall not be exposed to  
dripping or splashing!  
Do not place any sources of danger on this  
product (e.g. liquid filled objects, lighted  
candles).  
Never place the product or any objects  
on power cords or on other electrical  
equipment.  
If the product is transported in  
temperatures below 5°C, unpack the  
product and wait until its temperature  
matches room temperature before  
connecting it to the power outlet.  
Only use attachments/accessories specified  
by the manufacturer.  
1 Safety  
Read and understand all instructions before you  
use this product. If damage is caused by failure  
to follow the instructions, the warranty does  
not apply.  
Risk of electric shock or fire!  
Never expose the product and accessories  
to rain or water. Never place liquid  
containers, such as vases, near the product.  
If liquids are spilt on or into the product,  
disconnect it from the power outlet  
immediately. Contact Philips Consumer  
Care to have the product checked before  
use.  
Risk of overheating!  
Never install this product in a confined  
space.Always leave a space of at least four  
inches around the product for ventilation.  
Make sure that curtains or other objects  
never cover the ventilation slots on the  
product.  
Never place the product and accessories  
near naked flames or other heat sources,  
including direct sunlight.  
Never insert objects into the ventilation  
slots or other openings on the product.  
Where the mains plug or an appliance  
coupler is used as the disconnect device,  
the disconnect device shall remain readily  
operable.  
Note  
The type plate is located on the back of the product.  
Disconnect the product from the power  
outlet before lightning storms.  
When you disconnect the power cord,  
always pull the plug, never the cable.  
Never remove the casing of this product.  
Important notes for users in  
the U.K.  
Risk of short circuit or fire!  
Mains fuse  
Before you connect the product to the  
power outlet, make sure that the power  
voltage matches the value printed on the  
back of the product. Never connect the  
product to the power outlet if the voltage  
is different.  
This information applies only to products with a  
UK mains plug.  
This product is fitted with an approved molded  
plug. If you replace the fuse, use one with:  
the ratings shown on the plug,  
a BS 1362 approval, and  
the ASTA approval mark.  
Never expose the product to rain, water,  
sunshine, or excessive heat.  
Avoid force coming onto power plugs.  
Loose power plugs can cause arcing or fire.  
Contact your dealer if you are not sure about  
what type of fuse to use.  
Risk of injury or damage to the product!  
2
EN  
 
Caution:To conform with the EMC directive  
(2004/108/EC), do not detach the plug from  
the power cord.  
How to connect a plug  
The wires in the power cord are colored as  
follows: blue = neutral (N), brown = live (L).  
If the colors do not correspond with the colors  
on your plug, identify the terminals in your plug  
as follows:  
1
2
3
Connect the blue wire to the terminal  
marked N or colored black.  
Connect the brown wire to the terminal  
marked L or colored red.  
Do not connect either wire to the earth  
terminal in the plug, marked E (or e) or  
colored green (or green and yellow).  
Before you replace the plug cover, make sure  
that the cord grip is clamped over the sheath  
of the cable and not just over the two wires in  
the cable.  
Copyright in the U.K.  
Recording and playback of material may require  
consent. see Copyright Act 1956 andThe  
performer's Protection Acts 1958 to 1972.  
EN  
3
 
2 Your DAB+  
Radio  
What's in the box  
Check and identify the contents of the package:  
a Digital radio  
b User manual  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from the  
support that Philips offers, register your product  
c Audio in cable  
d AC power cord  
e UK power cord  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from the  
support that Philips offers, register your product  
Introduction  
With this product, you can:  
listen to FM radio stations (RDS  
supported),  
OR7200  
listen to DAB radio stations,  
listen to audio from an external device  
through the AUDIO-IN socket,  
listen to audio from an external device via  
Bluetooth connection.  
User Manual  
4
EN  
 
