Philips Work Light LSB 13 User Manual

Lighting Systems LSB-13  
1BHFꢃꢂꢃPGꢃꢆꢃ  
-ZUFTQSFBEÜꢃ-4#ꢃ3BEJBMꢃ-PVWFSꢃꢂꢌ-JHIUꢃ5ꢈꢃ1FSꢃꢍꢌ'PPUꢃ /PNJOBMꢊꢃ4FDUJPO  
8-1/2" (21.60 cm)  
1-3/4" (4.45 cm)  
2" (5.08 cm)  
3
1
4
2
3-1/2" (8.89 cm)  
Half Scale  
Ordering Information  
Family  
Lamps  
Length  
Shielding  
Ballast  
Voltage  
Finish  
LSB  
1
D
1 = 1-Lamp T5  
4 = 4-Foot  
D = Radial Louver  
28 = 28W T5  
1 = 120 volt  
AL = Aluminum  
8 = 8-Foot  
54 = 54W T5  
2 = 277 volt  
WH = White  
5E = 54W T5 Emergency Pack  
2E = 28W T5 Emergency Pack  
5D = 54W T5 Dimming  
Complete ordering instructions below.  
Features  
Ordering Instructions  
1. Housing: Extruded aluminum. Die-cast end cap mechanically attached with  
no exposed fasteners or hardware.  
Individual Fixtures:  
1. Order number of MODULES required.  
2. Lamping: One T5, 28 or 54 watt (as specified) fluorescent lamp per 4-foot  
nominal section. Provided by others.  
3. Reflector: Precision die-formed semi-specular aluminum.  
4. Radial Louver: Precision die-formed aluminum straight blade louver, blades  
are 5/8” (1.59cm) high and 5/8” (1.59cm) O.C.  
2. Order one POWER FEED END SET per MODULE.  
Continuous Rows:  
1. Determine run length.  
2. Order the appropriate number of MODULES for the complete  
run.  
3. Order one POWER FEED END SET per run.  
4. Order one CABLE ASSEMBLY per MODULE minus one  
per run.  
5. For runs that exceed amperage limits, order the appropriate  
number of CABLE/CORD ASSEMBLIES.  
Electrical  
Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color-  
coded quick connectors allow ease of connection for joiner modules. Power feed  
is 18 gauge white SJT. For special circuiting consult factory. Factory installed  
ballast disconnect allows the ballast to be disconnected from and reconnected to  
incoming power under load without turning the entire circuit off.  
Dimming: - 120/277 VAC 1% dimming level, 4 wire feed required.  
Emergency Battery Pack: - 28 watt: 520 lumens @ 90 minutes, 54 watt: 700  
lumens @ 90 minutes, 4 wire feed required.  
Labels  
UL, cUL, and I.B.E.W.  
Mountings  
Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white  
enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36”  
(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner  
modules.  
Job Information  
Type:  
Job Name:  
Cat. No.:  
Finish  
Powder coated baked white or aluminum finish. Custom colors available, consult  
factory.  
Options and Accessories  
Lamp(s):  
Notes:  
Emergency circuiting; special circuiting; X, T & L joiner blocks - consult factory.  
ꢀꢁꢂꢃ"JSQPSUꢃ3PBEꢄꢃ'BMMꢃ3JWFSꢄꢃ."ꢃꢅꢆꢇꢆꢅꢃtꢃ ꢈꢅꢉꢊꢃꢀꢇꢋꢌꢉꢂꢁꢂꢃtꢃ'BYꢃ ꢈꢅꢉꢊꢃꢀꢇꢍꢌꢍꢇꢂꢅ  
We reserve the right to change details of design, materials and finish.  
XXXꢎMJHIUPMJFSꢎDPNꢃ½ꢃꢆꢅꢅꢉꢃ1IJMJQTꢃ(SPVQꢃt #ꢅꢋꢅꢉ  
 

Philips Automobile Battery Charger SCM4327 User Manual
Philips Baby Accessories SCD149 60 User Manual
Philips Digital Photo Frame 6FF3FPW 37 User Manual
Philips MP3 Docking Station DC910W 37 User Manual
Philips MP3 Player SA6125 97 User Manual
Philips Portable DVD Player PET825 00 User Manual
Philips Remote Starter Remote Starter User Manual
Philips Vacuum Cleaner FC6091 User Manual
Polk Audio Portable Speaker DXI104 DVC User Manual
Porter Cable Sander 352VS User Manual