Press to switch the system between  
standby mode and normal mode.  
Overview of the product  
Turn to adjust the volume.  
i
h
a
b
g
f
e
c
d
n
j
k
m
l
e
a INFO  
In FM mode, turn to tune to a radio  
station manually.  
Press repeatedly to display available  
information.  
Turn to toggle through FM or DAB  
menus.  
b SCAN  
Press to activate the search for the  
Under FM or DAB menus, press to  
enter lower level menus or confirm an  
option.  
next strong FM radio station.  
Press and hold to activate the  
automatic search for and storage of  
FM radio stations.  
f PRESET  
Turn to select a preset radio station.  
g PROGRAM  
Press to activate the programming of  
radio stations.  
Turn to switch the system from  
standby mode to normal mode.  
h MENU  
d
EN  
5
 
Press to enter or exit FM or DAB  
menus.  
3 Get started  
i LCD screen  
j AC MAIN~  
Always follow the instructions in this chapter in  
sequence.  
Connect to the AC power cord.  
k AUDIO IN  
Connect to an external device by an  
audio in cable.  
Connect power  
l DAB SOFTWARE  
The socket for firmware upgrade  
m
USB socket,charge the device only  
n Antenna  
Connect the AC power cord to the AC  
MAIN~ socket and then to the wall outlet.  
Turn on  
Press the knob or turn the SOURCE knob.  
» The product switches to the last  
selected source.  
To switch the product to standby  
mode, press the knob again.  
Set the clock  
1
In standby mode, press and hold the  
knob for 2 seconds.  
»
(12-hour time format) or  
(24-hour time format) blinks.  
2
3
Turn the  
and then press the  
» Hour digits blink.  
knob to select a time format,  
knob to confirm.  
Turn the  
press the  
knob to set the hour, and then  
knob to confirm.  
6
EN  
 
» Minute digits blink.  
4 Listen to FM  
radio stations  
4
5
6
Turn the  
Press the  
Turn the  
knob to set the minute.  
knob to confirm.  
knob to select whether to  
synchronize the DAB clock and then press  
the knob to confirm  
1
2
Turn the SOURCE knob to switch the  
product to FM mode.  
Search for radio stations automatically or  
manually.  
Search for a radio station  
automatically  
Press SCAN to activate the auto search.  
Note  
For optimal reception, fully extend the antenna and  
adjust its position.  
You can store a maximum of 30 FM radio stations.  
» After a strong radio station is detected,  
the search stops and the radio station  
is broadcast.  
Search for a radio station  
automatically  
Press SCAN to activate the auto search.  
» After a strong radio station is detected,  
the search stops and the radio station  
is broadcast.  
Store radio stations  
automatically  
Press and hold SCAN to activate the auto  
search.  
» After the search is complete, the first  
stored radio station is broadcast.  
To tune to a stored radio station, turn  
the PRESET knob until its frequency is  
displayed.  
EN  
7
 
Display RDS information  
Radio Data System (RDS) is a service that  
allows FM stations to transmit additional  
information.When you tune to an FM radio  
station that transmits RDS signals, the station  
name is displayed.  
2 sec.  
1
2
Tune to an RDS station.  
Press INFO repeatedly to scroll through  
the following information (if available):  
Radio text  
Program type such as [NEWS] (news),  
[SPORT] (sport), [POP M] (pop  
music)...  
Program service  
Mono/Stereo  
Time  
Date  
RDS program types  
Program radio stations  
manually  
Pro-  
gram  
type  
Description  
Program Descrip-  
type tion  
1
2
Tune to a radio station.  
NEWS News services  
FINANCE Finance  
Politics and currentCHIL- Children's  
programs  
Press the PROGRAM button to activate  
the programming.  
AF-  
FAIRS affairs  
DREN  
3
4
Turn the  
sequence number.  
knob to select a preset  
INFO Special informationSOCIAL Social af-  
programs  
SPORT Sports  
EDU- Education and  
fairs  
RELIGIONReligion  
PHONE Phone in  
Press the  
knob to confirm.  
» The radio station is stored with the  
selected sequence number.  
CATE advanced training IN  
DRA- Radio plays and TRAVEL Travel  
5
Repeat steps 1-4 to program more radio  
stations.  
To tune to a preset radio station, turn  
the PRESET knob until its frequency is  
displayed.  
MA  
literature  
CUL- Culture, religion LEISURE leisure  
TURE and society  
SCI-  
Science  
JAZZ  
Jazz Music  
ENCE  
VAR- Entertainment  
IED programs  
POP M Pop music  
COUN- Country  
TRY Music  
NATION National  
Music  
Note  
If you store a radio station with the sequence number  
of another one, the earlier one is overwritten.  
M
ROCK Rock music  
M
OLDIES Oldies  
Music  
8
EN  
 
: Convert stereo signals  
to monophonic output even if the  
station transmits strong stereo audio  
signals.  
MOR Light music  
M
LIGHT Light classical  
FOLK M Folk Music  
DOCU- Documen-  
M
music  
MENT  
tary  
3
Press the  
knob to confirm the option.  
CLAS- Classical music  
SICS  
TEST  
AlarmTest  
OTH- Special music  
ER M programs  
ALARM Alarm  
System menus  
WEATHER  
Weather  
1
Press the  
Turn the  
For details, refer to the section 'Use  
knob to access system menus.  
knob to select a sub-menu.  
Adjust FM settings  
2
1
In FM mode, press MENU to access FM  
menus.  
system menus'.  
2
Turn the  
menus.  
knob to toggle through the  
Scan setting  
1
2
Press the  
knob to access sub-menus.  
Turn the  
knob to select an option.  
: Search for strong  
stations only.  
: Search for all stations  
no matter whether the signal strength  
of a station is strong or weak.  
3
Press the  
knob to confirm the option.  
Audio setting  
1
2
Press the  
knob to access sub-menus.  
Turn the  
knob to select an option.  
:Allow stereo  
output even if the station transmits  
weak stereo audio signals.  
EN  
9
 
H:The station is one of your 10 favorite  
stations.  
?:The station is unavailable or inactive.  
:The station is a primary station with  
secondary service.  
5 Listen to DAB  
radio stations  
:The station is a secondary station.  
Note  
Program radio stations  
For optimal reception, fully extend the antenna and  
adjust its position.  
You can program a maximum of 30 DAB radio stations.  
for applicable DAB radio frequencies in your area.  
1
2
Tune to a DAB radio station.  
Press PROGRAM to activate the  
programming.  
3
4
Turn the  
sequence number.  
knob to select a preset  
Press the  
knob to confirm.  
For the first time use  
» The radio station is stored with the  
selected sequence number.  
1
2
3
Turn the SOURCE knob to switch the  
product to DAB mode.  
5
Repeat steps 1-4 to program more radio  
stations.  
To tune to a preset radio station, turn  
the PRESET knob until its frequency is  
displayed.  
Turn the  
knob until the [Full scan]  
menu is displayed.  
Press the  
knob to activate the  
automatic search.  
» This product automatically stores radio  
stations with sufficient signal strength.  
Note  
» After the search is complete, the  
first stored radio station is broadcast  
automatically.  
If you store a radio station with the sequence number  
of another one, the earlier one is overwritten.  
4
Turn the  
then press the  
knob to select a station, and  
knob to start listening.  
Display DAB information  
Tip  
On the display of DAB broadcasting, the first  
line shows station name, and the second line  
shows the service information for the current  
station.  
You can re-scan to update the list of stored stations  
(see "Use DAB menus" > "Re-scan for stations").  
You can tune to a station manually (see "Use DAB  
menus" > "Tune to a station manually").  
Press INFO repeatedly to cycle through the  
following information (if available).  
Dynamic label segment (DLS)  
Signal strength  
Program type (PTY)  
Ensemble name  
About special symbols  
Some symbol may be displayed before the  
name of a station.  
Frequency  
10 EN  
 
Signal error rate  
Bitrate codec  
Time  
Tune to a station manually  
With this feature, you can tune to a specific  
channel/frequency manually. In addition to  
antenna orientation for better radio reception,  
the optimal reception can also be obtained with  
this feature.  
Date  
Use DAB menus  
1
In DAB mode, press MENU to access the  
DAB menus.  
2
Turn the  
menus.  
knob to toggle through the  
1
2
Press the  
knob to access the station list.  
knob to select a station from  
Turn the  
5A to 13F.  
Tune to a stored station  
3
Press the  
knob to confirm the option.  
1
Press the  
stored stations.  
If no DAB station is stored, the product  
starts automatic search.  
knob to access the list of  
DRC (Dynamic Range Control)  
DRC adds or removes a degree of  
compensation for the differences in the dynamic  
range between radio stations.  
2
3
Turn the  
Press the  
knob to select a station.  
knob to start listening.  
Re-scan for stations  
Full scan is used to perform a wide range  
search for DAB radio stations.  
1
2
Press the  
menus.  
knob to access the sub-  
Turn the  
knob to select an option. (The  
asterisk behind the option indicates the  
current setting.)  
: No compensation applied.  
Press the  
knob to start scanning for available  
DAB stations.  
: Medium compensation  
applied.  
applied.  
» After the scanning is complete, the first  
detected station is broadcast.  
: Maximum compensation  
3
Press the  
knob to confirm the option.  
EN 11  
 
Remove invalid stations  
6 Use system  
menus  
This option lists active stations and removes any  
stations that are in the list but have no service  
in your area. In front of the station name of an  
invalid station, a question mark (?) is displayed.  
Use the system menus to  
check the version of current software of  
this product,  
upgrade the software, and  
reset the product to factory default status.  
1
2
Press the  
menus.  
knob to access the sub-  
Turn the  
knob to select an option.  
: Return to the previous menu.  
Check the current software  
version  
: Remove invalid stations from  
the station list.  
3
Press the  
knob to confirm the option.  
System menus  
Press the  
knob to display the version of  
current software.  
Reset the product  
1
Press the  
Turn the  
For details, refer to the section 'Use  
knob to access system menus.  
knob to select a sub-menu.  
2
system menus'.  
1
2
Press the  
knob to display the options.  
Turn the  
knob to select an option.  
: Return to the previous menu.  
: Reset the product to factory  
default status.  
3
Press the  
knob to confirm the option.  
Upgrade the software  
12 EN  
 
7 Listen to an  
external device  
1
2
Search for support information about  
your product with "ORT7500/12" as the  
keyword.  
» When an upgrade packet is available,  
the link of "Firmware Upgrade  
Readme File" is accessible.The exact  
wording of this link name may vary in  
different languages.  
You can also listen to an external audio device,  
for example, MP3 player, through this product.  
1
2
Turn the SOURCE knob to switch the  
product to AUDIO IN mode.  
Connect the audio in cable to  
the AUDIO IN socket on the back  
panel of this product, and  
the headphone jack on the external  
device.  
3
4
5
Click the link of "Firmware Upgrade  
Readme File".  
3
Play the external device (refer to its user  
manual).  
Read and understand the instructions on  
software upgrade.  
Follow the instructions to complete the  
upgrade.  
EN 13  
 
2
3
On your device, search for Bluetooth  
devices. In the device list, select ORT7500.  
8 Play audio via  
Bluetooth  
If a message prompts for the  
permission for Bluetooth connection  
with ORT7500, confirm it.  
» If the connection succeeds, [BT  
Connected] is displayed on the LCD  
display of this product.  
With this product, you can stream audio from a  
Bluetooth player.  
Play a track on the connected device.  
An application Philips DigitalRadio is available  
on Apple App Store and Google Play.To fully  
enjoy features of this product, download and  
install the application to your smart device.  
To pause or resume play, press  
To skip to the previous or next track,  
press  
.
/
.
Note  
Philips does not guarantee the compatibility with all  
Bluetooth devices.  
Before pairing a device with this system, read its user  
manual for Bluetooth compatibility.  
The product can memorize a maximum of 4 paired  
devices.  
Make sure that Bluetooth function is enabled on your  
device, and your device is set as visible to all other  
Bluetooth devices.  
The operational range between this system and a  
Bluetooth device is approximately 10 meters (30 feet).  
Any obstacle between this system and a Bluetooth  
device can reduce the operational range.  
Keep away from any other electronic device that may  
cause interference.  
Note  
/
If the connected Bluetooth device supports the  
Advanced Audio Distribution Profile (A2DP), you can  
listen to tracks that are stored on the device through  
the system.  
If the device also supports the AudioVideo Remote  
Control Profile (AVRCP), you can control play on this  
product.  
If the connected device does not support the AVRCP,  
control play on the connected device.  
1
Turn the SOURCE knob to switch the  
product to BT mode.  
» If no Bluetooth device is connected,  
[Bluetooth No Connection] (No  
Bluetooth connection) scrolls.  
14 EN  
 
9 Charge your  
devices  
10 Adjust the  
volume  
Connect your device to the USB  
socket on  
Turn the knob.  
the back of the product.  
» Once the device is recognized, the  
charging starts.  
Note  
Philips does not guarantee the compatibility of this  
product with all devices.  
The USB  
socket is for charging only.  
EN 15  
 
Frequency Response  
60 Hz - 16 kHz,  
±3 dB  
> 65 dB  
11 Product  
information  
Signal to Noise Ratio  
Aux Input  
0.5V RMS 20 kohm  
Note  
Product information is subject to change without prior  
notice.  
Speakers  
Speaker Impedance  
Speaker Driver  
Sensitivity  
6 ohm  
2 X 3" full range  
>82 dB/m/W  
General information  
AC Power Rating  
100-240V~,  
50/60 Hz  
Bluetooth  
Operation Power  
Consumption  
Standby power consumption  
Dimensions (Main Unit)  
15 W  
Communication Bluetooth Standard version  
system  
Output  
2.0  
< 1 W  
325 x 175 x  
167 mm  
Bluetooth Standard Power  
Class 2  
Line of sight approx. 10m  
Maximum  
communication (30 feet)  
range  
Weight (Main Unit)  
3.5 kg  
Frequency band 2.4 GHz band (2.4000 GHz  
- 2.4835 GHz)  
Tuner  
Tuning Range  
Compatible  
Bluetooth  
profiles  
Advanced Audio Distribution  
Profile (A2DP)  
FM: 87.50 - 108.00  
MHz;  
AudioVideo Remote  
Control Profile (AVRCP)  
SBC (Sub Band Codec)  
DAB: 174.928-  
239.200 MHz  
50 kHz  
Supported  
codecs  
Tuning grid  
SBC (Sub Band Codec)  
- Receive  
-Transmit  
DAB sensitivity  
(EN50248)  
Total Harmonic  
Distortion  
< -95 dbm  
< 2%  
Signal to Noise Ratio  
> 50 dB  
Number of preset radio  
stations  
30 (FM), 30 (DAB)  
Amplifier  
Rated Output Power  
10 W x 2 RMS  
16 EN  
 
Power has been interrupted, or the AC  
power adaptor has been disconnected.  
Set the clock again.  
12 Troubleshooting  
Warning  
Never remove the casing of this product.  
About Bluetooth connection  
Music playback is unavailable on this product  
even after successful Bluetooth connection.  
To keep the warranty valid, never try to repair  
the product yourself.  
The device cannot be used with this  
product to play music.  
If you encounter problems when using this  
product, check the following points before  
requesting service. If the problem remains  
unsolved, go to the Philips Web page (www.  
philips.com/support).When you contact Philips,  
make sure that the product is nearby and the  
model number and serial number are available.  
The audio quality is poor after connection  
with a Bluetooth-enabled device.  
The Bluetooth reception is poor. Move the  
device closer to this product or remove  
any obstacle between.  
Cannot connect with this product.  
General  
The device does not support the profiles  
required for this product.  
No power  
The Bluetooth function of the device is  
not enabled. Refer to the user manual of  
the device to find out how to enable the  
function.  
Make sure that the AC power cord is  
properly connected.  
Make sure that there is power at the AC  
power outlet.  
This product is not in the pairing mode.  
This product is already connected with  
another Bluetooth-enabled device.  
No sound  
Adjust the volume.  
Disconnect that device and then try again.  
When listening to an external device, make  
sure that the external device is not muted.  
The paired mobile device connects and  
disconnects constantly.  
No response from the product  
The Bluetooth reception is poor. Move the  
device closer to this product or remove  
any obstacle between.  
Make sure that the power is available.  
Turn off the product, and then turn it on  
again.  
Some mobile phones may connect and  
disconnect constantly when you make  
or end calls.This does not indicate any  
malfunction of this product.  
Poor radio reception  
Due to the interference from other  
electrics or building obstacles, the signals  
become weak. Move the product to a  
place free of interference.  
For some devices, the Bluetooth  
connection may be deactivated  
automatically as a power-saving feature.  
This does not indicate any malfunction of  
this product.  
Make sure that the antenna is fully  
extended.Adjust the position of the  
antenna.  
Clock setting is erased.  
EN 17  
 
When this crossed-out wheeled bin symbol is  
attached to a product it means that the product  
is covered by the European Directive 2002/96/  
EC. Please inform yourself about the local  
separate collection system for electrical and  
electronic products.  
13 Notice  
Any changes or modifications made to this  
device that are not expressly approved by  
WOOX Innovations may void the user’s  
authority to operate the equipment.  
Please act according to your local rules and  
do not dispose of your old products with your  
normal household waste.  
Correct disposal of your old product helps to  
prevent potential negative consequences for the  
environment and human health.  
Compliance  
Environmental information  
All unnecessary packaging has been omitted.  
We have tried to make the packaging easy to  
separate into three materials: cardboard (box),  
polystyrene foam (buffer) and polyethylene  
(bags, protective foam sheet.)  
This product complies with the radio  
interference requirements of the European  
Community.  
Your system consists of materials which can  
be recycled and reused if disassembled by  
a specialized company. Please observe the  
local regulations regarding the disposal of  
packaging materials, exhausted batteries and old  
equipment.  
A copy of the EC declaration of Conformity  
is available in the Portable Document Format  
(PDF) version of the user manual at www.  
philips.com/support.  
Trademark notice  
This is CLASS II apparatus with double  
insulation, and no protective earth provided.  
The Bluetooth® word mark and logos are  
registered trademarks owned by Bluetooth  
SIG, Inc. and any use of such marks by WOOX  
Innovations is under license.  
Care of the environment  
Copyright  
2013 © WOOX Innovations Limited.All rights  
reserved.  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused.  
Specifications are subject to change without  
notice.WOOX reserves the right to change  
products at any time without being obliged to  
adjust earlier supplies accordingly.  
18 EN  
 
EN 19  
 
20 EN  
 
EN 21  
 
Specifications are subject to change without notice  
All registered and unregistered trademarks are property of their respective owners.  
2013 ©WOOX Innovations Limited.All rights reserved.  
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by  
WOOX Innovations Limited under license from Koninklijke Philips N.V.  
ORT7500_10_UM_V2.0  
 

Peerless Industries TV Mount DS VW660 User Manual
Pelco Security Camera C2924M A 5 05 3 User Manual
Pelco Security Camera C2924M A 5 05 User Manual
Pentair Landscape Lighting Amerlite User Manual
Philips Baby Accessories SCF660 17 User Manual
Philips Iron GC4640i User Manual
Philips Projector PXG20 User Manual
Philips Water Dispenser WP3810 User Manual
Polaroid Tablet PMID705X User Manual
Poulan Trimmer 545014347 User Manual